Dell Inspiron N4010 :: Can't Get To Boot In Safe Mode
Mar 8, 2013
I start the laptop and I get the black screen with the Dell logo on it. There is a progress bar at the bottom that moves across to the right as the boot up progresses. In the bottom right corner, it shows the option of hitting F2 for Set Up or F12 for Boot Menu. I can access both of these menus. It then progresses to a screen with the Windows logo with the words "Resuming Windows" underneath. Once that completes, I get a black screen!
I was told that I should boot up the laptop in safe mode by hitting F8.....
I can't seem to get this to work.
View 7 Replies
ADVERTISEMENT
Feb 14, 2013
I have Dell N4010 laptop with 4GB ram (1333 Mhz, 2X2) purchased in Jan 2011. Recently I bought transcend 4GB 1333 and have removed existing 2GB ram and replaced with 4GB to increase the physical memory to 6GB. I can see that the ram has been detected and the total is showing up in Bios. After this, the system does not boot, it just keep restarting.
I tried to start with safemode, however the files load but at the end, I receive a blue screen with error like '...Bad pool header...'.
OS: Windows 7 x64
Bios version: A13
View 8 Replies
View Related
Jan 27, 2015
I was trying to boot in safe mode so i went into boot options checked safe boot and minimal. Then when I restarted, it just kept restarting over and over again. I can't get to safe mode. I can get to the setup and boot manager. I tried running diagnostics and there were no errors.
View 3 Replies
View Related
Jun 13, 2014
HP Pavilion g6 Product ID : QB582UA#ABA
Memory test: passed
Smart check: passed
Short DST : Failed
Failure ID : 6C0G9G-6AX502-MFGH5G-60SA03
Hard Disk 1
Run-in-test : FAILED
My laptop will not boot. Unable to boot from disc or into safe mode.
View 3 Replies
View Related
Feb 8, 2013
I have a Yoga 3Pro.... I booted into Safe Mode and now ever time I boot up it goes into SF without me hitting F8? What's going on? It's on my Y3P. What box did I click to cause this.
View 5 Replies
View Related
Oct 30, 2014
I have a Dell Inspiron 15 320gb hard drive that I purchased in August 2013. It has been a great computer until last night.
I shut it down and later rebooted it.
It seemed normal until the wallpaper ( a photo of mine ) appeared as normal. The date and time was showing along with signal strength and battery strength.
None of my short cuts appeared and none of the keys on the key board work - at all.
I tried rebooting and hitting F8 to go to safe mode - nothing.
I tried a memory stick and a SD card but computer will not recognize anything. I would go back to all factory defaults and lose my files if I could get access.
View 7 Replies
View Related
Dec 29, 2014
My Inspiron N5050 no longer boots up, not even in safe mode or "last known good configuration." Decided to reinstall the Operating System, but need to know whether I have 32 bit or 64 bit.Have all the originbal documentation, including system specifications, but cannot tell whether my laptop is 32 bit or 64 bit.How to determine if you can't boot up the system?
View 3 Replies
View Related
Mar 7, 2013
Vista Home Premium, didn't have a disc so ordered one from Dell. Upon startup it ask me to put a disc in to repair.
Will this work, my understanding you needed a Vista disc, and this computer does not seem to have a partition with Vista on it, for the repair. I wondering if this will work? I tried diagnostics everything seems fine, but it loops to safe mode.
View 1 Replies
View Related
Jan 4, 2013
The screen does work in "safe mode", so the screen is functioning. It might be something with the graphics settings (I use a separate screen on this computer often). Step-by-step procedure to run in safe mode to check out the problem?
View 6 Replies
View Related
Jan 31, 2013
I own an Inspiron N4010 14R dell laptop. When I restarted my laptop yesterday, i couldn't boot into windows and windows logo was rotating forever. So I thought OS was curropted and tried to reinstall OS. But it also didn't work. I couldn't able to install OS. But I could able to delete a partition and refresh it.
Then I ran a diagnosis on my computer and it showed an error code 2000-0146. (saying HDD needs to be replaced)
I called Dell support center and asked them about the issue. They said my hdd nedds to be replaced. So I bought a new 2.5" SATA seagate hard drive and installed it in the system.
But even after that, the same problem exists. But this time Diagnostic doesn't show any error. My warranty period is void.
View 1 Replies
View Related
Nov 20, 2009
I am notebook user with a Dell Inspiron 1720 (ich8m) and have a sata mtron SSD (16gb) running.
