What kind of thermal pad is on the m1530's northbridge?
I found a few, but it is important to note that these pads are very thin, and the one on the m1530is very thick (I think about 2mm)
Here's ebay:
http://computers.shop.ebay.com/i.htm...&_osacat=46322
i have a question for everyone who has removed the heatspreader from an acer 6920g. Did the northbridge made contact with the heatspreader by a thermal pad or by a thermal paste ? mine had something that looked like a thermal pad but when i tried to remove it , it tore into small pieces ( i know a thermal pad is not like that ). i used a thermal paste when i put everything back together. Should i open it up again and use a thermal pad for the northbridge ?. In everst in the sensor menu it shows 42 degrees celsius for the motherboard sensor ( i assume that is the northbridge).
View 10 Replies View RelatedI just had the motherboard/video card on my m1530 replaced by the dell guy because of the old defective graphics card issue. I watched him do the whole thing, and when he re-attached cooling mechanism to the motherboard, he used new thermal paste for the cpu, but not the video card.
I asked him about this, and he said that the surface of the gpu is different and doesn't need it. I don't really believe this, since it looks just like the desktop gpus that I always use thermal paste on. I'm getting pretty high temps now (65-70C idle).
Well i finally decided that i should give this a try after seeing my temps creep up by about 1 degreeC per week. I just ordered some Arctic Silver 5. Ive looked at all the thermal paste topics here and still have a few questions. Firstly, what exactly is the thermal pad and do i have to worry about it? I saw that some people had to remove the pad but when i read through
http://www.robertbromfield.com/Tutor...he%20M1530.pdf tutorial i didnt see anything about taking off or replacing a thermal pad.
Secondly, when applying the thermal paste, do i want to cover the whole "black square" of the cpu/gpu with a thin layer?
And lastly, i heard that this may void your warranty. I was wondering, if i did break my lappy somehow, couldnt i just clean it off so that when the tech guy comes i just claim that i never even opened it up?
I'm planning on changing the thermal compound on my M1530's CPU and GPU as my temps are getting pretty high when playing Medieval 2: Total War. I am getting high 80 degrees on both CPU and GPU.
The thing is I have never changed thermal compund before and I obviously want to get it right!
I have tried to find a tutorial, but I can't. Well I did find this but the link is dead.
I have heard about the 'grain of rice' and 'credit card' methods, but they are a bit vague
hey happy new year to y'all heres the thing so since dell replaced my mobo recently i kept getting high temps and they sent new heatsink with thermal pads and that kept my temps down, but as before the problem may come again so i got Arctic silver 5 thermal grease,
im gonna stick now to the dells pads until i notice higher temps, so what do you suggest, switch to Artic silver? i understand thermal grease dries up, what about the thermal pads? they deteriorate? snce when
i got my system i wasnt getting high temps but over two months it started going up and up and without thermal pad or grease gpu will hit 100 c... so what do you suggest in this case
So ive been dabbling with the thermal paste on my m1530 for a few months now but havent really stressed the gpu to know for sure. Today however, while playing l4d, my gpu temp got up to 88 degrees C and my cpu was in the high 70s.
I havent seen these kinds of temps since i got my mobo/heatsink replaced a year ago. I have opened up my laptop and my fan looks a little dusty but i am not sure if that would warrant a 88 degree gpu temp.
I am wondering if this could be because i applied the paste incorrectly? I am quite sure i did it right and i followed the instructions that were posted on here for m1530s exactly.
I have come to grips with the fact that my E6400 (see specs below) has idle temps of around 42 for both CPUs and around 62 for the GPU (while docked).
While these are not dangerous, and while the slow fan speed is very quiet and therefore doesn't bother me, I refuse to accept defeat so easily.
So, I am thinking of replacing the thermal paste and possibly the thermal pad on my E6400. There is at least one person here at the Latitude/Precision sub-forum who did that, with amazing results
I'm buying either a FX2500m or 7900GTX so I'll need the heatsink to complete the mod of course.
