I want to update BIOS using the supplied ISO image. I want to write this image to a usb and then boot from it, for updating bios. How to create bootable usb.
My system is E430, though the question is quite generic.
Today i installed window-8 Pro (64 bit) in my thinkpad E430 machine, but after installation its not charging, its showing PLUGGED IN , NOT CHARGING , its not charging beyond 33%.
View 5 Replies View Relatedwhat driver is missing for the unknown device with the following specs from the "Device manager"
General
- ACPI-Compliant Embedded Controller
- Drivers not installed error Code 28
device ID
- LEN0068
got every other device running with propper driver (WLAN, Ethernet, USB3.0, Intel Chipset, VCard(both), Touch scanner, Audio, Monitor, Camera, Bluetooth, Cardreader)
I bought a Lenovo thinkpad E430 recently with Windows 8 operating system. There is no print screen button in it even with Fn key. How to get print screen.
View 2 Replies View RelatedI have a problem with my battery on a brand new E430. I've used it for 1 week w/o problems and now it simply doesn't want to charge the battery anymore. It is stuck on 48% and I have a message saying "plugged in, not charging".
EDIT: I run Win 8 (64 bit) - absolutely everything is up to date, including BIOS.
How to get onekey recovery software for windows 8.1 . and i am using thinkpad e430 laptop.
View 2 Replies View RelatedMy laptop freezes for a couple of seconds randomly from time to time. The problem sounds like this one: [URL] .....But CC cleaner did not solve the issue.
The problem happens with almost every program such as microsoft word e.g. if I type and it freezes, the words will come out after it unfreeze.
Before the freeze, the laptop usually becomes very quiet then a few seconds later something spins and freezes the computer. I can assume that it is the HDD. However, the computer does not freeze every time the hard disk spins loudly.
When the disk spins loudly, the HDD activity spikes in task manager and the 'system' is the program that corresponds to the spike which is 'ntoskrnl'. However, the data transfer is no more that 0.1 MB/s during the spike.
I tried running in safe mode and I'm not very sure if it worked. The disk spins loudly much less often but the freeze did not seem to happen. Safe mode either tells me that it is a program/connecting to the internet/(maybe the system) that makes this freeze.
I tried a hard disk scan using lenovo solution centre and it found no problems. Also tried antivirus scan using windows defender and found nothing after a full scan.
Finally specifications:
OS: Windows 8
HDD: 1TB (upgraded from 750GB)
RAM: 8GB (upgraded from 4GB)
intel Core i5 3210M @2.5GHz 2.5GHz
Bios: v2.52
The 720p webcam in my new Edge E430 (I just got it last Thursday) is not working properly. When I use the Communications Utility or Skype, the green light next to the webcam turns on, but the image window only shows a completely black image. Also, when I increase the brightness or contrast settings of the webcam, the image becomes completely gray or completely white.
The Device Manager shows two devices - the "Integrated Camera" and the "Virtual Camera." I have already tried uninstalling/reinstalling the webcam drivers, but that hasn't worked. What else can I do?
I connected with the power plug and there was no green/yellow light next to the power socket. It seems not charging at all. Now it is forever dead. Tried to take the battery pack off, and connect it directly power plug, still dead.
View 3 Replies View RelatedI own one Lenovo E430. By now he is running Windows7, fully patched and updated. My issue is related with ultra-high touching sensitivity of the TouchPad. The TouchPad can react even on cloth touch.
This is problem for me, because I use TrackPoint, I don't have external keyboard and during high utilization extra unwanted clicks lead to unpredicted events. So, my question is how can I disable the Touchpoint.
I have purchased a new E430 ,, installed windows 7 ultimate 64-bit. I installed all drivers and all is working fine.. I still have one unkown device (PCI) .. I think it's VGA .. but I installed intel HD card driver.
below is the info:
The drivers for this device are not installed. (Code 28)
There is no driver selected for the device information set or element.
To find a driver for this device, click Update Driver.
device instance path:
PCIVEN_10EC&DEV_5229&SUBSYS_500017AA&REV_014&C587ECB&0&00E0
hardware ID:
PCIVEN_10EC&DEV_5229&SUBSYS_500017AA&REV_01
physical device object name:
DeviceNTPNP_PCI0016
I own a Thinkpad E430(type 3254). It's about 14 months old. Yesterday, it randomly started having an issue with it's keyboard. It acts like the enter key is continuously pressed, and about 1 sec after I hit any other key it stops. The enter key by itself has stopped working, and only shorts sometimes and results in a continuous press.
As soon as i boot, enter input is given and normal startup gets interrupted. If i press any key, it's normal again until an OS loads. For example, if i boot into debian, line breaks get inserted between the console messages that are displayed until i press a key, and if i boot windows, it gets stuck at the login screen because enter is given without the correct password so it loops. This behavior also happens sometimes randomly while working normally.
