I've got a Sony VAIO Z690. I'm trying to connect it to my Westinghouse L2410M monitor - it is a 24" 1920 x 1200. Connection is through HDMI.
I've got it running at native resolution, but the text on Windows and applications look blurry. Colors also look dull.
Strangely, when I played a 1080p movie, the quality seemed ok. But once I closed the movie, the text is still blurry and the colors are dul
I am running 2 external displays through the ultradock on my t440s. The built in display looks nice and crisp. My second monitor is 1440x2560. The task bar is sharp and the title of most windows looks good. All programs looks terrible. Firefox is a blurry mess.
View 1 Replies View RelatedThis is on a HDX16 running Vista Home Premium SP1. The maximum/normal resolution is 1920x1080, but that was alittle small so I changed it to 1360x768. Now all the text (really everything) looks out of focus.
View 5 Replies View RelatedWhen I attach an LG 22" 1920x1080 monitor it eventually starts to slow down. Video won't load properly, the mouse starts jerking, etc. This is the secing F-11 I've had this issue with. I don't see memeory leakage but I have 8 gigs of ram, I loaded drivers carefully, and checked each, but the heck of it is that the laptop works perfectly when I remove the monitor. Could it be the monitor itself? It works with my SR & AW. Both are Vista machines though.
View 8 Replies View RelatedSome texts look blurry on some windows. I have attached a picture to show you what I mean. If you see "Device Manager" window, the text is blurry. On the other "System" window, the text is just fine.
Link to image...
I just bought a used but fully working Vaio VGN-FW11e with a cracked screen (got it for a good price). The lcd-panel had been removed but the lid is intact. The cracked screen didn't bother me since I planned to have it permanently hooked up to my projekter using the VGA-output.
The problem is that it doesn't seem to turn on the VGA-out before Windows has loaded, i.e. it is impossible to see the POST/loading of BIOS. When trying to restore Windows to its factory settings (since the old owner had left all his files and folders all over the place) using the Vaio Recovery Center something went wrong and now I'm left with a dead system.
When turning the computer on I can hear and see what seems like a proper POST, i.e. the hard drive spinning, the dvd drive spinning etc. But a few seconds after start, when it's supposed to start loading Windows it just stay still, most likely with some kind of error message.
I desperately need to be able to activate the VGA out during BIOS to be able to reinstall Windows. According to Sony this is not possible. But it sound almost silly since every other laptop I have had has been able to output a picture to VGA directly during POST. Is there some way since the obvious Fn-F7 doesn't work?
I just submitted an order for a new vaio z and while waiting for it I thought I'd look into getting a nice external monitor for home use. After reading through the forum, I can't find any report of a vaio z owner successfully attaching an external monitor with a resolution of more than 1920 x 1200 (due to no dvi-dl compatibility). Specifically, I was hoping to get a 30" 2560 x 1600 monitor.
Is it safe to conclude that it is impossible to connect a 2560 x 1600 external monitor to my new vaio z?
i just bought a Sony Vaio Z (1600x900 resolution) and noticed that the 1600x900 resolution is way to small for me, cant barley see any text on the screen
so when i change to the next resolution (1280x) all the text and fonts get horribly blurry and "loses" the crisp that it had in the 1600x
I want to buy an external monitor for my sony z590. I was wondering what resolution the graphics card on the laptop can support. I want to maintain the same 16:9 aspect ratio, so i'm looking at monitors with 1600x900 or 2048x1152.
Does anyone have any experience with this? The only reason I'm looking at the 2048x1152 is because I want to have the same clarity and sharpness on the monitor as I do on the laptop screen.
I'm looking to get an external monitor for my z series.
1. Is it best to get an HDMI monitor - what are the advantages over a standard monitor?
2. Will the graphics card be able to power more than my current 1600x900 res?
3. I'm looking for a good 21-24 inch monitor, thinking about Samsung,
4. I'm assuming running dual monitors is out of the question?
I just picked up a Z laptop. Got the docking station the VGP-PRZ1. The dock has a vga and DVI connector. When I connect two monitors to the dock the software will only allow me to turn one on. I get an error "this gpu only supports a single display"
Does that mean I can not use 2 external monitors?
I am trying to use an extra monitor at work (in extended desktop mode, not clone mode) so that I can use by the laptop's display and the extra external display.
The external monitor is 24" with native resolution of 1920x1200. It works great when hooked to my desktop or other machines.
When I hook it to the laptop, it becomes fuzzy and slightly blurry. Not horribly, but enough to hurt your eyes and make you not want to use it. Anyone had this problem? I've tried several different cables to eliminate that as an issue, but like i said - it works fine when hooked to my desktop.
I have 2 identical VAIO laptops. Sorry don't remember the model. If important
I will check when come home. But they are last year model core 2 duo.
Silver ones
One of laptops fall down. The screen is not functionning (just all kind of lines).
