I have 1TB HDD and 60GB SSD installed,and the ISRT driver/software updated to the newest too.
How to enable Intel Smart Response Technology.To use the SSD caching.
There is no RAID or "Intel Smart Response Technology" choice in BIOS->SATA.
I have a laptop Inspiron 14R 7420 with HDD and SSD.
I want to use ISRT but i found there is no "Intel Smart Response Technology" choice in BIOS->SATA.
How can I use ISRT?
Just bought an Inspiron 17R SE 7720 with a 32gb SSD. Started it up today and completed the 'setting up windows' bit. Opened up 'Intel Rapid Storage Technology' and it can see both of my 750gb HDD, and the 32gb SSD but there is no 'accelerate' tab available.
Incidentally, when I click on My Computer, I can also see both 750gb HDD and  32 GB SSD- i though the latter  was not supposed to be visible here.  Under 'Computer management' the SSD has an 8gb 'Hibernation' partition and a second usable partition.
Having read numerous posts about this already, I have checked in the Bios that Intel Smart storage is already selected.
I'm in the process of upgrading my L521X/XPS 15 to Windows 8. The A09 BIOS introduced UEFI booting, which I of course intend to use. However, I can't get Windows installed when Smart Response is activated in the BIOS. The installer simply doesn't show any disks - even when loading the correct drivers. Changing to AHCI allows me to install - but of course without the benefit of Smart Response. Now, the question is: is it possible to use pure UEFI and Intel Smart Response Technology on the L521X?
View 2 Replies View RelatedI have a lenovo u410 with a 500gb hdd and a 24 gb cache. Now, I am experienced with hardware and software and have built/reinstalled a lot of computers before. This time it is a bit different. I did not get my windows 8 key with the computer only the OneKey recovery. I did do a backup with this program when the computer was new and I assume it is on the hdd.
So what I want to do is to replace the hdd with a new 2,5 in ssd and keep my windows 8 licence + all the lenovo goodness ( onekey feature, keyboard shortcuts etc..). What would be the best way of doing this? Can i transfer the backup I did to the new drive?
I want to enable in bios the Virtualization Technology but there is no option for that.
Is there any way to do it?
Any alternative bios?
I'm trying to have simultaneous sound from both the headphone jack as well as the internal speakers. I've enabled the concurrent audio via the Smart Audio panel (Audio Director), tried the blue and red buttons (got successful results), but all of the computer sounds still come from the headphone jack.
W520, i7-2820QM, BIOS 1.42, 1920x1080 FHD, 32 GB RAM, 2000M NVIDIA GPU, Samsung 850 Pro 1TB SSD, Crucial M550 mSata 512GB, WD 2TB USB 3.0, eSata Plextor PX-LB950UE BluRay
W520, i7-2760QM, BIOS 1.42 1920x1080 FHD, 32 GB RAM, 1000M NVIDIA GPU, Crucial M500 480GB mSata SSD, Hitachi 500GB HDD, WD 2TB USB 3.0
My Inspiron 15z was just repaired today (it got a new motherboard due to a different problem that is now fixed). But now, whenever I start up my laptop, I get an error message from Intel Rapid Start Technology Manager that says "Your system does not appear to have Intel Rapid Start Technology enabled." I have never gotten this error message before. It is only now after my motherboard has been replaced. I don't understand what Intel Rapid Start Technology is and if I should have it enabled, and if so how to enable it.
View 1 Replies View Relatedi have lenovo G510.i have enabled the Intel Virtual Technology is enabled from BIOS but when i installled Intel Processor Identification Utility shows Status as NO instead of YES. I have upgrades the BIOS 3.09 latest one so far but still same problem
View 2 Replies View RelatedWhile trying to install Intel Rapid Storage Technology(IRST) Driver on my Lenovo G560 Windows 7 64bit OS it is not able to install and gives me some error regarding hardware not match or etc. error then i came to know that to install AHCI driver i have to change in BIOS Sata controller mode from 'Compatible' to 'AHCI' i tried so and then restart the system but it gives BLUE SCREEN error while windows startup logo and restart again, any solution to use Rapid Storage Technology on G560 and actually this driver was installed when i purchased the new laptop but after certain format and fresh windows installation its no more able to install, how to install it back..........
View 6 Replies View RelatedI have a FW and I read the topic about VT which don't support FW series. When I look intel's page I saw that my processor ,core 2 duo p8700, supports Intel VT. how can I activate?
View 6 Replies View RelatedI have installed Widi from hp.com 3.0.13 ver., but not working, not run the software.