The keyboard hasn't even seen heavy usage, or any drink spills. I usually keep the laptop at my desk, and use an external keyboard. The last time I took it out was 2 weeks ago. I doubt it can be a software issue, so do I need a new keyboard?
Using windows 8.1 i've uptaded my intel hd 4000 drivers, restarted and lauched a 3d game. After few seconds I tried alt+tab and then everything got stalled and eventually with lots of artifacts on screen I've got a message about a system crash and that system now is dumpin information to a file and next it will restart. In that moment I've panicked and hard reseted (so memory dump hadn't finished).
So now when I try to boot - for a quite some time there is a black screen and then a list of boot options pops up:
Normal Startup , bios setup , boot menu .... but the keyboard is not working at all.
So after connecting a usb keyboard I entered boot options and there iv noticed something strange:
Link to image
EC version is messed up.
Keyboard is not working at all and some other things.
On top of that when I'm choosing normal startup the windows "wheel" is turning but its newer getting to boot.
I have an Ideapad Z500 with an W8.1 installed on it. I updated the bios to the last version but after that I can not control the luminosity level anymore. When I try to do it pressing the Hotkey it trurns to the lowest level of luminosity and I can only fix it by pressing the hotfix key when the laptop starts. I can not return to the old bios version. What shall I do?
View 2 Replies View RelatedI just bought an Edge 130 and wanted to set it up today. But I just can't enter the BIOS! I keep pressing F1 during the Lenovo splash screen. I've pressed it repeatedly, held it down, I even tried it with the Fn button pressed. Nothing worked.
I've have been working with and professionally supporting Lenovo (and before IBM) notebooks for over 10 years and not once did I have such a problem. This is only the second E-series notebook I have ever had. I bought myself an E525 last summer and had no such problems and at work we have T-, X- and W-series.
How can I enter the bios in a recently purchased Edge e530 ??
View 9 Replies View RelatedI just installed two new memory modules (4 GB each) but my laptop only recognizes one of them. I've tried researching how to change the RAM voltage in BIOS to see if that will allow the laptop to recognize both memory modules but can't find out how to do so.
How to change the RAM voltage in BIOS (specifically from 1.5V to 1.6V).
About half the time I boot up my laptop the bios hangs and I have to hard-reboot it to get it to work. Is there anything I can do?
View 2 Replies View RelatedI'm thinking of buying a Thinkpad E540 with a discrete nvidia gpu. I am planning to install linux on it and I don't really need optimus for it (nor is it well supported) but I'd like to occasionally be able to use it on windows.
I'd like to know if it's possible to completely turn off the nvidia gpu from the BIOS so it works only with the integrated intel one or should I buy one with intel gpu only.
I have read that the lenovo changed the dual gpu implementation on the latest generation thinkpads.
I recently bought a new E535 laptop working like a charm up to now. Bios access was possible by pressing Enter directly after switching machine one, than came some sort of POST analysis which could be skipped by pressing any key and than came some sort of table where I could access Bios by pressing some key (cannot remember which it was exactly). Alternatively I could enter Bios when in boot menu by pressing tab which switched to another tab where Bios could be entered (also some sort of diagnosis programs could be started). As mentioned in the subject it is impossible for me to do this now, after I did the following:
- exchanged built in HDD with an new SSD (Bios access yet possible)
- changed in Bios Setup boot mode from both (legacy + UEFI) to Uefi only (this might be the problematic point but I'm not sure)
- Installed Windows 7 in Uefi mode on ssd
No when I press enter on startup it brings me to Windows boot manager menu (you know where you can say start Windows normally or in safe mode and so). Boot menu also changed with a new "start windows" entry (well, this seems to be correct), but when switching to the other tab it is empty now, no entry for Bios setup or diagnosis tests anymore.
This is really bad. I have googled around and tried the following up to now without success:
- Pressing F1 instead of enter
- Shutdown laptop, and start with F1 pressed down
- starting without HDD
- starting unmodified HDD which was originally installed in laptop (which cannot be booted anymore, probably because it was installed in legacy mode)
I have also thought about flashing the bios, but the newest version available on lenovo support seems to be 1.04, but pre installed on my laptop is 1.10, so my version is a lot newer. Should I try to flash it nevertheless ?
I got a really annoying problem with my E330. It came without an OS, so I put Win 8 on the preinstalled HDD. Then I switched it out for a SSD and put Win 7 on it. (everything in UEFI mode)
Since then I can't get into the BIOS/UEFI anymore by either pressing Enter or F1. Pressing Enter still gives me a beep, but then Windows continues to load normally instead of showing several options like it used to do.
And yes I'm aware that I need a cold-boot in Win 8 to get into UEFI ... The only way to access UEFI at the moment is through the Win 8 charms-bar restart into UEFI trick.
