Just got one of these, and the power brick is well erm.. a brick!
I need / want to get a third party one that is hopefully smaller, so does anyone know of one suitable? or, if not.. know of what i should be looking at to try and find one?
How can I get HP to replace my LCD? I really am rather tired of the support hassles!
A few months ago, I accidentally dropped my EliteBook 8530w (and since I knew it was bound to happen eventually, I did buy it with ADP). After I got the thing back (after waiting on the replacement LCD screen to come in stock, I've noticed some odd issues related to the screen:The screen seems to have some permanent "smudges" on the screen -- dark areas, that I can't clean off.The EDID seems to be messed up -- it misidentifies the panel name, size, and available non-native modes.
The old LCD identified itself properly as an LP154WU1-TLC2. It offered 1920x1200, 1440x900, 1280x800, and such resolutions..................
My school recommends[read: buy from them] the FM877ut spec 8530w at 1799.
However looking around online, for less I can buy at FM890UA spec'd 8530w.
Do think a "perfect install" disk image from the school's fm887ut will boot without problem on the fm890ua 'book?
To abrievate, the only differences I can see is the Webcam, a T9600 C2 duo and 4 gb ram vs t8600 C2 Duo and 2gb ram.
my elitebook 8530w seems to boot up slow w/ 64 bit vista. i did a clean install and installed the drivers. Ex. it will say "please wait" for 20 seconds before going to the "welcome" screen. after "welcome" comes up..it does boot to the desktop very fast and is ready to go though. what is causing vista to hang like this at the welcome screen?
My specs
8GB(4gb x 2) ddr2-667mhz memory
qx9300 quad core processor- this thing is a beast!
vista x64
Is it normal for the power brick to get hot? When I say hot I mean, it's so hot I'm afraid to leave it plugged in and go anywhere. I just got my system the other day but really haven't messed with it so far (except for making sure everything was up to par.) Today I started getting into everything, clean install, etc and I noticed like after 10 minutes of it being plugged in (120 watt brick) the brick was so hot it felt like my heating pad on high. I've never experienced this before, is this normal?
View 5 Replies View RelatedI have an HP Elitebook 8530w with Windows 7 32-bit. I did not buy this laptop, it was a gift from a friend. I have gotten recently, just a few days ago. I have not used the fingerprint sensor previously before today. I went on the HP site and went to get the driver for the fingerprint sensor. Here is the link to that page. I tried to install the AuthenTec Fingerprint Sensor Driver but it did not work, it said the installation process was interuppted and to try again later. So I tried again later and the same happened. So I uninstalled and checked to see if there were any later versions. I had not looked to see that the original one I installed from the drivers page was from March 17 2010.
I did some researching around and found version 6.0.100.272 of HP Simplepass (The AuthenTec Driver had HP Simplepass installation included). I installed this version and it worked. I opened it up and it prompted me to enter my windows account password. So I did. I then clicked Set Up Windows Log On and it told me to enter my Windows password again. I did but it didn't work So I tried again... and again... and again... It didn't work no matter how many times I tried. I tried restarting my laptop and changing my account password. Neither worked. So I'm confused as to what could be the problem. I would very much like to use this feature.
I have been looking online and getting mixed results regarding buzzing noises from ac power adapters. My old hp dv6000 laptop powerbrick did not make buzzing noises as loud as my new dv6-1235cl from costco.
I noticed that a lot of people now hear buzzing noises from their ac adapter. Then I came onto this website.
[url]
Is this a bunch of bs or are they for real?
I can hear the buzzing noise when I put my ac adapter on the table, but almost non existent when its on the ground. I want to know if this will be a fire safety hazard in the future? I dont want my house burning down even when this thing is plugged in.
I would like to bring this to attention for the community, as it recently happened to my SXPS1647. This happens with the 90w brick and only on certain firmwares. The proc in my system is the core i7 620m.
One night just before bed i closed the lid on my laptop to put it to sleep and then turned off the TV, but then i heard a strange high pitched sound coming from the laptop area. I went back and investigated and there was a strange sound coming from the power brick. The best way I can describe it is the sound of electricity moving, a wave like sound that gets higher and lower pitched. Very concerning, so I call Dell and tell them the problem they send a new motherboard and ac adapter.
The dell tech comes to my house and says that's the strangest thing he has ever seen/heard. So he tries the new ac adapter and same sound so he replaces the mobo. With the new mobo the sound is not present, so im happy. But the computer was throttling really bad so i decided to check the bios with CPUZ and it was A01. I decide to update the bios to get rid of the throttling issues, A05 update went nicely but as soon as I restart the system the magic high pitch sound has returned. The previous mobo had the A04 bios when it was making the sound.
I recently read the whole 90w vs 130w ac adapter and wonder if that has anything to do with this issue?
If your battery is mostly drained and you plug the thing in, within minutes the brick gets so hot that I'm afraid to let it sit on any surface, much less touch it.
