Is it normal for the power brick to get hot? When I say hot I mean, it's so hot I'm afraid to leave it plugged in and go anywhere. I just got my system the other day but really haven't messed with it so far (except for making sure everything was up to par.) Today I started getting into everything, clean install, etc and I noticed like after 10 minutes of it being plugged in (120 watt brick) the brick was so hot it felt like my heating pad on high. I've never experienced this before, is this normal?
I have two power bricks for my notebook (I bought a second one at the time I placed my order so I would have a spare for traveling, etc.)
One of the bricks gets way hotter then the other. I don't understand why, they are both 120W adapters. I can't help but be paranoid that something is wrong with the one that gets really hot and I'm afraid to use it. I mean why would one barely get warm and an identical second one gets hot?
I guess I spoke to soon about my system being perfect (except for the hard drive cover issue that has now been corrected.)
My keyboard is kinda strange. The keys from the middle of the keyboard, all the way over to the right are good and feel solid...even the housing the keys sit in is very solid. HOWEVER...
From the middle of the keyboard all the way to the left side of it when I type the housing that the keys sit in is not solid...it has 'flex' to it...and is actually quite loud when typing in that area. Is this normal or do I have a bad keyboard? God I can hear it now "please return your system to HP to replace your keyboard"...
I'm sure it's very easy to remove it and change it but they will insist that I send it in. Why can't they be more like Dell when it comes to parts that are easily user replaceable?
how to do a clean install and to backup the swsetup folder and to create a set of restore disks just for the hell of it and all of that...so that's not really what I need assistance with.
I was wondering if someone wouldn't mind listing all of the drivers & software that I need to reinstall after the clean OS install is done so I don't miss anything and also the order in which they are to be installed. Why am I asking this? Because this is my first HP, I've always had Dell's before and I realize HP has some other software for like the hard drive protection and stuff so I'm not very familiar with it.
I wasn't able to order my system with a blu-ray drive as their is a global shortage and it was only being offered on the DV8T...which is just way to big for me. HP says they put comments in my file/account that state when they get blu-ray drives in that they will either swap the drive out for me or give me a new computer because of the inconvienence. Now I'm not holding my breath on that but in case that doesn't pan out...is there anyway I can buy the HP blu-ray drive myself from somewhere online and then get it swapped out on my own? I would of course want it to match my machine, I wouldn't want to just get any drive. Also my video card is the GeForce 320M but from what I've read this supports blu-ray as well, yes?
As most of you know there is a blu-ray drive shortage globally so when I configured my system last week I could only configure it with a lightscribe supermulti dvd/dl drive. However there is a quickship model that comes with a blu-ray drive. Is there anyway for me to purchase the HP blu-ray drive by itself and swap it out for the one I had the system configured with in the future when the drives become available again? I would want it to match my machine so I don't wanna do it with some other brand...it has to be the HP drive that would match my system
I keep getting an error message telling me that my hardware doesn't meet the minimum system requirements to install the software...which makes no sense! I've already installed the Intel chipset driver and the intel rapid storage driver AKA matrix storage driver. These two must be installed before installing the ones that are refusing to install.
I called HP, got India and the guy insists just because the driver is listed for my product doesn't mean it needs to be installed. I just kinda laughed it off, he was useless.
So I did a google search on the problem and it seems a lot of people are having the same problem getting these two drives to install-same error message and everything.
any info on IF they really need to be installed and if so, how the heck do you get them to install already?
2.) Intel management engine driver (listed on HP's website for my product but not on this site for the thread devoted to my system and driver installations ([Drivers] HP dv6 Gen 2 / dv7 Gen 3 / dv8 / HDX16 / HDX18 (INTEL))
I keep getting an error message telling me that my hardware doesn't meet the minimum system requirements to install the software...which makes no sense! I've already installed the Intel chipset driver. This must be installed before installing the ones that are refusing to install.
I called HP, got India and the guy insists just because the driver is listed for my product doesn't mean it needs to be installed. I just kinda laughed it off, he was useless.
Just got one of these, and the power brick is well erm.. a brick!
I need / want to get a third party one that is hopefully smaller, so does anyone know of one suitable? or, if not.. know of what i should be looking at to try and find one?
The right speaker in my notebook is louder then the left one is. The only way to compensate for the problem is to lower the "balance" in the sound properties for the right speaker (I have it all the way down to 70 if you can believe that!) Now my audio sounds even between the left and right speaker. I think it's ashame that seems to be the only fix for the problem. Not sure if this is a driver issue or a hardware issue.
NVidia installs audio drivers to the computer when installing the video drivers (which I still don't understand why...I thought NVidia was a graphics company?) Then I install the IDT drivers/software afterwards. HP has verified that this is correct so everything on my end is up to date...minus of course offical drivers for the 320M video card that everyone is still waiting on!
I have been looking online and getting mixed results regarding buzzing noises from ac power adapters. My old hp dv6000 laptop powerbrick did not make buzzing noises as loud as my new dv6-1235cl from costco.