The SSD will not exceed the 84 MB/s read speed in normal mode but in safemode the SSD reaches 98 MB/s or more. I am now running XP but this problem is also in Vista.
On my old desktop with a nfore 4 the ssd always reaches the 98 MB/s even in normal mode.
The maximum speed of the SSD is 100 MB/s ......
View 3 Replies
View Related
Feb 23, 2008
My 9300 has an issue that I'm hoping someone can help with.
When I boot as normal into XP there are broken lines on screen like electrical interference and then when XP tries to start the screen goes black.
When I boot into safe mode the screen is fine but obviously not at 1900x1200 resolution.
I've noticed my graphics card fan is not spinning so I'm assuming the card wont run at 1900x1200 when it senses the fan has died ?
View 14 Replies
View Related
May 12, 2014
I entered Safe Mode in my Envy TS 15 running windows 8.1 to fix some issues with my Norton software and now I can't figure out how to exit back to normal mode. Internet is shut off in safe mode (even though I selected safe mode with networking) so I can run any of Support resolutions. How to do this?
View 7 Replies
View Related
Dec 24, 2014
The laptop goes into a restarting mode, which after computer loaded the desktop and taskbar keep on restarting itself. Cant click or do anything in it.
I tried to use F8, it wont bring me to the sttandard loading option.
When i bough t it, no manual, no dvd or anything.
View 3 Replies
View Related
Aug 1, 2014
Lenovo Thinkpad Edge E545 with Win7.
I can't get Safe Mode by pressing F8.
Is this a known bug, or is something wrong with my brand-new laptop?
View 1 Replies
View Related
Jan 28, 2015
I have got a new tablet and before I could download any spyware etc a virus has got me ! Its called Ransomware Ukash and i`m completely locked out. it`s windows 8.....
View 1 Replies
View Related
Mar 16, 2009
I found a trojan that is attached to skype.exe. I have tried to start in safe mode pressing F8 on start up but I am not able to access safe mode start up. x201....3249-CTO....i7....4GB RAM....64-bit OS....Windows 7
View 9 Replies
View Related
Jul 20, 2014
I have an HP Pavilion DV6 Notebook PC. The other day, it crashed and gave a blue screen error. Since then, it wont start. Ive tried starting it normally and in safe mode, neither work. This is the information given in the blue screen.:
win32k.sys
PAGE_FAULT_IN_NONPAGED_AREA
Technical Information:
***STOP: 0x00000050 (0xFFFFF901C066263C, 0X0000000000000000, 0xFFFFF9600006CCA3, 0x0000000000000005)
*** win32k.sys - Address FFFFF9600006CCA3 base at FFFFF96000000000, Datestamp 53c5df64
When it first crashed, I was playing a game, then the screen got all pixelated, then the blue screen. The computer has had overheating problems because the fan doesn't work 100%. It would shut off often from overheating, but I cleaned the vents out thoroughly, and it hasn't overheated since then. Since the computer wont start, I cant get to the crash dump files.
View 8 Replies
View Related
Oct 16, 2014
I purchased my daughter an Aspire One 725-0687 last Christmas. She only used it a couple months and it has sat around for the past 5 months with no use at all. She went to use it today and couldn't remember her password. I tried several but continue to get the same response... "Your PC is offline. Please sign in with the last password used on this PC". For some reason, it's not connecting to wifi, I have removed the battery, I have attempted "safe mode" with Alt f5, f8 and even f10 and I get nothing except back to the sign in screen. I tried ALT, CTRL, DLT and it does nothing.
View 1 Replies
View Related
Oct 22, 2012
I received my Dell Inspiron 15R - 5520 laptop and am attempting to set it up to perform a UEFI boot to a Windows 7 (64 bit) installation. I am using bios version A11 which is the latest available.
If I use legacy, I am able to boot fine to the Installation DVD and install/use the system. If I use UEFI (non-secure boot), it will freeze during the boot process for a long period of time. I do not ever get to the GUI to attempt installation. I have tried clearing the disk partitions using diskpart -> clean to ensure it is not due to having GPT vs MBR and have also tried changing the SATA adapter to ATA vs AHCI.
Alternately, I am able to boot to, and install Windows 8 RTM in UEFI mode.
Before I get a lot of responses of "Don't use UEFI", the reason I purchased this laptop was for the purpose of dual booting between windows 8 and windows 7 for development purposes, and require the use of secureboot to properly test the software I am developing. If this laptop is not able to run Windows 7 in UEFI mode, I will need to return it and select an alternate vendor.
