I upgraded RAM on my W530 and it's working only in single channel mode. How to enable dual channel in BIOS?
Here is screenshot about my RAM : [URL] .....
First, am I correnct in assuming all W530 will have bluetooth? Second, how does one enable it?
I can't see it under device manager. I don't see it when I do fn-F5. I have efi with win 8 with all metro features removed/disabled.
If I dont have bluethooth, can I transplant it from my W520 ...
I bought the i7-3520M (dual) and I looked in the manual to see what slots to use for my memory upgrade and the instructions were completely off (where the dummy stick is supposed to be and where it actually was).
I purchased two 8GB (Kingston) sticks to replace the 4GB that came installed. I took out the original 4GB under the keyboard and replaced it with the new 8GB Kingston. Everything worked great and I've been using it that way for about a week.
Tonight I decided to go ahead and install the other 8GB. I assumed it would go in the bottom slot where there's a dummy stick. I pulled out the dummy and placed my 8GB there. Turned the laptop on and... nothing. It wouldn't power on at all. I took my 8GB out and put the dummy back and it worked fine. Just to make sure I didn't get a bad stick, I replaced the one under the keyboard with my other 8GB and it worked fine there. My question is where is my second 8GB supposed to be installed and does that one dummy stick always stay where it is? It does have a "do not remove" graphic on it, but I thought it was only because the laptop came with one stick and if you were putting two in you would replace it.
I want to enable my RAM in dual channel mode... what is the process to do this? i have already checked in CPU-Z that it is currently in single channel mode.
View 1 Replies View RelatedIt seems I got the same problem that customers have with the T530. After removing the bios password I have no chance to get into the BIOS.
Bios Version: 1.11 (uefi only enabled)
OS: Windows 8 (x64)
I tried:
- Remove all drives (mSATA SSD, ODD, HDD)
- Press F1 at the Lenovo screen
- Tried all options in the Windows boot menu
- Pressed the Enter key at the Lenovo screen
Unfortunately there don't exist a BIOS update for the W530. So how I get into the BIOS?
Basically I am trying to install a new Samsung SSD into a W530, however, I can not get the Bios or Windows instalation to see it (when you select what drive you want to install windows on).
I can externally attach the SSD to my other laptop and see the drive. I can create partitions, format them, etc. But none of that worked my original issue.
I have also updated to the latest BIOS version, tried turning off UEFI, no luck.
What I am missing here to get this SSD to show up?
I recently upgraded my ThinkPad W530 laptop BIOS from version 1.11 (which it shipped with) to the latest, version 2.59.
After doing so, my two 16 GB DIMMS are not only showing up as 8 GB each, thereby cutting my usable memory in half from 32 GB to 16 GB.
I ran through all the normal hardware checks to ensure that one of the DIMMS wasn't bad. I tried each DIMM separately, tried in different slots, etc. They both show up just fine and even pass the memory quick test in the BIOS. Only, they are showing up as 8 GB DIMMs.
Is there a feature in the latest BIOS that would somehow limit this? It was working fine at 32 GB before.
And, unfortunately, there is no reverting back to BIOS v.1.11 from anything after v.2.55. It asked me if I was sure I wanted to proceed...this was the last type of problem I expected to see though. (I also tried reverting back to previous versions of the BIOS that were allowed and it didn't work...
I have a W530, with i7 and 16G standard setup. I want to enable HV-X and found they are marked as Disabled, and gray-out in BIOS, also date is gray-out also.
i7 must support virtualizaion, while time setting is gray-out, I think this is either a security issue or a BIOS bug, but I had same problem with 2013 Feb BIOS, and also update to 2014 latest BIOS, same problem here.
I just purchased a used Elitebook 8540w with i7 quad core and four memory slots (I love it!). It is running 64 bit Windows 7 Professional It came with one 4gb memory module and I purchased an additional 4gb module to bring total RAM to 8gb.
I have the HP document that shows for two 4gb memory modules, one should be in memory slot 1 and the other in memory slot 3 for correct functioning of dual channel memory. All set right?
Not quite. In the Elitebook 8540w, the primary memory slots under the keyboard are clearly labeled "1" and "2" However, the expansion memory slots on the underside of the chassis are also clearly labeled "1" and "2" Opps! There is no "3" and there is no "4" In which of the unfilled three slots do I install the second 4gb module for correct functioning of dual channel memory?
I have recently purchased a W540 and connected to my Dell u3011 30" monitor. I used the Dual Link DVI-D cable that came with the monitor and plugged it into my Ultra Dock. The maximum resolution i can get is 1920x1080? When i change over to a Display port cable i can achieve the full 2560 x 1600 resolution? Is there something i need to do in addition to achieve the full 2560x1600 resolution with the DVI-D dual link cable? I want to be able to connect 2 laptops to the one monitor and only have 1 display port input so i need to be able to use the DVI cable on the 2nd machine while still achieving 2560x1600 resolution.