I noticed that a lot of people now hear buzzing noises from their ac adapter. Then I came onto this website.
[url]
Is this a bunch of bs or are they for real?
I can hear the buzzing noise when I put my ac adapter on the table, but almost non existent when its on the ground. I want to know if this will be a fire safety hazard in the future? I dont want my house burning down even when this thing is plugged in.
there both quad cores, heres the links for both. please help me decide on a quad core q9000 or quad core I7-720QM. these are the 2 im looking at : links:
[url]
or
[url]
So im looking at one with an 18.4" screen an one with a 17.3" screen. one has blu-ray burner and one no blue ray. one is q9000 quad an the other is i7 quad core. i don't know which is best.
I would like to bring this to attention for the community, as it recently happened to my SXPS1647. This happens with the 90w brick and only on certain firmwares. The proc in my system is the core i7 620m.
One night just before bed i closed the lid on my laptop to put it to sleep and then turned off the TV, but then i heard a strange high pitched sound coming from the laptop area. I went back and investigated and there was a strange sound coming from the power brick. The best way I can describe it is the sound of electricity moving, a wave like sound that gets higher and lower pitched. Very concerning, so I call Dell and tell them the problem they send a new motherboard and ac adapter.
The dell tech comes to my house and says that's the strangest thing he has ever seen/heard. So he tries the new ac adapter and same sound so he replaces the mobo. With the new mobo the sound is not present, so im happy. But the computer was throttling really bad so i decided to check the bios with CPUZ and it was A01. I decide to update the bios to get rid of the throttling issues, A05 update went nicely but as soon as I restart the system the magic high pitch sound has returned. The previous mobo had the A04 bios when it was making the sound.
I recently read the whole 90w vs 130w ac adapter and wonder if that has anything to do with this issue?
If your battery is mostly drained and you plug the thing in, within minutes the brick gets so hot that I'm afraid to let it sit on any surface, much less touch it.
I thought it might just be a defective piece so I got a replacement power adapter and it gets just as hot as the other one. Has anyone else noticed this?
So I'm about to get my XPS 1647 today. I don't plan on gaming too much, so I don't know if I'll hit these throttling issues, but..
How do I know if my system is throttling or if its just running as fast as it can? Does the 90W power brick heat up? Is there some system monitor I can check?
Well many people seem to suffer from the dreaded brick Failure, I have had a few go crap, and many of those failures usually were traced back to a broken wire in the DC cable assemly. If you wiggle the cable in the area if the strain relief you can usually hear the crackling sound.
I usually find it breaks in the strain relief - See attached Picture.
Fixing this can be easily done with a few items, there are a few little challanges as well.
1. Soldering Iron & Solder 2. Solder Sucker (removing tool) or Solder Wick 3. Wire Cutters 4. pliers, Small Screw drivers 5. Volt Meter (DVM) 6. Electrical tape
If you see Picture 1 of the plug, I just wanted to point out the typical barrel type connector used in the Dell laptops 6000/6400/9400/M1710 Etc.
There are 3 wires to connect here, The Out side Barrel is the Negative supply, The inside Barrel is Postive, and the inside Tip is a Voltage Sense.
I have added some new Pictures to show the inside of the PA-13 brick.
You can see the three connectoins on the bottom side of the board. The spacing is tight, and you can easily solder across two pads, checking for solder bridges is important
Please note, the spaces are small, and you require good eyes, a magnifying glass would help, and some soldering skills.
After your soldered the new connections careful inspection to check for any solder bridges is required.....
The power supply they sent is not only the wrong wattage rating, it also won't even FIT into my laptop's power input.
I emailed them, and they won't even replace the thing.
"I reviewed your order details and I see that 65 Watt power supply is listed on your order details therefore we are unable to send you the 90 Watt power supply as per
Dell's Exchange guidelines, an exchange could be done for like to like items only."
my power brick making a clicking noise and the LED light sort of flickering in conjunction with the noise. Does anyone else have this issue? I'm not sure it's a problem, but I'm worried that it might be.
I have a Dell Studio 1558 and I have some concern about my power brick. The brick itself makes a light sizzling, buzzing or light crunchy noise which isn't continuous, but is causing me concern. The computer itself, also makes a similar noise when doing stuff like scrolling down a page in an internet browser. Every time I press the down arrow and it loads new images, it makes a brief sizzling noise.
When my computer was brand new I brought this up with tech-support and they gave me a new power brick but the noise never went away. I took a day off work to stay at home and waited for a tech to come to my house so I haven't complained about it since then. It seems to be an intermittent issue, some days its worse than others, and I've had this computer for about 2-3 years now.
Have there been any recalls on the power supplies for my computer? Aside from making a noise, I haven't noticed any decline in my computers performance, I'm just worried about it shocking me or frying some of the components inside the computer!
I just got my new dv7t quad laptop and when i turn the laptop back on from sleep the fingerprint reader is not detected. so when i go to type in my password manually the screen flickers about every 2 seconds and resets the cursor to the beginning so it makes typing my 16 character password a , i usually have to just restart.