I thought it might just be a defective piece so I got a replacement power adapter and it gets just as hot as the other one. Has anyone else noticed this?
So I'm about to get my XPS 1647 today. I don't plan on gaming too much, so I don't know if I'll hit these throttling issues, but..
How do I know if my system is throttling or if its just running as fast as it can? Does the 90W power brick heat up? Is there some system monitor I can check?
Well many people seem to suffer from the dreaded brick Failure, I have had a few go crap, and many of those failures usually were traced back to a broken wire in the DC cable assemly. If you wiggle the cable in the area if the strain relief you can usually hear the crackling sound.
I usually find it breaks in the strain relief - See attached Picture.
Fixing this can be easily done with a few items, there are a few little challanges as well.
1. Soldering Iron & Solder
2. Solder Sucker (removing tool) or Solder Wick
3. Wire Cutters
4. pliers, Small Screw drivers
5. Volt Meter (DVM)
6. Electrical tape
If you see Picture 1 of the plug, I just wanted to point out the typical barrel type connector used in the Dell laptops 6000/6400/9400/M1710 Etc.
There are 3 wires to connect here, The Out side Barrel is the Negative supply, The inside Barrel is Postive, and the inside Tip is a Voltage Sense.
I have added some new Pictures to show the inside of the PA-13 brick.
You can see the three connectoins on the bottom side of the board. The spacing is tight, and you can easily solder across two pads, checking for solder bridges is important
Please note, the spaces are small, and you require good eyes, a magnifying glass would help, and some soldering skills.
After your soldered the new connections careful inspection to check for any solder bridges is required.....
Had the Studio since Wednesday and its great!
However, the power brick has started to make noises? A series of about 10 clicks in quick sucession repeated twice in a couple of seconds.
It will then go quiet for a while then do it again?
Its also pretty hot, too hot to touch for a while and its hot quickly - in about 10mins from cold.
Should I get a replacement or is this normal?
How do I go about getting it replacd? Sounds like its shorting or something?
The power supply they sent is not only the wrong wattage rating, it also won't even FIT into my laptop's power input.
I emailed them, and they won't even replace the thing.
"I reviewed your order details and I see that 65 Watt power supply is listed on your order details therefore we are unable to send you the 90 Watt power supply as per
Dell's Exchange guidelines, an exchange could be done for like to like items only."
my power brick making a clicking noise and the LED light sort of flickering in conjunction with the noise. Does anyone else have this issue? I'm not sure it's a problem, but I'm worried that it might be.
View 4 Replies View RelatedI have a Dell Studio 1558 and I have some concern about my power brick. The brick itself makes a light sizzling, buzzing or light crunchy noise which isn't continuous, but is causing me concern. The computer itself, also makes a similar noise when doing stuff like scrolling down a page in an internet browser. Every time I press the down arrow and it loads new images, it makes a brief sizzling noise.
When my computer was brand new I brought this up with tech-support and they gave me a new power brick but the noise never went away. I took a day off work to stay at home and waited for a tech to come to my house so I haven't complained about it since then. It seems to be an intermittent issue, some days its worse than others, and I've had this computer for about 2-3 years now.
Have there been any recalls on the power supplies for my computer? Aside from making a noise, I haven't noticed any decline in my computers performance, I'm just worried about it shocking me or frying some of the components inside the computer!
Anyone have issues with these speakers lately. Mine just got back from hp repair and the speakers seem to be no better than before. Tons of static when playing music, tons of static. Most songs are downright terrible, even at lower volume.
View 6 Replies View RelatedAll the problems with 8730w is it the same with 8530w?
View 7 Replies View RelatedI am considering buying a 8530w with a intel x9100 and 7200rpm drive. What kind of battery life can expect from this with power save mode on doing web work or watching a blu-ray disc?
How much time do you get with your 8530w?
how do you like the 1900x1200 screen?
I just picked up an 8530w open box item. It's a great laptop, build is really nice, haven't had any of the issues other people have mentioned. But I can't seem to get the bluetooth going. When I ordered it, the description had this to say:
Wireless details:
Intel WiFi Link 5300 (802.11 a/b/g/n draft 2.0)
HP Integrated Module with Bluetooth Wireless Technology
I thought that meant that bluetooth would be installed. I did a fresh install of windows xp right when I got it, and then reinstalled all the drivers. I even tried to install the HP Integrated Module driver from the web but it during and after installation it said it could find no bluetooth bits installed. How do I know if it's in there somewhere? Should it be with a description like above? Here's a link to the full description:
[url]
my plan is to buy an 8530w and swap out the cpu for a Q9100 Quad Core. Anyway, is there special cooling needed for the quad core? I asked only because i noticed that if I tried to add a quad core on the HP website it requires a 'special' graphics card. This got me thinking that they might have added something for the quad cores that they leave out of the normal ones.
