I just received my new M4400 and like it. However, the 9 cell battery I have seems to fit a bit loose on the left side of the computer.
While not a huge issue, it is annoying. Does anyone else have this issue? Should I send the battery back or could it be the internal latch that is loose?
I was just wondering if any of you have the same problem. My 9 cell battery is loose from the battery slot on the dell e6400. Is it normal, or should i send it in for a repair
View 10 Replies View RelatedI know there currently is a 6-cell and a 9-cell for the M4400.
However I also remember reading that Dell has a 12-cell out for some notebooks in the new E-series.
Does anyone know whether there is going to be a 12-cell battery that can be used with the M4400?
I was running some tests today see how many watts was being pulled from the batter while at full load on my M4400 laptop after installing RM Utility. But found something I never noticed or did not happen before.
When set to max performance 100% CPU speed all the time, the systems keep the processor at 100%. As soon as you apply load while on battery it shoots down to 39% of full processor speed and then hops up and down. You can even see it in the temps while running tests, the processor is definitely not running at full speed. I swear I remember doing this same test a little while ago with no problems but I could be wrong.
So can I not run the systems at full capacity while battery power??
I was on A15 trying this test and downgraded to a14 with some results
Works fine and dandy while on AC
My M4400 6-Cell battery goes for about 45min on full charge. Ive had my laptop for a year now. Is this normal that it dies so quickly?...
I started noticing this a week or two ago and now on startup I even get a notification saying "your battery life is decreasing, now is a good time to buy a replacement battery"...
I dont remember how long my Inspiron 8200 laptops battery lasted but it feels like this one gave in really quickly. I do use my laptop a lot. Its on most of the day....
I have a Dell Studio 15 laptop and one of the USB ports on the right side of my laptop has become loose (I think it happened when I knocked it on something). Whenever I put a USB into the port I can wriggle it side to side & I can't do this with my other ports & until recently I couldn't do it with this one either.
When I put a USB into the port it isn't detected but if I push down on the casing above the port it sometimes is detected but the second I stop pushing down it's undetected again.
My 640M is still working fine but the LCD hinges seem to be a little loose. i.e. if I tilt the laptop a little, the lcd seems to bend on either side I bend it upon.
I noticed that my friends' laptops - Dell inspirons but newer models ( 14, 1420) etc do not have this loose LCD hinges.
I dont remember if the hinges were loose when a new laptop arrived, but its been about 3 years now and I notice this
I have had my M1530 for abut half a year. At the very beginning I noticed that the screen is not very stiff, for example I the screen lid can be moved by about 2 cm almost with no effort (with one finger) also the he hinges (the bar inside) moves up few millimeters when closing the lid.
It's noticeable when looking at the hinge, and also I can feel that from the force used to move the screen for first 2 cm. The problem des not seem to increase and for the first time I thought its normal, but some time ago I saw an identical XPS without that problem.
I have an XPS M1530, 18 months old, and I am very happy with it.
Over the past few weeks I have noticed a problem with the display, any white parts of the screen image show as red or turquoise colour heavily lined, or black text may have a red halo.
I can easily correct this by changing the angle of tilt of the screen....
If I were to reinstalling my operating system, will I loose all my data, personal documents and pictures?
View 1 Replies View RelatedI recently did..well something to cause the headphone jack on my SR to just go limp and useless *that's what she said*....is it possible to fix this if I disassemble the thing? solder job to get it reconnected, or is it as good as gone?
View 4 Replies View RelatedI just bought a brand spankin new HP dv5t series, got it 3 days ago, i inspected it when i got it out of the box and it was beautiful.
However a little later I noticed that the power (cord side) that you plug in to charge was pretty loose.
Now just today I tripped on the long part of the cord... it moved the laptops position on the desk a few inches, and enough to pull it out of the box in the middle of the cord, and it feels even loser.. but I cant tell if it really did, i might just be paranoid.
This worries me because on my last two laptops they were pretty tight and had no play in them, both of the ended up broken.
If you have an Phoenix BIOS (there should be a small logo at the right lower corner..)
