Dell :: Latitude E6410 6-cell Battery Sticking Out?
May 21, 2010
I'm deciding between T410 and E6410. I know the 6-cell in thinkpad doesn't protrude but does is stick out on E6410? I really do not want to ruin the dimension by using "physically" extended batteries
I've never had a battery that wasn't flush to the surface before and I'm worried that it will be annoying as hell. Especially when I'm resting it on my lap.
Refurbished Laptop - latitude E6410. The battery light contrantly flashes on the Battery five or Six solid blue lights - Then three flashing lights.In addition, the Light on the Computer ( ) and the desk top icon for the power adaptor cord /battery says" Plugged in - Not charging".I ran the Dell Diagnostics (Fn key at bootup) but it found no problems.is the battery dead?
I've been reading several user experiences and figured I should join since I'm having several questions/issues with my E6400.
For now my issue is with a 9 Cell battery I purchased from fleabay.
I bought a "Geniune New" battery from a US seller. For some reason the BIOS always reads it at 99%, where as my 6 cell will go to 100%. Is this normal for the 9 cell? Also I noticed the LED light button is much harder to press on the 9 cell compared to the 6.
The only part number I could get from the 9 cell is this:
JP-0FU441-47847-917-J6NP-A01
It has all the Dell markings, recycle numbers etc. It even came with a 9 cell Dell booklet. I just wasn't sure if all these 9 cells register at 99%. My old Inspiron E1505 9 cell also registered at 99%.
I have an XPS m1330 (T7500, 3 GB RAM, 8400M GS GPU) and had a bad 6-cell battery that wasn't holding charge.
Dell sent me a replacement, but they've sent me a 9-cell which I don't want b/c it's heavy, adds bulk and most importantly, the angle on the laptop REALLY hurts my wrists... but apparently they won't send out 6-cells as replacements anymore, just 9-cells.
I'm wondering if there's anything I can tell them to get them to send me a 6-cell without having to put my 9-cell on ebay or something .....
I'm looking to get the Studio 1555 and the only thing I'm not sure on right now is which battery to get.
Is it true that the 9 cell sticks out the bottom a little bit? I would just go for the 9 cell, but I use my current laptop on my lap a lot and I'm worried that if the battery sticks out the bottom it would be uncomfortable since the laptop would be resting on two points rather than the entire bottom
I have a Dell Inspiron 6000 for about 4 years almost. I have 512MB but am going to buy the 2GB ram from newegg because it is very slow.
I am also formating my laptop as well as my desktop. Most of the time i use my desktop but for my laptop i bought a charger that was CHEAP and i think it messed up my battery life a bit.
I just purchased a new charger from Dell and will throw away the bad charger i have.
My battery life in my 6000 is about 40 minutes. It used to be 2 hours and 30 minutes when i first got it. A few months ago it was actually 1 hour and 20 minutes. My neighbor has a e1505 and his battery lasts like 5 minutes now so all he does is use his charger.
I see on Ebay from reputable sellers that the 6 and 9 cell battery price is pretty close. 6 Cell is about 44 dollars and 9 Cell is about 48 dollars.
i am having a hard time deciding my configuration for a inspiron 13"
i noticed that the Refurbished laptop have a Great price $609, 2.0 intel core 2 duo,4gb,320gb,6cell,Dell 1395 802.11G Wireless Mini Card.
For that price it seems to good to be truth, but i have no experience with refurbished laptop.
What is causing me confusion is, if i should go for a new laptop that has ,2.0ghz(same cpu), 3gb,250gb,intel next gen wireless N, 9 cell battery for $779, all because the $10 for the wireless and 70$ for the battery and it has a 195$ discount already of the original price.
I have an HP Pavilion dv6000. When I purchased the laptop, I chose a 12 cell battery, and it has a sticker on it that states: Replace with 451864-001. My battery went bad, and I purchased a replacement at the HP Parts Store online. I specifically chose a 12 cell replacement, which brought up the same part number, i.e., 451864-001. However, when it came in the mail today, the battery looks like a 6 cell, as it's about 1/3 the size of the old 12 cell, despite my purchase receipt which states that I ordered a 12 cell and the packing slip which also states that HP shipped a 12 cell. The model number of the old battery is HSTNN-DB32, and the model number of the new battery is HSTNN-DB46. Unless they were able to shrink the 12 cell to make it resemble a 6 cell, I'm pretty sure I received a 6 cell, despite the notations in the purchase order and packing slip. This is a long way of asking, is there a tool that I can install that will tell me how many cells are contained in the battery? The battery, itself, does not state how many cells it contains. If it is a 6 cell, as I suspect, HP will be getting it back.
hey everyone im a new Dell E6400 ATG owner and was wandering what would be a better option for my money? I already have a 9-cell battery and was wondering should I go with another 9-cell or get the 12-cell battery for extending my run time?
My question is this - are SATA laptop optical drives the same as older IDE drives, in that they are universally compatible
with laptops, or do OEMs have drives that don't follow a standardized size and form factor now?
I found a Lite-On DVD-RW with LightScribe on eBay for like $40, but I don't want to get it if it's not going to fit.......................................................
Does the Latitude E6410 have a weak or a time critical signaling on the VGA port? The other day I had to replace my Latitude with a backup laptop as it was unable to drive a VGA splitter feeding three projectors. There was no problems in driving at single projector though. The other LG laptop E500 had no problems in running exactly the same presentation on all three projectors through the splitter.
