I popped a T9300 into my 5920G which went smoothly. But it seems its getting to hot...? I measured up to 66 Degrees C on the cores under load and 47 C idle.....? I though the stock processor T7500 and the T9300 disapated the same power?
View 10 RepliesI just upgraded to a T9300 CPU, I bought it in ebay for £120 only, brand new (not an ES), and it is great. It is much cooler than the T7300 I had. Idle temp is around 32oC where before were around 40-42 oC. Of course I don't know if that was because I put fresh AS paste on the CPU where before the T7300, I think, had a thermal pad (melted on the core).
To be honest though, changing the CPU wasn’t as easy as I was imagined. Unfortunately I didn’t take any photos as I didn’t know what I was doing but in the end all went well. I had to remove the graphic card and in order to remove the heat sink I had to remove a couple of other screws of the back chassis so I lifted it a bit to slide out carefully the heat sink. Then you remove the old CPU, clean the heat sink with ethanol and then place the new CPU, put some AS paste on the core and slide the heat sink in carefully and screw it tight on its place.
It is slightly faster in the games and much faster in using other software like movie maker. The games are running much smoother now but that is with games that are close to 21-24fps. World in Conflict uses a lot of that CPU. I ran the benchmark and with High physics and the CPU usage was 98-100%, both cores. During gaming is much less around 35%, explosions produce CPU usage spikes. Temp of CPU is around 65oC most of time during gaming, but it can go up to 68oC if you demand more from the CPU. My wPrime 32M score was 41s-42s with the T7300 and now is just below 30s (29.687s). My 3Dmark06 score increased as well from 4240 to 4567. I am very pleased with the end result.
Next thing is to upgrade to fast RAM like the 4GB (2x2GB) HyperX Kingston CL4 667MHz or 800MHz, then 320GB WD hard drive Black Scorpio and maybe try to upgrade to a new graphic card compatible with Acer 5920G with at least 512MB memory (9600M GS perhaps).
I believe that my Acer Aspire 5920G was getting too hot, so I checked the temps:
CPU: 81C
GPU: 73C
HDD: 55C
I'm afraid those temperatures are too high. I don't understand why this happens! I don't play games that much now, I have cleaned the laptop's fans recently and I have the air-conditioner on all the day to keep the room with the laptop cool.
What can I do to decrease temps? I don't want to spend money, because I'm having problems with that laptop and my 8600M GS might die soon...
I have a 5920G with the 160GB HDD and the 8600 GT graphics card.
I upgraded the RAM to 3GB which didn't such a big change to be honest, but it did help with my Ubuntu partition.
Anyway I have a few niggles and some bigger issues with it:
1) whenever I play games such as Day of Defeat/Counter Strike Source, the computer shuts down after about 20 minutes. It just overheats, badly. It feels really, really hot at times when I play. I don't play with heavy graphics, more like the opposite in fact.
It ran Modern Warfare 1 but again, for less than 10 minutes before shutting off.
I have it on a wooden desk, so there's not much air circulating under the laptop. I tried propping it higher up with various things but to no avail.
I don't quite understand what I can do... what's the point in getting a decent graphics card in a high powered PC (my PC before was a P Celeron with 256MB RAM ) if it's not going to be able to run it fast due to overheating..? I'm a little at lost.
2) and that's mostly a niggle... I used Media Monkey as my media player, and PlayMovie as my DVD player.
Whenever I have a DVD in the player, and I use MediaMonkey, the play/pause media key brings up the Windows Media Player to start playing the DVD. It's very frustrating as I have something in the DVD player most of the time and I basically play music out of it whenever it's even on. I'd uninstall WMP but that's basically impossible...
So I'd love to be able to use that media key without anything popping up to full screen and making everything else lag, if it's possible...
The irony there is that while Ubuntu didn't see those media keys at first, a little script later with the help of the Ubuntu forum and they now work BETTER with any media player.
Don't know what else... I tried the latest graphics card driver and wouldn't advise it, I rolled back. Otherwise it's a nice laptop for sure.
is it a good idea to get a T9300 and overclock it to 2.6 GHz-2.8 GHz? The only difference (according to Intel's sheets) is the clock speed between T9300 and T9500.
I plan to buy a T9500/T9300 and put it in my Acer Aspire 6920G. Hopefully T9300 and OC.
My 6920G currently has a T9300 which is 2.5ghz on the 800MT/s FSB
Is the best CPU I can fit the T9500?
By my understanding, everything quicker than the T9500 has the 1066MT/s FSB and won't work? Is this correct?
Would you consider the performance increase from T9300 to T9500 worth the money and hassle?
Have a t9300 from an HP Pavillion that died, and figured I could best put it to use in my new Acer 7738g, which currently has a t6500. I've heard it's possible but the whole socket M/socket P thing has me scratching my head...