And with a broken/desoldered/loose GPU (black screen with blue bars)
Can you press Help Win+B (or ctrl-b, alt-b) then turn on the laptop. Does it make beeps?, if you put in a USB floppy disk, with a disk inside, does it try to read it?
If so it might be possible to rewrite the BIOS so that it will initialize the "Vidock/hwtools.net" pci-express adapter FIRST.
Just like how in BIOS you can "set it" (via setup) to initialize the AGP or PCI video card FIRST, or PCI-E or PCI video card FIRST.
I often use my laptop on AC and remove my 9 cell battery. The only problem is that removing the battery leaves the motherboard somewhat exposed to the elements.
Is there anywhere I can buy a plastic "dummy" battery to fill up the space?
My Vaio is just out of warranty and it's always had a bit of a clicky odd left-button.
I've noticed that it is gradually getting worse so I'm expecting it to break soon. I should have had it done while the computer was in warranty, but I've heard bad things about their service centre, and they'd probably have charged me for the repair anyway. I did ask them about it toward the end of the warranty period and they wanted me to email them Admin passwords and then pick up the computer for an undisclosed period. I just didn't fancy it - my fault.
Anyway, I have several friends at work who are IT technicians and one of them will have a look. I haven;t found a service manual for the CR series yet, but I'm assuming the buttons are part of the mount for the trackpad and can either be replaced individually or the mount (or pad) can be replaced.
It's just over a year old and I'm thinking about boosting the RAM, HD and upgrading to W7, but on the other hand, I'm not convinced the machine is going to survive another 2-3 years...
I have a HP9743CL sitting next to my old 2529Cl and both connect to my home wireless network. Two weeks ago the 9743CL worked fine but now it drops the connection after 4 minutes. I turned off the firewall on the laptop thinking maybe it was blocking something. That didn't help.
I turned off the firewall on the router Westell327W and that didn't help. in the mean time my 2529Cl just keeps plugging along. staying connected. Is there a setting I accidentally changed.
When it dies and I try to have internet explorer fix the problem if comes back with a statement saying my firewall is blocking port 80. Well, now that everything is turned off what is the cause.
I was running zonealarm on the 9743CL and the stock firewall on the Westell327W.
My laptop is HP 15-r077TX. My mousepad is very loose and making an annoying sound when I touch it with little pressure . It is a hardware failure >My notebook is under warranty
View 1 Replies View RelatedI have a Vostro 1500, which I bought 10 months ago. About 3 months ago the screen became loose and wobbled about 10 degrees when computer was moved or if I was on the train and it went over bumps. I tightened the screws as advised but this did not have any real effect. Dell engineer came and replaced the back cover with new hinges, (as they though hinges may be broken/at fault but they were fine,) but some wobble was still noticable so he ordered a new base. He came today and took the screen out complete with all the screen casing out of the old base, and put it into the new base, but still wobbled, so just put it back in the old base as it wouldn't have cured the problem.
Now yesterday, after he put the new back cover on, he had to take the plastic around the front of the screen off. After he put it together I noticed that the screen is no longer flush with the plastic surround and it annoys me! Am I just being finicky/picky or should I ask them to fix it?
First take the battery out and remove the bottom part like so.
Then you have to take the fan off there are 3 screws to take out and unplug the fan connector.
After you take out the CPU heat sink "there is 4 screws".
Then the Video card heat sink 3 screws.
Once that is done I took the CPU out you don't have to take it out I just wanted to see it. You do have to take out all the extra thermal past from DELL from the CPU and GPU and the 2 heat sink like so.
I use a plastic card and paper towel to remove the extra paste and it workes grate.
Now for the AS5 put on each of the components you just clean as in the CPU and GPU and the 2 heat sink like so.
same go's for the CPU and GPU then jsut use a falt plastic card I just use a master card but any thing similer will do to even out the SA5 like don't try to get it all nice and flat just make sure it covers all the surface of contact of the CPU GPU and heatsink and you should be good, it soule look like that now.
Now just re insert the GPU heat sink and tight the 3 screws back.
After it's the CPU heatsink and it's 4 screws like so.
Now the fan 3 screws and one connoctor.