The rather surprising thing was that as long as my power point presentation were display in edit mode, it worked fine whereas in show mode all of the connected projectors went blank. I tried to exercise the Fn F8 with no change.Would a VGA amplifier do the trick?
My Latitude E6410 Windows 7 Ultimate 64-bit machine crashed yesterday and when it came back up I was no longer able to use the touch-pad buttons below the touchpad, or the middle button above the touchpad. The pointer stick, along with the right and left button above the touchpad are still working properly.
I have tried reinstalled the ALPS driver and the Dell touchpad software.When I open the touchpad software it shows the touchpad as being enabled but it does not show any configuration for the pointer stick or buttons above the touchpad. what driver or application I need to install to get my touchpad and buttons operational again?
My company has offered to give to me my Latitude e6410. However, I cannot keep the hard drive. It has to be destroyed per policy. I am able to pull off recovery information and build my own image. One more concern is that the current hard drive is encrypted with Symantec Endpoint Encryption (SEE). Therefore, I do not want to simply clone the drive as I do not want no cannot use that image.
Also, if I need to reinstall my own image of Win 7 from new disks, will this e641 run 64bit. Currently the OS is WIn7 Pro.What about the recovery partition? I already have a spare 5ooGB 7200rpm 2.5" disk and i have a lot of hardware experience so I have no concerns about the actual disk replacement. It's just the image.
I have one device, a 3DRobotics PixHawk autopilot, which connects intermittently via USB to my E6410. All other USB devices, flash drives, cameras, wireless rcvr etc. always work fine. This one device does not. It only connects occasionally and usually does not. The failures issued by the device vary.
If I hook the device to my Asus X53U, it connects every time. The Asus is extremely slow and I really need to reliably connect to the Dell.
Note: The E6410 contains an upgrade to an i7 720QM quad processor.
We image all our new systems in our organizations on SCCM. I've got one that is a puzzler. I will not get an ip from the server. Instead it displays the message "PXE-E51:No DHCP or proxyDHCP offers were received." No other computer has this issue. I does not get as far as the network boot so it is not a windows deployment service issue. And it senses if the cable is disconnected, and gives you a different PXE error. I have flashed the BIOS, no sucess. I RMA'd the motherboard, and no difference. Dell won't replace the whole system since it was a replacement for another DOA. I thought it might be that little daughter card that contains the NIC connection, but cannot see that listed on the dispatch site as a seperate part.
I bought aDell Latitude E6410 laptop yesterday and every time it turns on it says no boot or something. So I push the enter button and it resets. Then when it shows the dell logo again I press F12 and go to the boot sequence and its set on cd drive and not the internal HDD. So I choose to redo that all over again and then press boot from internal HDD and it works no problem but its a lot to go through just to start a laptop. How can I figure out how to change the admin password so I can set the boot sequence right.
create a new Bios Screen to ours Latitude E6410.I have used a bootable CD with a splash.exe file to load a Bios Screen with the company logo and it had worked in ours Latitude D600/610/620/630 and E6400.Now when I try to do the same with our E6410 I'm getting the message " This Bios does not support splash.exe. Upgrade your system Bios and try again."
Latitude E6410, changed a bad HD for a new one. Installed windows 7. Besides having issues with WIFI and USB drivers, I cannot do a windows update, it shows a big red X, message I get is
" Windows Update cannot currently check for updates, because the service is not running. You many need to restart your computer"
I have a Latitude E6410 with SD card reader. I can see the card reader in device management but the sd card will not apper as a drive in Windows 7. I tried the sd card on a colleagues laptop (exactly same spec and OS installation) and it works instantly.
all I got a new E6410 and 2 docking stations around a month ago.The problem I have is that when the notebook is in my office docking station it is really really slow.I can watch while window contents are draw, switching messages inthugnerbird takes a couple of seconds.In the home dokcing station everything is fine.
I have a Dell Latitude E6410. I recently installed created a linux partition on my HDD but was not interested in keeping it. Anyway after I uninstalled this OS, the space allocated to it on the HDD was turned into unallocated space. I have been unable to merge it with my primary partition. What I wanted to ask was that if I perform a reinstall of my original OS(Windows 7 Professional), will I be able to recover the original partitions and how can it be done?
I bought a Dell Latitude E6410 with fingerprint sensor, I checked the drivers and I've the drivers for Dell ControlVault w/ fingerprint swipe sensor, and I want to use the fingerprint sensor instead of the pasword to log in in my user of the computer, but I dont know what software I need to do it, what software (Aplication) can I use for that?
This one currently has A07, and I know it needs to flash A09 before bumping up to the current A13, but A09 stops right after launch (".....unexpectedly quit..."). Logged in with Admin rights, not seeing any reason for BIOS failure. Another download of the A09 was tried as well.
I just bought an E6410 tonight, thanks to a 30% off coupon I found.
All of a sudden, however, I'm doubting my purchase - specifically because this machine uses an Alps touchpad, whereas the Vostro 3300 I was going to buy (before I found this coupon) uses a Synaptics touchpad.
The last time I had a machine with an Alps pad was in 2004 with my Latitude D600, and that thing sucked. I mean, it was an atrocious piece of hardware.
So what's the verdict on the hardware in the new E64x machines? Is it painful to use? I found a thread talking about using different OEM drivers to improve the responsiveness of the device - is this still necessary?
Just curious to see what current owners think about this. I still don't understand why Dell's been so dead-set on using Alps hardware since the D-series. My old C600 had a Synaptics trackpad, and I loved that thing.