I recently received my Dell Latitude 10 Tablet. I have created a USB install of Windows 8 Pro. The tablet cannot boot to USB. I have tried multiple USB drives and have verified the drives will boot on my Latitude laptop. I have verified USB boot is enabled in the BIOS. When pressing f12 for boot options USB is not an option. When entering the BIOS setup it is not listed as a boot device either. Clicking add boot device does not show it either. I've tried using the USB port on the table and the USB ports on the productivity dock. I have also tried creating the install on a SD card, that does not show as an available boot device either. The bios has been upgraded to A03 and I'm running version 9.14.3.1099, A04 of the clovertrail chipset.
I recently had to realize that the touchpad is not recognized when booting in tablet mode.
As I noticed the keyboard and touchpad are disabled when the screen is turned around or just tilted out of the latching, is there a way to enable them again - perhaps a BIOS setting or update?
I think it would be in advantage if keyboard and pad stay active when the screen is rotated e.g. if there is not much space to tilt the lid, then the screen-unit could be tilted in the frame for a better viewing angle.
I noticed that if i boot my TPY in tablet mode, the cursor simply doesn't show up even if i flip back to the laptop mode. i can only solve it by restarting and booting back from laptop mode.
If i boot from laptop mode however and flip to tablet mode, the cursor reappears when i flip it back to laptop mode.
Updated Bios to A12 today, the system stated the updated was successful but after it's auto reboot it longer boots.
When you turn the system on the screen stays powered off (nothing on the screen, and no back light). The HD and WiFi lights stay on, the battery light flashes.
I've tried removing the battery and powering with just the mains adapter, I get the same problem.
I am booting a Dell Latitude E5420 running Windows 7 and after the POST it just shows a blinking cursor..... BUT WAIT... not ALL the time... it does manage to boot into the windows after I choose the HDD from F12 options or sometimes even when I keep on shutting down and starting up again and sometimes when I do a restore checkpoint in the repair options....
The Diagnostic tests are not working when I go through the F12 and just hangs up showing the message -
Examining ACPI interface Running MATS test
I can't understand... if it was consistently NOT booting or showing a consistent error... but here the behavior is erratic (except for the MATS test failure....
I am stuck with a dell E5440 here power light comes on and then laptop switches off and back on again and just repeat itself! I did not tried anything yet. It is i5 vpro and I installed 1TB HDD few months ago, it has been working no problem since yesterday.
tried to upgrade my Latitude E5510 from 2x2Gb (factury Samsung) to 2x4Gb Corsair CMSO8GX3M2A1333C9. BIOS updated to Rev. A13, latest. Memory is recognized as 8Gb. But booting into Windows7 X64 doesn't work anymore. If I boot from a Lubuntu CD (x86) it runs, naturally only with approx. 4Gb since this is a x86 OS-version. Windows 7 X64 just reboots. If I use Save Mode a reboot occurs when the loading of "ClassPnP.sys" starts. When I put in the old 2x2Gb everything works perfectly. Can't even get into Windows Setup from a clean DVD.
I want to get a x200 tablet (7453-AH3) just for programming classes, but wonder whether x200 will run VS2013 with win8.1 well, such as response speed, smooth or not, a lot lags or not, etc.. Also, will OneNote work well on it?
If I put a SSD in, will that make it better? If not, is that possible to upgrade X200 tablet motherboard & CPU to make it better?
When I put my X220T in tablet mode, the screen moves just enough to move the pointing stick in the middle of the keyboard to cause the cursor to move. I can't rest my hand on the screen without causing the cursor to move all the way accross the screen.
Am I missing a driver that would disable the nub when the screen is turned over it, or is this a design oversight? I've got the latest BIOS.
Does anyone know why on my XT tablet my sleep mode is greyed out?
I tried everything... reinstalled nearly all the drivers... and some power management settings, yet the damn thing is still greyed out. I can't figure it out for the life of me.
When I fold the screen back and use the laptop in "tablet mode", the keyboard automatically get disabled but the touchpad does not. I have tried looking in the mouse and touchpad settings to no avail and it is very frustrating!
I had bought a lap with 500 GB hard drive 2 days back. now its not booting properly showing a window
" Window failed to start a recent hardware or software chage might be the cause Select from below
1. launch startup repair 2. Start Normaly "
in the first case i cannot restore the the factory settings nor the system restore and when i selsect normaly a blue screen blinks and the system get restarted again
When i tried to setup using windows vista Disk its showing both drives but the main c drive (450 GB ) is shown as unallocated disk and when i created a following text popeup showing " Failed to create new partition on selected unused space " and only second drive 15 gb is shown active and its is a bakup drive of Dell
I've recently bought myself a new HP tc4200 Tablet PC which doesn't come with an operating system. I'd like to install Windows XP Tablet PC Edition on it but unfortunately the tablet didn't come with any discs. I have a working Windows XP Pro Volume License disc and serial number but I've read that you need a specific Tablet PC disc which you have to purchase as an OEM version. I've heard that you can change the PID in the setupp.ini to make the Windows setup think it's a Tablet PC disc but accept a VLK -has anyone done this and confirmed that it works?
Trying to update USB3 driver via various options following re-install of OS (another story/issue) - tried via the drivers CD but couldn't see what I was looking for. Back to Dell website and downloaded and 'installed' what was hopefully the right one. Re-booted, but aagh forgot to take the CD out of the drive! And the laptop entered lots of stuff via the command prompt screen and has come to a halt with a message:
A RAM DISK drive is available for this boot cycle as C.It contains several Hard Drive setup tools. Please use these tools only under the direction of Dell Support Staff. I understand the bit about Dell Support Staff, but hoped I could just exit in the normal way (exit>enter). Having said that, I don't know many command prompt entries... It's the full screen, not a command prompt window.Dell XPS 17 win7 x64.