View 3 Replies View Relatedwhen I got my 9400/E1705 I was always sad for not having the AHCI option available in the BIOS.
This was asked for so many times:
- "Notebooks BIOS should support AHCI"
[url]
- "Enable AHCI in Dell Notebook BIOS"
[url]
- "Please give us BIOS support for SATA AHCI mode on Inspirons!"
Please give us BIOS support for SATA AHCI mode on Inspirons!
- "Give us real bios control"
[url]
- "Bios release"
[url]
In the Sony forum, they have found a way to activate these options even if they're not present in the BIOS:
How to Enable Intel VT and AHCI on a Napa/Santa Rosa platform Phoenix BIOS Vaio laptop
...
The only item you'll need is a bootable DOS media. Click one of these links for instruction for creating a bootable floppy disk (with USB floppy drive) or usb stick.USB flash1 or USB flash2 or CDR (add modified table file to image before writing).
Instructions:
1.Download symcmos and copy it to your bootable DOS media. This utility is used to modify your Phoenix BIOS settings. Also, download a DOS text editor and copy it to the media if you feel comfortable editing a file in DOS.
2.Go to the BIOS by pressing F2 during start-up, or when the VAIO logo appears, and reset the settings to factory default. Save and reboot.
3.Go back to the BIOS and enable the boot from external devices option. Save and reboot.
4.Press ESC when the VAIO logo appears to bring up the boot selection menu and select the bootable DOS media. At the prompt, type "symcmos -v2 -lDefault.txt", without quotes, and note that there's no space in between the flag and filename. This will create a literal symbol table from the NVRAM named Default.txt which contains all the current BIOS settings. Reboot by pressing Ctrl+Alt+Del. If that doesn't work, hold the power button until the notebook turns off.
5.Use the DOS text editor (or boot to another OS and use a text editor there) to edit the generated Default.txt file. Change the following lines and save the modified file to something else (e.g. modified.txt):
For Napa SZs - R0112N0
AHCI: (015C) [0000] ---> (015C) [0001]
VT-x: (0354) [0000] ---> (0354) [0001]...
I want to enable Intel VT on my HP Pavillion DV2842SE. I need to do this to run a 64 Bit Guest OS in VMware/Sun Virtual Box. Currently, the Phoenix BIOS (version F2E dated 12-2008) hides this feature. I have tried flashing to older BIOS versions just in case with no luck. My Proc is Intel Core 2 Duo T 5600, Mobo is Wistron 30CD, INtel GM 965 Chipset, 4 GB RAM, running Vista Home Premium 64 Bit. I had previously installed XP Prof 64 Bit on this laptop and got Intel VT turned on(so it is clearly supported), but cannot do it when I returned to factory installed Vista Home Premium 64 Bit (some software was not available for XP like Youcam and Multi-Touch scrolling for trackpad,etc and so I had to (sigh) return to Vista).
View 4 Replies View RelatedPhoenix BIOS Editor (2.2) Open R0122S5.WPH, Enabled Intel VT:“setup table”-->"intel"-->"cpu control sub-menu"-->"merom cpu control sub-menu" -->"Intel Virtualization Technoloy" ,Modify "Disabled" "*" to "Enabled",Enabled AHCI: “setup table”-->"intel"-->"ICH control sub-menu"-->"integrated device "-->"ich sata pata control"-->“AHCI Configuration”,modify "Disabled" "*" to "Enabled",
See Figure 2 below,in these two places will be able to successfully Enable the VT and AHCI functions can be a do?You Moren so successful ?
We have a new (1month old) XPS13, which will not boot up. It was being used to watch a video online, and then when that had finished, the lid was closed. When we came to turn it on again, there is no response.
The laptop is plugged in, with a light on the power pack. Holding the power button down doesn't illicit a response. I have seen some mention online of booting up into diagnostic money keeping the function key down and pressing the power button, but still no response.
There seems to be no way of telling whether there is any charge in the battery, so difficult to tell what is causing the issue.
I have installed XP on my Latitude E6500. Baseline is the ALPS Touchpad sucks, it is unprecise, slow and sometimes hangs. The worst I have ever experienced. I even had it replaced by Dell hoping to receive a newer Hardware revision but just got the same pos again so nothing changed.
What really annoys me is that when I wakeup my PC from Standby or Hibernation the Touchpad does not respond for about 20 of seconds so I have to wait.
Of course I have the latest driver 7.2.101.216 from Dell installed.
I have two identical Dell Inspiron17R 5720's with the same problem with the Quote Key. When pressed once, nothing appears on screen. Press again and both appear. Get the same result if shift key is used for double quotes.