Close it all up and boot Hope it helps some of you.
Mine was 55 and idle and now 49/50.
Considering that this is a "heavy duty" notebook, how much would a 25W processor (e.g., P9600) increase battery life and decrease heat? In my experience, the difference has been very little for relatively similar notebooks.
View 7 Replies View RelatedI am considering buying a Precision M4400 but I've read about various audio problems, even with the audio outputs .....
View 6 Replies View RelatedI'm currently trying to decide between the M4400 and the HP 8530W. Please could any M4400 owners let me know their thoughts (happy or otherwise)?
The basic specs are as follows:
Dell: P8600 CPU, 4GB RAM, 160GB 7200rpm HDD, Quadro 770M, 1920x1200 display, 6-cell battery.
HP: T9400 CPU, 2GB RAM, 160GB 7200rpm HDD, Quadro 770M, 1680x1050, 8-cell battery.
They're about the same price where I live, and both have a similar lead time. I've had no major problems with Dell in the past, but the M4400 seems to have been slated here and elsewhere for its build quality and design issues. The HP is by no means immune, but it does seem to come off lighter .....
When I got my M4400 last week, it had Vista Business installed - wasn't bad and unlike most people, I've NEVER had issues with Vista Anyway being a Microsoft Gold customer, I got my hands on the Windows 7 Ultimate RTM version and installed this on the laptop.
It has transformed the laptop just like it did my PCMUCH quicker, the graphics seem a lot happier in W7 too.
I've installed all my other tools such as SQL2008, Office 07, Virtual PC with VMs, VS 2008 etc etc but it doesnt even flinch under pressure.
If you are happy with M4400 and Vista, you will be even happier with W7 - small mini review but I thought I should give you my quick thoughts on it.
what kind of battery life you're getting from your M4400, with specifics...
list down your spec, which battery you have, and what programs you were running..
I'm getting about 15-20MB/s (transfer speed) transfering files from my Lacie d2 Quadra(eSATA 3 Gbits port) to my M4400 with Vista 32Bit thought eSATA port.
eSATA port has 3 Gbit/s bandwidth, so I wouldn't get about 300-375 MB/s transfering data?
I'm looking to replace a 3-year old IBM X60s that recently failed.
I'm considering a refurbished M4400 from Dell Outlet, and I have a couple of questions:
1.) How is Dell Outlet service and what quality can I expect from them? I know from Lenovo Outlet, most of the refurbished items are actually in immaculate condition. Is that the case for Dell Outlet? Is customer service and shipping times good?
2.) When browsing through the available M4400s, I see listings for both 15.4" WXGA and 15.4" WXGA LED. Are there M4400s with CCFL backlit WXGA panels? When configuring a new one, the only option for WXGA is LED.
And any other comments, advice, warnings, etc,
Can I use a 95W Power Supply for my M4400 along with the 130W Supply I would leave at home?.
Its new and nice as #&$*#(### for guys like me who spend an hour to an hour and a half on the metro then a 2-6 block walk into the offfice?.
This is small @
Dimension 75 x 17 x 145 mm ; 2.9 x 0.7 x 5.7 inches....
I noticed that dell list two compatible models, YP311 and XX243. On Dells website they both have identical descriptions. I assume Dell is just switching between two different manufactures.
Does anyone have any advice if one functions better then the other?
I ordered my m4400 with the "Dell Wireless 370 Bluetooth 2.1 Minicard for Latitude E/Mobile Precision" option.
It has the little Bluetooth light above the keyboard... although I have no idea if that actually means it was shipped with the bluetooth I ordered.
For the life of me, I can't figure out how to enable bluetooth. I can't find the adapter in Device Manager, and I don't see any keyboard combos to enable it.
I need to know the specs of the RAM in my M4400 and was hoping someone here could help me out?
I know it has 4GB Ram, but how many actual Ram slots does it have and what speeds/specs Ram can be put in it? Basically,
i want to upgrade from 4GB to 8GB to give my VM's better performance without slowing down my base OS (Windows 7 Ultimate x64). I don't know which Ram to choose on newegg.