Also not sure if the 7738 is one of those take-everything-apart-to-get-to-the-CPU jobs or just uncrew the base... and then eventually the heat sink to get to the CPU...anyone with experience with this series?
The cpu Intel Core 2 Duo T9300 SLAYY is compatibile with the intel gl40 chipset. But is compatible also with the Acer Extensa 5230? (bios 1.28)
Instead the T5750 is compatible with this notebook?
i have laptop Acer 5920G
VGA card NVIDIA GeForce 8600 GT
but its performance very bad and i cant believe its up 2 1024
i barely can play FIFA 2007 and its slow!
is it up 2 VGA driver?
setup icon details say it's version is 9.1.0.429
is their any new drivers 4 it .........
I recently purchased a XPS M1530 and it arrived with the T5750 2.0 GHZ Processor. I decided to upgrade it soon to the T9300. I was wondering if doing so there would be a noticeable performance increase in various processes (Gaming,etc).
View 10 Replies View RelatedMy 5920G which I got for Christmas is giving me some problems.
I have gone to power options and and changed the settings so when I close the lid, nothing must happen. But when I come back in about 20 minutes after leaving the lid closed, there is no way of me getting the LCD to start up. The only way I can get past this is by pressing the power button in for a few seconds forcing it to shut down. Obviously this is bad for my notebook. How do I get this sorted out? The same thing happens if I leave the lid open and come back in a while.
I bought the XPS M1330 when it first came out in the UK
I have the T7100 1.8ghx CPU and 2GB Ram and Running Vista Business
I find that authoring DVDs and playing games can be a bit slow, so I wanted to Upgrade the power of my CPU.
Can anyone suggest a good CPU to upgrade to, which is compatable with the 1st M1330 ? - I hear that the T9300 is a good one but I dont know anythiing about compatability?
Also, wouyld you recommend another 3GB of RAM? - (Even though I hear that Vista 32 bit only supports 3GB RAM?)
Which processor is better @ stock clocks? The older 2.8 or the newer 2.5?
View 8 Replies View RelatedJust upgraded the CPU in my M1530 this afternoon from a 1.66gHz T5450 to a 2.5gHz T9300.
View 4 Replies View RelatedI've got a PM45 based notebook (DV7t-2080) which currently has a T6400 (Penryn 2M, 2.0ghz, 35Watt tdp)
The question is - will the PM45 chipset support the first generation penryn if i was to upgrade my cpu to T9300?
well i have decided to replace the stock thermal paste on my 5920g, however, i was suprised to see that acer used therma pads intead of thermal paste
im even more suprised to see that there are thermal pads all over my gpu and cpu
heres a rough picture of how it looks like
silver color denotes where thermal pads where installed
the weird thing is that the copper plate of the heat sink only touches the parts of the picture with the orange circle
should i put AC MX-2 on the areas where i found thermal pads or just on the areas where the copper plates of the heat sink touches the core
I have the Acer Aspire 5920G. Since my laptop is starting to get a bit too warm, I would like to know the steps in cleaning the fan for my laptop. I already got a can of compressed air. Can someone please tell me the exact steps to clean the fan?
View 8 Replies View RelatedI have had a 5920G for nearly a year and it runs great when it is plugged in. As soon as I unplug it when it is 100% charged, the battery runs out in like 30 seconds.
View 7 Replies View RelatedAcer 5920G won't charge. When I plug in the charger the light that normally comes on to indicate that it is charging does not light up and in windows the icon that indicates that it is charging does not come up either.
My PC is the Acer 5920G best buy configuration, about two years old and no components are overclocked.
I was using it when this happened, I just noticed that the light went off and then it wouldn't charge when I plugged in the charger. As far as I know all the other components work correctly though it does have poor battery life. I was downloading a large file so I had it running for about six hours straight if that makes any difference.
I've checked the charger itself and nothing came loose. The green light on the charger also lights up when I plug it in so it is probably not the outlet that is the problem plus I've tried it in multiple outlets.
I'm pretty sure its either the battery or the charger, but I would like to know for sure and get advice from anyone else who may have had this problem.
Past few days I got my 8600M GT 256MB DDR2 GPU overheated and it is broken now. Sigh!! The system was still bootable and I did even hear the login sound not until today when I just unplugged the HDD and GPU myself. When I put them back together, I won't boot as usual. It stops loading a while after I turned it on and stays freeze until I shut it off.
FYI, I removed the HDD to copy a backup of my content into another PC. While connecting to other PC, I did change some setting on the Ownership of some folder to get it accessible. As for the GPU, I just simply removed it to take a look myself and snap some photo of it, then inserted it back as before.
