I recently downgraded my girlfriends Acer Aspire 3680 from Vista to XP as it became apparent that this notebook couldn't handle vista well; (on a side note, this is the second aspire 3680 that I have downgraded). For some reason no matter what I do the computer does not see the internal dial-up modem. Now, as its internal there is no installation disc, I have downloaded 6 different acer aspire 3680 modem drivers from Acer support centers and not a single one worked. In the Device manager, the modem drop down is not even there. I ran the modem troubleshooter and it detected no port was found, but Ports weren't in the device manager either. This one is really stumping me and i'm tired of looking at that screen.
I've recently bought my E6500. My configuration has no dial-up modem inside. (it's impossible to order custom config in my country). This thing is not very useful nowadays, but sometimes I need it to send faxes.
My laptop has RJ11 phone line connector and corresponding 2-pin connector inside, so it should be possible to install Conexant D330 modem module, which is available cheap on eBay.
But there is one problem: I also need the orange flat flex-cable with 10 pin connector. It's shown in the E6500 service manual modem page, item #3 on picture. Right above the WWAN card. (sorry i have too few post and can't add the link, you can find it in e6500 owners lounge thread)
Can somebody remove back cover from your E6400 / E6500, and tell me the Dell part numbers of the flat cable and modem card?
ACER ASPIRE 3680 is the laptop am using,i would like to know can we upgrade the RAM and wht is the maximum RAM upto which we can upgrade? and will it support windows vista if i upgrade the RAM
My laptop wont turn on at all, no lights at all. The power supply is fine, and I opened it up and found a few burnt capacitors. Ive searched on ebay for Aspire 3680 mobo but all have different model numbers to mine. My model number is DA0ZR1MB06D1 REV.D. Also on the RAM socket it has another number which is MBAZL060017090E53B2505 and below that it has 31ZR1MB00I0. I cannot find one on ebay with the same numbers as above. Will it make a difference if I get one which has a few numbers/letters which are different to my current one?
I recently picked up a 3680, upgraded to a 320GB hard drive and switched to xp from Vista. Runs great but the speakers sound like they are down in a well literally. Could it be the drivers or do I need to replace the speakers? Anyone else have this problem? The reason I believe the speakers are ok is when I use headphones it sounds the same.
I Bought and Xp Disk but, It doesnt detect my harddrive (Classic Sata Problem)
So I hear there are two ways to get around this...
1.)Change AHCI in Bios, which doesnt work for me because my laptop doesnt seem to have this Option in Bios, so thats out...
2.) And Slipstreaming which I have found drivers that people have refferred to other people but I dont quite understand how they work...(The tutorial I was reading and the drivers I downloaded didnt add up)
So I was hoping someone could give me specific instructions( for my model) for either of these methods to install Xp (Spent lot of cash on the disk dont want it go to to waste)
Basic issue is that all of a sudden the touchpad has stopped working and that little icon that was in the systray has dissapeared. it was working fine a few weeks ago. i currently am using a USB mouse, but i need the touchpad at uni as the desk space is very limited. its a shame this issue has came up now a day before a MAJOR assesment is due, and i cant finnish it because i cant use the mouse at uni.
Anyways, so i have tried the FN+F7 thing, doesnt work. Tried Re installing and rebooting the drivers, still doesnt work. tried a system restore to when it was working. still doesnt work i have basically tried EVERYTHING mentioned on various forums and on google. nothing seems to work. the drivers appear to be installed but wont work for some reason. i will attach photos to the main options so you can see how it appears to me.
there are no bios otpions i looked for those. seriously its so weird, nothing works and its very frustrating! in the past few weeks i have installed adobe illustrator CS3, dont know if that could be the reason for it not working, but i dont think so. I have windows XP SP2. when i try installing the original drivers off a backup cd my dad made, it just installs and does nothing. i downloaded the newest drivers from the website and still the same thing. the program does appear in the program files, and the control panel/add remove, but just doesnt seem to run!
overclocking the Intel Celeron 440 Processor on the Acer Aspire 3680. Here is a screenshot:
As you can see, I overclocked my friend's Acer Aspire 3680. The Celeron M 440 went from 1.86ghz to an amazing 2.35, for an increase of 490mhz! Now, this is definitely not going to be the most safe overclock, and it will consume a lot more power and heat up much quicker, but it is just to show how much you can overclock the Acer 3680.
Here is how I did it:
1. Download CPUCool. (Costs $18 to save your stuff, otherwise it won't for the shareware version)
CPUFSB did not work for me but it may work for you. It is free. Try it
2. Install CPU Cool and say yes to a desktop shortcut and running under windows start up. Now, restart your computer as it tells you too.