Also i ordered a bluray player and installed that into my laptop but the hp mediasmart software wont play the movies. i ended up getting a trial software for 30 days but i dont plan on spending another 50 bucks on software when hp should have software i can use with this laptop.
How does the 1/6 GHz processor stack up against the more traditional core duo? Is it roughly equal to a 2.53 GHz processor? I love windows 7 and might trade my Macbook Pro for one.
This model has customized & quick-ship option. I notice the customized version is fitted with Geforce GT 320m - For i7 processor (no other option), while the Quick-Ship model is fitted with GT230m WITH Physx.
I've heard about Physx before, and I always think it is another component bought separately (at least for PC desktop 1-2 years ago). So, is this Physx processor always present with all Geforce GT230m & 320m series, or does HP actually fit this additional processor as a bonus ?
I look on NVidia's technical specs for 320m & 230m, and Nvidia specifies that they are both Physx-ready. What does "READY" mean here ? Ready to be fitted with an optional Physx feature, or does it mean both have already integrated the Physx into 320m & 230m ? ...or do I misunderstand something ?
Realizing that my computer is now a little over 2.5 years old, I had a little time to think about whether I should even think about going over to a brand new notebook. Given the specs of new notebooks these days (and a lot of people know here that I spend quite a bit of time at the HP website/FTP), I was wondering what everyone here thinks about me going for a Quad Edition notebook.
In case you're wondering, I use my dv6500t notebook extensively mainly because I am a UCSD Computer Science/Engineering student who does a lot of activities on the computer both casually and for work, for a good portion of the day, everyday. If I get a new notebook, I plan on using it extensively as well.
The specifications for the dv6500t that I currently use is listed in my sig. It additionally has a 12-cell battery which at this moment can only charge up to 58%, and a rather broken left TouchPad button. Warranty is pretty shot at this point, since I had the 1-year standard (which I have no regrets with).
Now, the Quad Edition notebook that I was specifically looking at was the pre-customized HP Pavilion dv6-2190us notebook:...........
how hot can my hp dv7t quad get. I have the 4 cores at about 50 degrees c. and my video card is at about 44. Should i be worrying about these temps. I used hwmonitor for this data.
I just wanted to share my experience on undervolting my HDX 18t 1103EA, Intel Quad 9000-2Ghz, 4GB DDR3 RAM, 9600M GT-1gb, Vista x64. After reading and trying the undervolting guide (thanks to flipfire), I couldn't make rmclock to work. Anyway because Q9000 has only 4 multipliers: 6x, 6.5x, 7x and 7.5x and rmclock does not support half ones, I decided to try CrystalCPUID. It can do only three ones and I choose 6x, 7x and 7.5x. I managed to go down to 1.163- stable on all three. CrystalCPUID would not allow any lower than that, although according to Intel Q9000 lowest voltage is 1.050. Strange enough both CPU-Z and Everest show that this the actual voltage when CrystalCPUID is active. Also when it is not active the cpu works only on the highest multiplier- 7.5x. My idle temp didn't really changed- it is always around 48C-55C (no AC in my room). I tried to buy CpuGenie (10 euro is nothing for some extra life on a 1300 euro mashine, but paypal asks for registration and I don't want to register.
I will be receiving a dv6t Quad edition soon. I am planning to replace the original HDD with a SSD. The original HDD will go in a external eSATA enclosure.
Questions/comments:
- Are there any step-by-step guides out there for replacing the HDD?
- I have read in forums that doing a fresh install on SSD is better than cloning your existing drive. Is that correct?
- In case of any issues with the installation on SSD, I can always put the original drive back in.
- If I dont delete the MBR on the original drive, will it create an issue in the external enclosure along with the new MBR on the SSD?
I have a few questions that I need clarification on.
First, is 64-bit ok to get. I've read a lot of articles stating that not many things are 64-bit and that drivers are hard to find, and so on. I believe these articles are a little old but I would like to make sure program running and such is ok.
Second, there are so many processors to pick from. You have the: T4200 (2.0 GHz) T6400 (2.0GHz) T6600 (2.2GHz) P7450 (2.13GHz) P8600 (2.4 GHz) P8700 (2.53GHz)
Choices can be a good thing but it's too confusing here. Is the T6600 better than the P7450?
Third, there are two video cards to pick from: 512MB NVIDIA GeForce 9600M GT 512MB NVIDIA GeForce 9200M GS
Which one is better here? I would think the 9600 but that's just a guess. Seems like the 9200M GS is just now available in 512MB instead of 256MB. So maybe that one is.
Just wondering if this is normal - I'm not exactly sure how many fan speeds there are, but for the sake of keeping this simple, let's say there are 5 (1=off, 2=low, 3=med, 4=high 5=max).
My computer is usually at 2, but I notice that sometimes just watching videos can make my fan go to 3. Is this ok? I know my computer is plenty powerful so it's not that it's struggling. I guess it's because I have powerful parts and they create some heat. But it can be a little annoying for the fan to go one notch higher on something like videos.