It goes to windows prompt( I can see background of login box.
When I connect external screen, there is no output signal.
First, I thought that something is really wrong with the board. FN F7 make no changes.
But I decided to connect external screen to my second identical laptop.
And it not gives any external signal. But when I login to windows I can switch to external with FN F7.
Looks like F7 is managed by software inside the Windows.
Logically output from the laptop should be during the boot.
What are my options? Don't want to put a nice hardware in the garbage.
I recently just purchased and received a fancy Dell e6400 from one of the many dell deals. My eyes are light sensitive from looking at many computer screens over the years and due to this I avoid LCD screens and much prefer flat CRT monitors. My goal is to use the e6400 as my workstation computer while using the VGA out to power my 19in Sony CRT .....
View 6 Replies View Relatedi dissasembled my presario cq60 and when i put it together the monitor won't activate.
i tried using an external monitor and the monitor refused to turn on from standby, a safety feature of the monitor. the small card in the underneath with 2 wires leading 2 the monitor, (i assume that is the laptop version of a graphics card) is fine, inserted properly, and i had a slight issue with the plugs fitting, but that was soon resolved.
What is wrong with my vaio VGN SZ 484N? Everytime I plug it into a monitor, the monitor has a pink screen. All the monitors including my new Bravio 32 inch TV/ monitor cannot have a problem. It must be something to do with the vaio settings for the monitors I plug into?
I have tried all the display setting bits and pieces and nothing helps. If I reset or tick white balance reset on all the monitors contols it is fixed whilst I am holding the button and then reverts to pink screen when I release. Definitely being determined by the VAIO.
My friend has a VGN-FE590 that has problem with the LCD. She thinks its the video card, but I don't think it is, I think it's the LCD itself. The LCD as soon as it turns on turns into a weird grayish color and it looks like someone filled the inside of the LCD with some liquid although she knows nothing about it. I can output to an external monitor perfectly fine, so I don't think it's the video card. I pulled the laptop display apart today thinking it might have been the wires going from the motherboard to the LCD, or from the LCD to the inverter, but it made no difference, the wires all looked fine, and jiggling them around did nothing.
Basically what happens when you turn it on, it loads to the windows login screen, you can barely see anything, and if you move the mouse, you just see it slowly disappear off the screen, and then reappear where you move it, like you can't see the cursor when moving it.
I'll just list the details below, kind of says it all. other than the fact that I am going crazy trying to getthe back light to work under Windows again.
Sony Vaio PCG K23
Raedeon IGP 345M video card
Monitor works up until Windows loads.
Monitor works when running Ubuntu. Repeated 3 times
Monitor works when at C: prompt.
External monitor works when plugged in to port.
If I look hard enough I can see my desk top on the screen so I know it’s there
Have run System Restore 6 times from restore disc that were made on first use.
Have run System Restore 3 times by pressing the F10 key.
BIOS was still at default values, but I reset it anyway
Windows XP Home SP2 and is completely up to date.
All drivers are as current as I could find.
Windows indicates all drivers are working properly.
Refresh rate is at 60HZ.
I know the monitor works as it works fine with Ubuntu. However I cannot run one of the primary applications
I need to use under Ubuntu so I have to have Windows loaded.
I just bought a second-hand Sony Vaio TZ 390, which came with Vista. I updated to Windows 7 and installed all the drivers. Everything seems to work but I cannot get the Vaio TZ to output to the external display. What happens is the external lcd gets a signal initially when I turn on the Vaio TZ (connected to the lcd) but it loses the signal shortly after I log into Windows 7. Btw, the lcd I use is a Samsung 2333HD.
View 10 Replies View RelatedI've got a european Sony Vaio Z (first generation), which seems to have some major overheating issues, especially when it's connected to an external display.
Setup:
Sony Vaio Z11VN -> Docking station -> NEC2690WUXi (running at 1920x1200)
Here's a summary of temperatures when this machine is in SPEED mode (Nvidia 9300gs) in Windows XP (idle)
GPU: 92C(198F)
HD0: 41C(106F)
Temp1: 66C(151F)
Core0: 78C(172F)
Core1: 78C(172F)
Clearly, the temperature drops if I switch to STAMINA mode, or if I unplug the laptop from the docking station, however, in the latter case the temperature drops to perhaps 70C.. so that is without running it on the external 1920x1200 display.
and when running 3d applications or games, the laptop can simply shut itself off for no reason whatsoever (overheated?)