3. Go to Functions, change CPU FSB, and then select I don't know. A PLL drop down menu should show up.
4. Make sure it is ICS on the left. Then, go down and choose 954310 all the way at the bottom. Click fine tuning, click ok, and then it should show your frequency. If it doesn't show 1866, and a number less, then download Rightmark CPU Clock Utility and select throttling under profiles and set it to 100%. Unforunately you can't change the voltages.
5. Click fine tuning in CPU Cool, now it should show 1866mhz. Just add 60, 10, or .10 or so mhz by click + 60, +10, or just +. I recommend 2000mhz for the best balance of speed, power, and longevity.
6. Check both boxes as the right under Tray Frequency 1. Click set frequency, ok, and then minimize to tray. Do not close, because your clocks will be reset!....
Notebook was brought to me dead. Meaning it will not start, no fans come on nothing.
I was told to keep it because of cost of replacement board.
So I have been reading in these forums that the motherboard might/can be change for a different one, other then the original(MB.TEB06.003). Like to know if this can be or has been done.
Also, if not can this mobo MB.TEB06.003 handle a duel-core cpu/
I just bought this new acer 3680 1 month ago because i needed a laptop for my studying. basicly all i need it for is to take notes from classes, and surf the web (youtube etc). ok so basicly the first impression with preinstalled vista was horrible. incredible lag... 3 seconds delay at all times when browsing the web. and completely unable to playback any form of media with any other windows open without the sound lagging like crazy... all that kind of stuff
but the main problem seems to be the fan. It runs at high speed (producing as much noise as my desktop computer). The fan turns on aprroximately 4 minutes after you turn on your computer, or immediately after you open an application.. and it just keeps on running untill you turn off your computer... It is so annoying that i have trouble bringing the computer to class (which is where i really need it!) because i feel embarrased about the noise, and frankly i think this is an annoyance to the other students aswell. Is this a common problem with 3680? No one of the other students pc's fans run when they just use basic applications like word, or internet explorer, and they certainly dont do it when simply idling on the desktop.
furthermore it needs to be said that i have messed around with vista alot, and tweaked it in every possible way to remove pressure of the cpu.. and ofc removed all antivirus programs etc. Furthermore i tried installing XP, and guess what.... it took 5 mins of idling on the desktop in the brand newly installed xp for the fan to start again!!! so i conclude that the problem is not caused by vista overloading the cpu!. Does anyone else have this problem with their aspire 3680? maybe im just overly sensitive about the noise, but really it isnt supposed to run at all times.
I turned on the machine today and instead of the windows login page I was presented with a black screen with many strange characters. I dont understand what happened
I have used the GParted cd on this machine so I put that in and it crashed too.
My husband dropped his Aspire 3680-2682 the other day and the screen went wonky. I booted it off a VGA monitor and it seems to be fine running from there, BUT I could not get it to boot to VGA except in safe mode, and when I choose to boot in regular mode it goes to the LCD screen and doesn't allow switching the display to the external monitor.
This is the only thing that concerns me that it might not be just the screen that sustained damage.
I was eventually able to get th bezel off (it doesn't come 100% off on this model but doesn't need to) and remove the lcd panel for inspection. The thin board taped to the back of the panel doesn't seem to be visibly broken or strained and the connectors to it were taped so firmly in place they didn't budge on impact. The small board that rests at the bottom of the top case under the bezel (the inverter?) can't be inspected well and I don't want to damage it by trying. In any case nothing appears damaged to the naked eye on or around the screen.
The first pic is how the screen looks when booted; it also (visibly) flickers and redraws continuously. The second shows that applying pressure allows a clearer view of the console and stops the flickering.
[url] [url]
I have found a replacement screen online for 50.00 and feel comfortable enough trying to replace it rather than spend the cost of a new laptop on sending it for repairs.
However, if it's not just the screen I don't want to throw more money at this.
In your experienced opinions, does it look like the damage is typical of a broken LCD screen and not something in the motherboard? (no clue on how to get a closer look at that stuff. took every screw out of it last night and couldn't get the bottom case to reveal its secrets.)
it is a Acer Aspire 3680, the other day the clips that holds one stick of memory in broke, does anyone know how I could fix this, was thinking of gluing the clips back on or using electrical tape to hold memory in place,
My brother just bought an Acer Aspire 3680.He purchased 1 gig of DDR2 Memory from Crucial. When we get to the desktop the screen is fine at first then the screen goes off and back on with 8 bit display. 512 DDR2 came in the machine. Crucial site said he could mix memory sizes. I tried it with the 1 gig stick by itself in case the mixed memory was the problem. Same thing..I've tried 2 sticks of 512...same thing. I've tried 2 sticks of 1 gig each..same problem. This laptop won't allow any upgrade at all. Will only run correctly with (1) 512 stick. I've never seen this problem before. I've installed many memory sticks in computers. This is a first for me. What could be causing this?? Any advice would be appreciated. BTW. the computer shows the upgrade amount of memory but the display color keeps changing to 8 Bit! I change it back to 32 and it reverts back after a few moments to 8 Bit. I went to Acer and installed an updated driver for the Intel Graphics card thinking the driver would help. I haven't installed a bios update yet. Called Acer and they said to return it for repair.