View 15 Replies
View Related
Mar 31, 2013
My Dell Inspiron 1764 laptop will not boot up after using windows 7 installation disc in repair mode, as it has to restart several times during set up, it would not restart after first phase of operation. It never got to finish operation. Now it is just coming up with a black screen saying, Windows boot manager
Windows failed to start. A recent hardware or software change it might be the cause. To fix the problem:
1. insert windows installation disc and restart computer (which it will not let me do)2. choose your language settings and then click next 3. click repair your computer
if you do not have this disc, contact your system administrator or computer manufacturer for assistance
file: BootBcd
status: 0x000000f
info: an error occurred while attempting to read the boot configuration data
After start up even pressing F8 before logo disappears numerous times it will not let me into that menu, so I cant access start up in safe mode or last known good configuration. No matter what I do it will not go past the above message on screen.
View 3 Replies
View Related
Mar 31, 2013
My Dell Inspiron 1764 laptop will not boot up after using windows 7 installation disc in repair mode, as it has to restart several times during set up, it would not restart after first phase of operation. It never got to finish operation. Now it is just coming up with a black screen saying, Windows boot manager
Windows failed to start. A recent hardware or software change it might be the cause. To fix the problem:
1. insert windows installation disc and restart computer (which it will not let me do)2. choose your language settings and then click next 3. click repair your computer
if you do not have this disc, contact your system administrator or computer manufacturer for assistance
file: BootBcd
status: 0x000000f
Info: an error occurred while attempting to read the boot configuration data
After start up even pressing F8 before logo disappears numerous times it will not let me into that menu, so I cant access start up in safe mode or last known good configuration. No matter what I do it will not go past the above message on screen. I do have 1 year left on my warranty
View 1 Replies
View Related
Jan 2, 2015
I am trying to find a solution to repair a Vista (Home?) installation on an Aspire 5920. The laptop blue screens with a Stop error code 00000F4 when booted in either Normal and Safe Mode. This problem started after installing a program although it may also have a malware/virus problem. The inbuilt Startup Repair and System Restore both fail.
I have the Acer Recovery disks but the Acer eRecovery website suggests that all personal data will be lost if they are used. Is it possible to repair the OS installation from the recovery disks instead of reinstalling it?
View 4 Replies
View Related
Jan 9, 2015
I have a Dell inspiron n4010 that will not power on, the battery light flashes on for a couple of seconds when I plug the AC power adapter in, and then switches off. The laptop does not respond when I try to power it on.I have tried unplugging the AC power adapter, holding the power button down for 20 seconds and plugging it back in - that did not do the trick either.
View 4 Replies
View Related
Feb 17, 2013
I have a year old Inspiron N4010 that as of this morning will not power up. Until that time the charging lights and battery were all indicating the batrery was fully charged and everything was as it should be. This morning when i went to power up there were no lights, the laptop made no sounds....it was dead.
I have checked the power transformer and cord and it has a green light and power. I have taken the battery out and tried to power up. I have taken the battery out and reseeded it. Nothing is working.
I cannot try disabling the touch pad using the key to the right of the F12 key.
View 3 Replies
View Related
Aug 16, 2012
Recently, I found that there is some faults with the fan resulting in shutting down randomly. Then, after 2 months that the problem start, the laptop would not turn on although if it is connected to the power. When i press the switch on button, NOTHING would happen.
View 2 Replies
View Related
Jan 5, 2015
I went to get onto my laptop yesterday evening and it wasn't picking up any wifi. I did the trouble shoot and it said to connect to an ethernet cable. This has never happen to me before and I don't know what to do. Today I did a system restore to a few days ago when it was working just fine... nothing happened.. I tried to press the button on the keyboard to turn the wireless adapter on and that didn't work either. I really need this computer at least for a couple more months for my school work.
View 2 Replies
View Related
Mar 5, 2013
I bought Inspiron N4010 laptop 2 years back and i am happy with it till last week.
Last week when i tried to power on my laptop it is not getting started.
I showed it in a nearby harware shop and they said it has board problem.
Will the board gets damaged for just 2 years or is it something else. What to do whether i have to really replace my mother board or could be other reason.
View 3 Replies
View Related
Apr 25, 2013
My dell inspiron N4010 are webcam are not working.
View 1 Replies
View Related
Dec 11, 2014
I have an inspiron n4010. I replaced the battery and it worked for a couple of weeks. But now, it won't turn on or stay on if it's not plugged in. And I can't have it plugged in all the time. It says that it's plugged in but not charging.
View 5 Replies
View Related