I've heard about overheating problems of the NVIDIA GPUs.. is this such a case? (NVIDIA 9300GS)
I'd like to know if anyone else have had this problem with their Vaio Z (i've seen ppl having problems with the FZ)
My model is a VGN-Z11VN (swedish, although distributed via the UK)
Vaio notebook model number: PCG-VX89
Trying to install OS with external CD/DVD drive to no avail. Have done everything possible including:
-tried 3 different externals drives
-attempted BIOS BOOT ORDER: BOOT FROM CD/DVD and tried REMOVABLE DEVICE setting
-attemped 'esc' one time BOOT ORDER at startup...attempted both CD/DVD and REMOVABLE DEVICE
System doesnt recognize EXTERNAL CD/DVD in BIOS....only in WINDOWS..after machine fully starts up. Looked for any kind of UPDATE for DRIVERS OR BIOS on SONY SUPPORT for this model...there is none.
i bought a sony vaio AW laptop (the newest model, dont know the exact model, its an 18.4 inch etc..,
The bass is very weak, on the speakers and on the external output aswell.
I tried to play with the equalizer, but it didnt help, because probably the output on theese levels is so low, that it doesnt really help to play aorund with it..
I'm on the lookout for external monitors (20-24" WS) that work well with MBPs (13" 2.53 model in particular). I'm leaning away from Apple Cinema Displays (due to their lack of support for non-Apple computers which I own. Pl. correct me if I'm wrong in doing so).
View 10 Replies View RelatedI've hooked my Macbook Pro 15" to an external Dell monitor, keyboard and mouse and everything seems to be working fine - I can put the laptop to 'sleep', then wake it up via the external keyboard and then use the external monitor as the main monitor with the laptop screen 'asleep'.
All working fine, but only when I'm using the power adapter. If I try and run from just the battery the laptop keeps going back to sleep. It 'wakes', but after a couple of seconds goes back to sleep.
Is there any way to use an external monitor with the XPS 13. Â It would make working with photos on the road much easier.
View 3 Replies View RelatedI'm looking to purchase a external monitor for my Studio 15
What the maximum resolutions that my laptop will support? I was told that it will support 1920x1200. I just want to double check that
When I hooked up an external monitor to my E6400 laptop only narrow range of resolutions were available.
The required resolution was not listed.
Do I need to get some drivers to solve this issue?
Right now my internal screen listed as generic pnp monitor.
I have the WXGA+ monitor
I was wondering if anybody else is having issues with using 2 external monitors with their M6400?
My configuration:
I have a M6400 Covet, FX3700M, 8GB, Vista Ultimate 64, A01 BIOS, updated drivers... connected to an E/Port Plus 210W Port replicator. I have a 24" Dell 2405FPW external monitor connected to display #1 (1920x1200) and a 19" 1908WFP connected to display #2. (1440 x 900). Both are connected via DVI connectors.
My problem:
The secondary monitor never has problems... However, the main monitor (24" @ 1920x1200) goes all crazy. It has red "dots" that appear all over the screen in dark areas. The bottom of the screen sometimes has horizontal bars. I see red and black vertical bars as well. The screen constantly flickers and the image hangs off the edges many times. If I change the resolution to BELOW 1440 x 900 the screen looks fine. Anything over 1440 x 900 goes crazy. (none of this occurs when using the LCD on the laptop itself)
The 24" monitor is fine. I have swapped cables and they do not help. If I plug up my desktop computer to the montior- it is perfect in 1920x1200. If I plug up my old Dell Precision M90 using it's old E/Port docking station- it too works fine in 1920 x 1200. So it's not the monitor.
Dell support doesn't know what the problem is. They say it's probably a driver issue. (I have the latest driver) They say they will contact me in the future if there is ever a solution and they are going to escalate it to their video hardware team.
Is there anybody else out there experiencing the same issues as me?
If you are running dual monitors successfully with the E/Port Plus 210W, what monitors are you using, at what resolution and what connector? (DVI or that new display port thing) If you aren't using the E/Port Plus 210W- what docking station did dell sell you?
I need to get a resolution to this ASAP.
I've attached two photos taken from my digital camera showing the screen issues.
I am about to take delivery of an XPS M1330 with the 128MB NVIDIA GeForce 8400M GS graphics card. When at my desk, I am looking to use the laptop with a Dell 19-inch Widescreen LCD Flat Panel Monitor [url] I am hoping to use the external monitor at the same time as the laptop monitor (for example, Outlook on one screen and Internet Explorer on the other).
- Is this possible? Does the graphics card support multiple monitors / dual view in this way?
The XPS screen resolution is 1280x800 and the resolution of the external monitor is 1440x900.
- Will the fact that the screens have different resolutions cause any problems?
I recently purchased an XPS M1330, with:Intel Core 2 Duo Processor T8300 (2.4GHz/800Mhz FSB/3MB cache)Intel Integrated Graphics Media Accelerator X31004 GB DDR2 SDRAM 667MHz (2 DIMMs)Genuine Windows Vista Home Premium
I'll mostly use it for AutoCAD, SketchUp, etc.
I want to purchase a monitor, but I'm not sure about a few details:What's the difference between buying a laptop with an HDMI entry, versus just buying one with a DVI entry (which seem to be cheaper), and get a HDMI-to-DVI cable?What's WXVGA and all those 5-letter-acronyms