Is there anyway to tell if I already have the heatsink without dismantling my laptop and peeking inside? (I know if I have a dual-pipe card I'd of course have it, just wondering if there was a way to assume). I have a 7800GS in this thing so I'm not 100% sure if it's a single pipe with no heatsink or a dual pipe with a heatsink.
So I just wanted some opinions on if it was safe to assume that I need the heatsink. (I would rather only dismantle the laptop once, when I'm putting the heatsink and card into it, figured some people who have opened them up a few times would know if I'm more likely to have a single pipe or dual).
If you were to put a GPU into the SXPS 13, what would you like it to be? Its default 9400 M is decent enough to trample Intel's IGPs but it could always be better. I mean a 9600 GT on a 13"? It's been done on the LG P series. So what would it be?
View 10 Replies View RelatedI was sent an M1730 but with no bluetooth adapter. There's a little plug underneath the battery in the battery compartment where it would normal sit.
Anyone have any ideas on the best, compatible module to get? I'd like to be able to use a wireless mouse.
It says it comes with
8X Slot Load Super Multi (DL DVD+/-R Drive + RAM support)
I have an LED screen-- in device manager, it says "generic PNP". Any other way to figure this out?
View 15 Replies View RelatedI have Dell E6400 with nVidia NVS160M.
This is how E6400 base looks like:
http://support.dell.com/support/edoc...l/r-h-atga.jpg
Title says all...I am not a hardcore gamer,just want to "relax" sometimes...so,can you post couple of FPS numbers for different games?
View 10 Replies View Relatedwith a 9cell vs 6cell battery?
View 10 Replies View RelatedDoes yours have a plastic kind of film on the hinges? Can I peel this off? Why is it there?
View 3 Replies View RelatedWhat kind of protection kit you use for vaio z?
Such as lcd protector, keyboard protector, sticker , cleaner, wipe cloth etc.
The LCD on my 700m quit working after I dropped it. But OK on external monitor. Got new screen on eBay. Part # slightly different but that's moot now.
After hooking up the two cables to new screen and putting battery back in, I pressed START button. The light would come on for a few seconds and then blink off, accompanied by a faint click. The data cable to screen got very hot in just a few attempts to start up.
Now nothing works (no more blinks and clicks) with either LCD, on either battery or mains. At this point I would be happy just with external monitor. Had I tripped an thermal overload device, and is there a reset button?
I'm working on my friend's old 9300(It still has the factory Dell image installed)
This thing has been on probably 75% of it's life. I want to pull is apart, remove the dell thermal compound, and replace it with ICD7 thermal compound,
but I am afraid that after so long the dell stuff will have hardened to the point of breaking things as I try to remove the heatsinks.
what i wanted wass to fix/bypass the sensor without having to replace the damn board. i couldn't even find a single post staing where exactly the sensor is on the board.
my problem specifically was that beer got spilled on the keyboard. after a while the machine shorted and shut off. I have a Dell Inspiron 9300, with a 1.73 ghz Sonoma CPU. i left the laptop off for two days so some of the liquid would dry out. after some problems and a dozen reboots i got into the bios, then finally through to windows. everything was fine except that the CPU was working at a very low frequency. also the fans were continually at highest speed. the CPU was being reported between 101 mhz to 503 mhz, depending on the software. it was being recognized correctly but showing to operate at 202 mhz in the system properties panel. what was really striking is that the notebook harware software i had installed was reporting the CPU temperature as 85 C. I tried various software to manipulate the CPU frequency to no avail. The temp was a constant 85 C, although i could tell that it was not even close to this temperature since i my laptop was partly disassembled and i could feel the surface of the heatsink with my hand; it was cool.
I finally surmised that the problem was with the thermal sensor on the motherboard. it had probably shorted or got soaked and was reporting the highest temperature it could as a safety measure, thereby limiting the CPU to a very low frequency and not allowing it to throttle above 503 mhz.
My last option, save for replacing the motherboard, was to find the sensor chip, clean it, dry it and hope that it would work again.