My high school-age son was working on an English paper when something fell off a shelf and whacked his Aspire 3680 right above the hard drive bay. It started clicking and finally crashed.
The computer won't run with the hard drive installed. It makes nasty clicking sounds trying to boot, and finally beeps and powers off. Without the hard drive, the laptop powers up and runs BIOS just fine.
We can buy a new hard drive, but it seems awful to pay Acer another $20 + $10 shipping for the Vista restore disk!
My aspire 5315 over heats occasionally and when i am using it it shuts down due to heating problems. I use "notebook hardware control 2.0" to monitor my hardware, and at time it shows my cpu temp to be 98 degree centigrade, at 99 it shuts down.
So what im asking that is this a normal issue, do you guys owning this model have this problem as well.
Today i used "Speedfan" to find out any info about my cpu fans, but it gave me no info, like no fans found.
Can some one install this app in their aspire 5315 and tell me if u get the same results.
edit: k even if someone else does not have this app or does not want to install it. i stilll find it a bit odd for a laptop to be with out a cpu fan, dont u.
like this is how the normal operation of speddfan should look like, " i ran it on my desktop pc"
Just got an acer aspire 15 for birthday. The box says dvd/cd combo, but there is no dvd cd drive. There is a plastic piece over where it would go. Can I add one and how much for and internal one?
on my installation of an internal bluetooth adapter (I bought off of ebay) in my Aspire 6930? What exactly do I have to remove to get to where I install it? Where do I install it?
I've just bought an Acer Aspire 5920G and the Crystal Eye webcam works perfect with MSN and so does the internal microphone. However, I've started hosting a show on an Internet radio and the sound quality from the internal mic is too low. Therefore I bought a microphone that I plugged in the appropriate jack on the laptop (next to the jack for the headphones) but when recording or broadcasting it seems that my laptop uses BOTH the external and the internal mic. Could anybody tell me how to DISABLE the internal mic and use the external instead?
I've tried to disable the Crystal Eye from the Device Manager on Windows Vista but that doesn't solve the problem. I've also tried to modify the settings from the recording devices but the LineIn is not plugged in. I'd just like to plug a mic and use that instead of the webcam's one. Any help would be really appreciated as I have to host a show in 2 days and I don't have a clue on how to solve this problem.
My uncle bought a Aspire E1-572-6870 series notebook six months before for me from USA. After using 10 to 15 days I noticed the internal speaker is not working. But the headphone and/or microphone is working very fine. I went to a local laptop repairing shop for diagnosis. Unfortunately they were unable to find out the actual problem. They suggest me to change the speaker chip may result solve the problem. Before changing the chip I want to diagnose once more for accuracy about the problem. Any online check can be possible?
I have an acer aspire 5630 laptop which I bought in October. Now I had to repartition and reinstall windows vista for some unavoidable circumstances. But I have lost all the softwares like NTI CD/DVD maker and drivers like modem. I do not know what the problem is but my dial up modem does not work. It shows something else in the modem list (Contexant) that is different from what was there originally ("HD audio"). Whether the telephone line is plugged or unplugged it shows the same error message. I mean the error message like no dial tone is shown while no telephone line plugged. Besides it does not produce the speaker sound even after enabling so which it used to do before.
Moreover, now as I have lost the softwares like NTI CD/DVD maker, how can I reclaim them as my warranty has not yet expired. (the driver is not in their website)
The internal IDE port got fried and cannot be recognized by the laptop so I came up with the bright idea of installing an OS on a USB drive and booting from that.
XP appears to be the only OS that will install onto an external drive. But, when booting with XP, I get a BSOD..
VISTA won't install to a USB drive so I installed VISTA on the external drive using a workstation, but then when I tried to boot up with the laptop, it got the solid B/W bar at the bottom and just sat there.
Is there any option to boot an ACER 3680 with an xternal drive?? Or is this laptop now useless?
i have na acer 3680 and it came with vista but i got rid of vista and put xp on it i have all the drivers working the only problem im having is the button on the front to turn on and off wifi will not turn on the orange light will not go on i do have wireless internet
My daughters Acer 3680 just stopped working. I purchased a new AC adapter and it still doesnt turn on. The battery is new. Im guessing its the power jack that needs replaced. To avoid soldering Ill purchase the whole DC/USB board
[url]
I need step by step instructions on how to dissasemble the notebook. I got it mostly apart but i just can seem to separate the thing in half to access the DC/USB board. Any online resources, videos, manuals that would show this process of dissasembly?
I found a post on here with the identical problem. The post pointed to a Utube video that showed the process...that video has since been removed....heres the old post Acer Aspire 3680 dis-assembly