Recently I wanted to buy an HP tablet pc since it seemed to me to be the cheapest available to try and see if a tablet pc could help me out in what I'm going to do: an animated thesis that will require a lot of painting.
So I did a bit of research and found out that the newest model they carry doesn't support a lot of professional programs (ex.photoshop) only to add a multi-touch experience. Unfortunately I think this is a very poor choice from HP so I set to find a previous model that had the digitizer that I seek.
It seems to me the previous model with wacom technology is the HP pavilion TX2600, which in turns has a LOT of flavours: 2622, 2635, 2640... etc up to 2650 (it seems). Each of this versions has another subversion like: US, EW, EG, etc...
What is going on? The specks of some of this models are basically the same, but what is the difference? Which one is the latest one that I should try to find?
I just intalled a new disk that is running quite well, except that I cannot run xpmode. I get the warning that I need to alter the bios, but not setting exists on the chip to alter it for virtualization. Why could it run before on the same chip, but no longer. Is there a workaround. Is there a way to copy the settings from the old hard drive? I suspect not, but I am sometimes an optimist.
My Inspiron 13 7000 2-in-1 laptop, after having the screen and hinges replaced due to other problems (ghost touches), now won't auto rotate the screen when in tablet mode. The keyboard is also functional when the screen is pushed back past 90 degrees, so when the keyboard is on my laptop but the screen is facing me. This doesn't happen in true tablet mode however.I've tried reinstalling all of the up-to-date drivers; chipset, BIOS, along with the ST Microelectronics 3-Axis Digital Accelerometer Driver.
There are a number of issues I can highlight that stop this from working;
1) in device manager there is no entry for ST Microelectronics 3-Axis Digital Accelerometer Driver, nor Accelerometer or anything I presume makes this function work. There is a Sensors collection, but nothing in there I think is it,. There is also no 'Unknown' device listed.
2) I should see PopUp_DM.exe in the running services and in the startup selection of programs. This is nowhere to be seen.
3) I don't appear to have a "Sensors" applet
4) when I choose 'Normal Startup' in msconfig & then reboot, it goes back to the bottom option, Selective startup. Is this something I need to do via the Dell BIOS Advanced Options?
Other than doing a full restore, which I loathe to do again as already prompted by Dell previous to this issue, what can I do? A bit worried that when Dell replaced my screen they didn't refit or include the accelerometer!
The price of 2nd user Latitude D630's seems to be holding up quite well in the UK. Does this indicate that it is still a popular machine and favoured over the E6400?
I briefly checked out an E6400 the other day and for a choice between machines of approximately similar spec I would opt for the D630 rather than the newer E6400.
I would be interested in opinions from users who have experience with both models.
We are looking at getting some Latitude E4310 systems. Since fast boot up to access the web is important, we see that the Latitude On FLASH option is required.
The downside is that Dell will not install this along with the WiMax card option. They have a combo WiFi and WiMax card, but it can not be installed with the FLASH option.
They also list Latitude On ECM as an option instead of On FLASH. The ECM runs $149 more. With ECM, the system can then have the WiMax card which would be nice.
The people at Dell have not been able to provide a good explanation on what the ECM option does. There is a write up on the FLASH option, but not a good one on ECM. Does anyone know what the ECM does differently than the FLASH?
Key points of the FLASH option are (we need these functions): Boot Fast, 8-10 seconds Wi-Fi and LAN 10/100/1000 Web access via browser Firefox Browser Supports Java and Adobe Flash Read Microsoft Office Edit Microsoft Office 2000
Which do you reckon i ought to go for between the two?
The laptop will be used primarily between home and university, so will be taken between the two places in my shoulder messenger bag, so will probably take a few bumps
i got this HP tx2-1020us Tablet PC AMD Turion. 2 weeks ago suddenly it got this problem:
when turning on the power button, i see LEDs on keyboard and around (but not the HHD led), no activities at all. the LCD is totally black/blank. nothing ever appeared on the LCD. so, is the tablet dead?
My function key is always on so that I have to press it when I want it to be off. An example of this would be that I have to hit Fn+Alt+F4 if I want to close a window. I believe this has to do with me downloading a BIOS update for Windows 8 but I cannot find how to disable it.
I have created the special 8gb partition. I have installed RapidStart drivers app and enabled RapidStart. At first it works - i put helix to sleep, and i can see after some time that the led stops flashing so the tablet goes to hibernation. However, after lying some time it wakes up again, and stays in sleep mode, and not hibernated mode, and thus, eventually runs out of battery.
I am having a problem with a ThinkPad Helix and was looking for some advice on the troubleshooting process. The tablet was dropped and it suffered some damage. When I received the tablet I noticed that it still powered on but there was no video. Upon closer inspection, I noticed that the monitor is still displaying video but it is very dim. When I shine a flashlight to the monitor I can see the windows logon screen and the touch panel recognizes me tapping the screen.
The first thing that I tried was replacing the cables that connect the monitor to the motherboard as some of them looked like they had forcefully been removed. This had no effect on the issue as the monitor was still very dim when I powered it on.
I thought that the monitor was the problem and decided to replace the entire screen assembly. I was able to get another monitor that matched the part number of mine and swapped it with the old one. When I turned it on after swapping the monitor I stil the had a very dim screen. If it wasn't the monitor or the cables that connect the monitor to the motherboard then the only thing that was left was the motherboard.
Again, I found a replacement motherboard for the unit and swapped it. When I powered it on I still had the same issue as before, very dim video. It doesn't look like the thinkpad helix has an lcd inverter or I would have tried replacing that first.