The same results get transferred to an attached USB keyboard, so it must be something wrong internally, either in Bios or Windows 7 (SP1)'s setup of the Standard PS/2 Keyboard.
I have Dell inspiron 15r which was fine till last night . But today when I turned on there is no response . Only power light turns on. No sound of fan or hard disk . No beeps. No change in power LEDs color. I did little research on net and tries to remove static charge but it won't work. Now power light is not turning of untill I remove battery. Â When I holds power button for few secs power light turns off for 1 or 2 seconds and turns on after that.
View 4 Replies View RelatedMy laptop takes ages and ages to open applications, new browser tabs and websites. Quite often websites I visit give me a "session expired" message. Sometimes an application will give me a message saying "program not responding" but if I stay patient and don't close it, after some time the application opens!
I have a Dell Inspiron 3521 Laptop. I get this message from My Dell:
Dell Notification about Antivirus Conflict: You have more than one antivirus software enabled. This can lead to conflicts that may impact performance.
I have bought and installed BitDefender Antivirus ... the conflict must be from Windows Defender. Maybe I should uninstall Windows Defender ... how do I do this?Â
I had just closed it the other night after charging it. Then there was nothing - no boot, no LED with charger, no fan. I checked and the charger is definitely functioning, so I worry that this is a problem with the motherboard.
Since it's an ultrabook, I haven't been able to remove flea power since the battery is embedded into the laptop.I wonder if it would be possible for a technician to come have a look at it ASAP?
All of a sudden the SD Card Reader on E5430 laptop doesn't work  When I insert SD card nothing happens. Before, a window would pop up, or I could see the SD card in my computer.
No nothing happens and it doesn't show up under my computer.
Also, under device manager -> storage controllers, not there any more.
I believe it's a O2 Micro OZ600xxx card reader.  I tried installing driver, but still doesn't see SD Card when inserted.
If the SD Card reader is just dead? Or do I have a driver issue. Windows 7 Professional 64bit
is it possible in the XPS M1530,
View 10 Replies View RelatedI did some search on this topic and couldn't come up with similar issue.
I left my SZ on the desk to download few items, when I go back to response a IM, I burn my finger tip when I touch the track pad!!!
The window OS function as normal. However, keyboard and mouse no longer response and there is excess heat coming from the track pad
The touchpad of my Lenovo G50 (i3-4010U) is not working properly (windows 8.1). Sometimes when I use the touchpad, the arrow don’t move. Until it close and open the display, it’s don’t move. In addition, this method does not always work. I have gone to options and I've turned off touchpad options "two fingers" mode, but nothing change. I have still in function an old notebook pc (from 2007, not Lenovo!), and has never had this kind of problem. I need my computer for travel work but this problem becomes very difficult my job.
View 9 Replies View RelatedI need to disable the optimus technology on my dell inspiron 14R 5420, but can't find a way to do it in bios. My bios version is A15. Can I upgrade to another bios with more options?
View 2 Replies View RelatedI just purchased a Dell Inspiron N5050 laptop computer specifically because I wanted a computer that would support WiDi (IntelWireless Display) to my HDTV. I had been under the assumption that all current generation laptops included Intel Wireless Display technology.Â
After receiving the computer, I have just discovered that the wireless network card in this machine apparently does NOT support wireless display technology. Is there a way that I can replace the network card in this machine with one that DOES support wireless display technology or at least addan additional card to the machine that supports wireless display?
Where do I get a contactless or contact dell smart card for my e6400? I can't to find them anywhere
View 6 Replies View RelatedOk so the Studio 1737 premium display is the RGB LED display. Using LED's.
For example even high end HDTV's the most expensive $4,000 Samsung using LED back lighting lists a 2ms response time.
I have never seen such specs mentioned for the 1737's RGB LED display.
I know it has to be fast, because on my 22" Samsung LCD which is back lit using conventional CCFL has a 2ms response time.
and when I connect my 1737 to my 22 LCD via HDMI, I can tell that the response time, on the 1737 is faster, my guess is because of the LED's can adjust or turn on off faster than CCFL.
i uninstalled acer empowering technology with the intention of reinstalling it afterwards. it had been laggy and closed spontaneously for a while, so i was going to download it again from acer support.
i got rid of all the components, went to the website, and downloaded it.
after installation completed it said something about WMIAcercheck.exe not working.
i tried to boot it up, and it said exception message:
and then it said sorry! not an acer system.
however, my computer is clearly an acer system.
it's an acer aspire 5100.
i neeeed acer empowering tech to hook up to the internet, it's extremely slow to do it another way.