So, I wonder will these techies stuff I did awhile back could corrupted the bios that would make the system halted halfway.
Additional information that I would like to share is that I have decided to replace my GPU with ATi Mobility Radeon HD3650 512MB DDR2 instead of the original and did learn the method to do so. Read on some info regarding flashing the GPU, but was not sure bout it.
I tried installing Service Pack 1 and it won't boot. Microsoft has just sent me a Vista Home Premium Repair CD that will hopefully fix it. I have Recovery Discs, but then I'll lose all my data. This is the 2nd time that my 5920G has broke like this, is there a huge design flaw with this laptop?
Is Acer always like this? It was such a high end laptop for its price (8600M GT, Core 2 Duo 1.5 Ghz, 2 GB RAM, HDMI, HD-DVD, for $1099), but I can never trust this company again.
I recently bought an Aspire 5920G with geforce8600M GT 512MB and windows vista premium.
My graphics card takes more than 700 MB from the RAM memory.
I would like to know if there's a way to make it take less or even disable this option?
I have a 5920g computer which I adore, sadly we always hurt the ones we love, I dropped it and broke the right hinge, because of that the plastic frame of the monitor ripped 2. It still works perfectly fine, but its annoying as hell to watch my lappy like this all the time. I called acer, and found a provider who can repair it for 400 dlrs (I payed 1000 dlrs for the lap) so well, its seem outrageous to me paying 40% of the total price for a hinge replace.
Anyway, I found the hinge and the other parts on Ebay singapore, for less tan 100 dlrs. So, heres my question, does anyone know how hard is it to replace this parts, I am a mildy medium kinda handy guy, with some hardware skills. So anyone know if this is hard, is there a guide around that can show me the process, or should I just pay the 400 dlrs and get this thing done.
Ive taken the back cover off my 5920 many times and really never took a look at it until now. What i noticed is that the vents for the ram are covered by a glossy black see through tape rather than mesh, which covers all the other vents.
Ive linked a picture below: add http into brackets
Has anyone else noticed that in their laptop? or is mine the only one where they ran out of mesh and decided tape was just as good. I wanna just rip it off.
Another thing, has anyone been able to overclock their 5920?(mines got a T8100) ive been searching for days and cant find anyone who has. I always have my backcover off and have my laptop resting on a custom dual 120mm fan notebook cooler. My idle temps are from 37-42, load is just over 60. I wanna push this thing just a bit more.
my fan is making a buzzing noise it's really enoying when i record stuff in the mic you can here it very well
View 8 Replies View RelatedMy 5920g start it wont even get to the postscreen happened right after the hdd got messed up.So i changed i figured that it was just the hdd that kept it from starting but nothing happened.So i asked and some told me it could be anything im really hopping its that its just the gcard since its the 8600m gt.One person told me to put a cd in the drive and if its spins it its probably the card and not the motherboard or cpu but idk.So best case if its the 8600m gt, could i upgrade it to the 9600m gt or the 9650m gt since they also are mxm2.
I think the bios support the 9600m gt but im not sure about the 9650m gt.
I really wana finish my fallout 3 game i was almost at the end.
so one of my hdds died on me so I decided to use the one that I was using as an external hdd.
I reformated that HDD, took out the broken HDD and replaced it with the new one.
I popped in the Recovery disc and everything started and was going smoothly until it hit 18% and it gives me this "Restore Failed - reason 0xd000001e"
I know it's possible to upgrade the hard drive in my Acer 5920G, but I've got no idea what type of hard drive to look for, and which will be compatible etc.
View 10 Replies View RelatedSystem:
CPU: Intel t7500 2.2 Ghz
RAM: 2GB 667Mhz
HD: 1 HD 5400 RPM 250 GB
GPU: Nvidia 8600M gt 512 MB ddr2
I got these temperatures by running orthos to stress the cpu, and furmark to stress the gpu at the same time. Are these temperatures normal for an Acer Aspire 5920g? Cause I find these temperatures rather high, and I'm wondering if these are safe. I already have applied some artic silver 5 thermal compound to the both the gpu and the cpu.
I am a "silver surfer" who is starting to enjoy "playing" and "tweaking" my Acer Aspire 5920G on pre-installed Vista SP1 as a little hobby to pass the time
So far I have confined myself to dabbling with software and Vista itself but am now thinking about becoming more adventurous and upgrading the RAM from present 2GB to 4GB.
Firstly, is this a worthwhile upgrade bearing in mind I do not run any particularly intensive applications? In other words will I notice a performance difference in,for instance, boot times etc ?
Secondly, a few months ago I think I saw an article or thread in this Forum explaining how to increase the RAM in a 5920G and containing a couple of very useful diagrams.