But this is not what solved the problem. somewhere on the net i came accross a code, that when entered on an Inspiron 9100 (an older laptop, with a different chipset) would bring up the Thermal Management screen or something like that, which is certainly not accessible via the BIOS. I was playing around with the settings on a program called Hardware sensors monitor, again to no avail, when i finally decided to enter this code:
FN key + zxcvasdqwer. almost the second i pressed z, or maybe after x, the high speed fans shut off! after a short while they kicked back into operation but at a low speed, just like they were supposed to. the program hmonitor began reporting a more realistic CPU temp. i tried to play a high-def movie file and finally it played normal, without any lag or stuttering! as i played it, the fans kicked into higher mode, and the temp which had been steadily rising, began to drop. the program, and most other programs were still reporting the cpu at 202 mhz, windows system properties as well. but since it was playing a 720p video file normally, it had to be much higher than that. i did a reboot and voila!
all monitoring software are now reporting the CPU at 1.73 ghz. the system temperatures are perfectly normal, and at idle the CPU goes as low as 20 degrees C. The software Speedfan, however, is still giving an error regarding the sensor chip on the motherboard.
I seemed to have fixed the severe thermal sensor problem by a few keystrokes, without having to replace the motherboard or even the sensorchip. in fact, i didn't even have to find the sensor node and clean it.
I came accross more than a dozen people who had a very similar problem to mine, with the temperature being reported at 85-86 C, for no reason. At least those who have a Dell notebok might be able to solve this problem.
I bought THIS from dealextreme.
I want to use it when Im gonna be replacing the heatsink
Can anyone tell me the specs for the chipset thermal pad thickness on the e1705 / 9400 / M1710???
I have several that have "broken down" from pulling the cooling heatsink to do regular cleaning maintenance and they need to be replaced.
I have found thermal pads on ebay, but they come in all different thickness and I want to order the correct thickness.
Alright, my CPU is idling at 75c and my GPU is at 80c, I've opened up my M170 and It didnt seem dusty at all, so I went out and bought a small tube of AC5 which people say will help.
Now the problem Is I have no idea where to apply it, or how much is needed. I dont really know anything about hardware components, so If anyone has any pics which could show me where and how much to apply that would great.
The M170 is currently in peices at my desk and Im typing this on a MacBook, and I really dont want to spend anymore time on the OSX than I have to.
I'm selling my M1330 but need to reverse the copper mod. Do you happen to have the pink thermal foam pad around?
View 10 Replies View RelatedI have been reading a bunch of threads on decreasing temps and I am now thinking about changing the thermal compound that the machine shipped with.
I had originally seen a lot of people recommending Arctic Silver but I was not sure which one so I started to llok for more info and am now thoroughly confused. From what I have read some are designed for a more permanent mounting which I do not want since I may want to change the CPU in the future.
Also it seems some work better than others in certain applications which I don't understand. To me all it is doing is transferring heat so what it is transferring heat from shouldn't matter. But since it does seem to have some effect what has worked well for other SXPS 16 users.
My new SXPS 1645 arrives Monday and I have AS5 and cleaner handy.
I need to know where to apply AS5 and what to do about the motherboard chipset and GPU RAM. There are these thick sticky pads on those, do I peal them off and use AS5? Can I leave them on or do I need to replace them?
Ok so I am going to clean out my M1730 over the break and also going to re-apply thermal compound.
When looking at the various links for doing this , a number show pictures with the fan removed and my question is where I should and shouldn't be re-applying the compound.
I created this at dell ideastorm:
http://dellideas.force.com/ideaView?...00000000azJAAQ
On the forums, i constantly see people complaining about the heat their laptop produces. Some people (like me) who use their laptop on their lap a lot, prefer to have the fan on constantly, to keep the laptop cool to the touch.
Others, they hate the noise the fan produces so they prefer the laptop to be not so cool, but they want it silent .....
I already undervolted my computer which did help, but the fan is so weak now that I feel i need to do everything possible to keep it from overheating. Does anybody have an extensive guide on applying thermal paste?
I really need to do this. I am pretty noob at computer hardware, So i would need a guide that would even tell me how to take apart my entire case/etc... I am sorta running out of options.