I tried already to reflash the BIOS which doesnt work obviously since it's the same version, tried removing the CMOS battery, that gave me a one time opportunity to get into the UEFI with F1 when it complained about the date/time.
Switching to Legacy only leads me to an infinite PXE - something error loop, but I still cant get into the BIOS.
I tried pressing every combination of Fn+F-Keys and without Fn. Nothing works. I don't want to return the notebook, but it's a deal breaker for me if I can't get Win 7 running on it with accessible UEFI.
I installed new bios update downloaded from lenovo website (file h0uj03ww.exe). Immediately after succesful update message balloon popped up saying my battery is not genuine.
The battery is original, part of the notebook when i bought it and so far the system recognized battery as genuine.
Previous bios number was 1.12, new one is 1.14
Notebook model is 3259-C5G.
I am currently working on a ThinkPad Edge 15 0302-2BU for a client of mine. The system is able to POST and I can enter the BIOS but the UUID is all zeros and the Machine Type Model, System-unit serial number, and System board serial number are all blank.
I went to the support page for this model and downloaded the ISO file with bootable BIOS update utility for BIOS ver. 2.20 (82ET80WW) I updated the BIOS in case there were any issues with the current BIOS release. Rebooted then went to update the model number off the bootable utility. I entered the model number, Updated, and Rebooted again. Still having the same issue. The model number didn’t record after I punched it in.
I am still able to POST and get into the BIOS configuration. The system will not load an OS or boot off a CD into something like Windows PE.
I'm not sure if Windows not being able to load is due to the BIOS or not but I'm inclined to think so since I have trouble booting off CD.
I'm using a lenovo thinkpad edge e530.
I have a problem changing my BIOS settings after installing win8.1 and enabling bitlocker. I wanted to reformat the partition it was on, so I wiped it with gparted and now all settings in bios are greyed out and I cannot change anything. What can I do to be able to edit my BIOS?
I also have linux installed on my computer if I could do anything from there.
I have a HP touchsmart envy 15 and I am trying to restore computer to factory default. About 6 months ago, the computer said I could make a boot disc and be able to use that to restore my computer to factory and after I make the boot disc, I can delete the recovery partition as it will be stored on the disc. So I went ahead and make the disc (it turned out to be 4 discs) and the computer deleted the partition. Now I am here trying to use the discs to restore to factory, however, my optical drive isn't detected when the bios is booting. Because of this I need to turn those 4 discs into a bootable USB thumb drive. I have looked all over and there are many different ways of converting 1 disc into usb, but not 4.
View 1 Replies View RelatedI want to update BIOS on freshly bought HP 350 G1 notebook from F.11 to F.12 - which does have only FeeDOS installed. This is why (on my Lenovo) I downloaded URL... which is HP Notebook System BIOS Update, to create bootable USB to update BIOS. Now, after going through first few steps and getting choices what exactly I want to do, I get all options disabled.
After few hours of trying different things, all 4 USB ports (2x 3.0 and 2x 2.0), 3 different USB sticks I gave up and turned to you Why I want to update BIOS: To install Windows 7, because now It stops at a point that CD/DVD drive driver is not found and need to browse for it. On windows site it was written that updating BIOS.
After I updated the BIOS on M1210 the laptop doesn't start again. The power light start for seconds then goes off, I cannot hear the hard disk movement or any hardware except the power light....
View 10 Replies View RelatedMy new studio 15 (1555) arrived today and the instructions advised to update the computer with the latest Bios and drivers.
I followed the instructions and all was going well (I could see various things being downloaded) until my son clicked on a window that had popped up (believe it was from McAfee) and the computer switched off.
I went back to the Dell support to ascertain if everything had been downloaded properly and attempted to download the files again unfortunately I kept getting a message that no files have been selected .....
I have a problem with my Dell E1705. I would like to upgrade my BIOS but unfortunately i cant.
I try to upgrade from A02 to A09 with no results. Every time I try to do it the error was always popin up:
What you suggest to do? I try with different version on BIOS because i thought maybe it's impossible to upgrade from A02 to A09 but I have the same results
I even tried to downgrade to A01 the same I try to update to A02 which I already got. I had no positive results at all
My Acer V3-371 that I bought 5 days ago is slow after updating BIOS from v1.05 (when I bought) to v1.08 and v1.11.
I have checked hardwares and see that:
- CPU: OK
- RAM: OK
- Wifi, Ethernet, Bluetooth: OK
- HDD: NOT OK (see the attached picture) This situation usually occurs to halt the system for a while repeatedly.
(Both of OS Win 7/8/8.1/10 Preview and MS Office software are installed from the iso files downloaded from Microsoft websites)
I carried it to Acer Service Center, but they could not find out any problem with HDD and missed to check the compatibility of BIOS with HDD.