View 10 Replies View RelatedJust the other day, I was using the fingerprint reader in my EliteBook, when it suddenly refused to log me into the pre-boot authentication; I had to use a password, instead. Now, it seems my fingerprint reader has (electrically) ceased to exist -- it doesn't appear in device manager under Windows or in lsusb under Linux, and the option to "Swipe Finger or Choose Token" at the preboot authentication screen. Does anyone know what would cause this? The first candidate I can think of is the motherboard.
In addition, my system has started behaving oddly when resuming from suspend -- most of the time, resuming from suspend results in the laptop hard-rebooting about 1/2 second later, and then loop back to the BIOS logo a couple of times before going on and booting.
My question: do I just have to send it in for repair, or is there something else I can do?
When I bought the laptop customized, HP did not offer the option for a webcam; ideally, I'd really like to just pay them the difference and have them add a webcam while they're taking the thing apart, anyway. Is there any way to get HP to do this? If anything, they could probably just swap the GPU with another laptop (a preconfigured one with same specs, but nvidia), so I'd have the same specs with ATI, and now a webcam.
On regular bases I get a black screen during startup like the HP 8530w didn't finish it's BIOS check to boot into the OS, it will then just hang there until I shut it down and reboot. I believe that this issue is also preventing the comp from coming out of sleep mode as well because I get the same issue at random when the comp has entered sleep mode.
I've got the latest BIOS since Sept. but to no avail, I've tried disabling everything in the BIOS that I'm not using and that didn't change anything either.
I have the HP 8530w and a D-Link DIR-615 wireless router and am trying to make them work together. Using the G speed (54mbit), the network is stable (signal quality is excellent). But when I try the N speed, the situation is different. The network starts working as it should, but when loaded (big files transferred), the network suddenly dies and windows vista can take up to a couple of minutes before it discovers the missing link. During that time, the 5300 AGN still receives packets from the router (10 beacons per second as per setup in the router). But no packets are sent (checking with Intels statistics tool).
So it looks like the Intel 5300 AGN doesn't send any packets all of a sudden OR that the DIR-615 has become temporarily deaf. But disconnecting/reconnecting in vista make the network work right away indicating the problem is with the Intel 5300.
As an ekstra test, I tried having the Asus EeePC 1000H (also has 802.11n draft) transfer the same files while the HP 8530w was and then the network was MUCH more stable. The HP 8530w experienced 1 dropout but the EeePC continued transferring at full speed. Obviously the Intel 5300 AGN has severe problems talking with the DIR-615, problems so big it cannot figure out how to recover normally. :-(
Needless to say, I have tried playing with most settings in the Intel 5300AGN and also with the DIR-615, but without success. The network breaks down, always.
On the plus side, the EeePC 1000H is stable.
I wonder if it is possible to exchange the Intel 5300 in the 8530w with another wireless lan? I'd prefer to have a card that works.
is it possible? how easy is it to do it yourself?
I have an elitebook8530w 2.5ghz core2duo atm and would like to upgrade it if possible.
way to check out laptops before purchase so i would like to hear opinions on 8530w sxga+ screen(1680x1050)
i work primarily on laptop with no external display and 1920x1200 is way too dense for me. as i have seen in reviews wuxga display is quite good, but i have no idea on wsga+ quality
i use my laptop for design, so i'm interested about viewing angles and color rendition
Via MS windows update there is an update to Nvidia Quadro FX 770m graphics. I installed it, however the screen back light brightness got capped and would not go beyond 2 points (out of 5 points) and hence i had to revert back to original drivers.
View 3 Replies View RelatedIs there some way around this? I ended one of the process one time, I VolCtrl.exe * 32, and it made the onscreen display go away, but then I could no longer adjust the brightness (probably because the onscreen display is identical for both except for a light icon insteam of a volume icon)
With that process not running volume control still worked fine, but screen brightness changing went away, a price I can't afford to pay for that.
ANyone tried scrtching the lid with a wool pad ?
View 8 Replies View RelatedTITLE: HPQFlash for HP Notebook System BIOS (68PSU) - Microsoft Windows-Based
VERSION: F.10
PURPOSE: Routine
SoftPaq NUMBER: sp46785
SUPERSEDES: sp45539
EFFECTIVE DATE: December 08, 2009
CATEGORY: BIOS
SSM SUPPORTED: NO
PRODUCT TYPE(S): Notebooks
HARDWARE PRODUCT MODEL(S): HP EliteBook 2530p Notebook PC
OPERATING SYSTEM(S): FreeDOS
Microsoft Windows 7
Microsoft Windows Vista
Microsoft Windows XP
LANGUAGE(S): Global
FIXES: - Fixes an issue where the computer is unable to boot from some attached USB
devices.............
Windows 7 Ultimate x64
T9400 2.53GHz 6MB L2
Memory 2gb 667mhz
320gb HHD
I wanted to upgrade my ram in my 6930p Right now I have to temp ram 2gb 667mhz. I want to upgrade to a 800mhz but I don't know how much I should get I wanted 8gb but I'm not going to play much hard core games so this might be to much.
What do you consider to be the best overall memory needed for games and App.