View 1 Replies View RelatedI've got 2 separate but really annoying issues with my W540 20BH:
- display brightness keys not working: when waking up from Hibernation mode, sometimer (really, randomly!) the display brightness keys (Fn+F5/F6) don't work.... either if the display brightness is stuck on max, min or an intermediate level...Is there a way to shut down and restart the process which commands the Fn keys?
- audio channel commutation gets stuck. Normal behaviour of the audio configuration is:
1) speaker volume disabled, mic disabled
2) when plugging in a 4-pin headset, headset's volume is on, headset's mic is switched on; speaker volume is still disables.
3) when unplugging the headset, speakers' volume is still 0
After each boot, the audio channel is at 0, but doesn't commute to the headset when plugged in! I have to open Configuration Panel, realtek properties. With this window open, unplug and re-plug the headset. Now, the volume has its normal behaviour.
Any better way to configure audio channels and evenments, which is able to bypass realtek's manager?
Windows 8 came with this machine, and I have had performance issues for a month now. I have just soldered on till yesterday when I kept getting different blue screens and needing to restart...now it won't restart, and so I did the press enter to get to the troubleshooting area of the hard drive....selected the quick reset option, which failed, so I came back and selected the complete reset and it gets to about 65% and stops says there was an error and requiring a restart...this happened twice...now when it restart, it is trying to do a reset again...without me asking it to.
Is this normal? Normally I physically break a computer, and never get to the point where a reset is needed...so I am truly at a loss here.
It is a W530 and has 16GB of RAM. All I run/ran on it photoshop and Lightroom, Firefox, audacity, Roxio, Avast for virus protection, an online backup service, and a program called star stacker.
Is it possible to replace FHD TN matrix on an W530 (B156HTN01_1) with any good IPS matrix?
I'm really disappointed with viewing angles and colours.
Is there the ability to disable the touchpad on the W530? I don't see it as an option in the function keys. I am using a mouse and it's a bit annoying brushing my hand against it and having it mess something up.
View 6 Replies View RelatedI am looking to update my laptop used for photography. The ideal replacement looks to be the ThinkPad W530 with a dock and display screen. As the W530’s will be used away from home it and monitor will need to be calibrated.
I have been told I can only do this if the graphics card, NVIDIA Quadro K2000M, supports has more than one LUT to both laptop and stand alone monitors be calibrated.
I have had the W530 for several months now and it randomly powers off. This can occur when connected to the AC Adaptor, when running on battery, or when using the AC Adaptor without battery. Lenovo first replaced a fan, but that didn't solve. Now they are attempting to replace the system board.
W530, i7-3610QM, 1920x1080 FHD, 16 GB RAM, K2000 NVIDIA GPU, Muskin mSATA, 500GB 7200rpm, Bluetooth, Centrino 6300 AGN WiFi, Win8 Pro
I installed some Corsair Ram in slot 1 and 2 underneath the keyboard and after reinstalling the keyboard Ive noticed theres a gap at the top of the keyboard where it slots into the computer the whole way across specifically in the middle where theres alot of flex. The plastic which has the power and volume buttons seems to move around when pressed. This seems to be letting in dust and would especially allow a spill to enter the machine. This doesn't seem normal for a well built machine and have I installed the keyboard wrong?
View 9 Replies View RelatedI have a W530 (2436 CTO) ThinkPad purchased 11/10/13. It will not power up.While in use the screen went black, then the unit tried to reboot. Just as Windows began to initiate, the screen went black again. It immediatly tried to restart about three times in quick succession, about 3 seconds long each time. It was powered with the AC adapter at the time with the battery in place. I have tried all combinations with or without the battery or AC. In either mode, the power button lights up for approximately 1-2 seconds, then goes black. I have tried holding in the power button for 30 seconds. Nothing, other than about a 2 second light, then dead.
I have never received any power warning messages, low battery warning or the like. The only unusual behavior I've ever had is about half a dozen times I've had to do a hard power down. But not recently.I have tried the removing and replacing the SSD. I have removed and switched the two memory boards to test for a bad board or bad connector. None of these have solved the problem. I’m guessing the SSD failed, or perhaps a bad BIOS chip. I can easily replace the SSD, but 9 months of moderate use seems like a short lifespan for even an SSD. I can't update the BIOS (if that's the issue) because I can't get the unit powered up.
What type of screen is in a W530?
I have an FHD (I think) but when it comes to calibration I have the following options
CCFL
Wide gaumet CCFL
White LED
Red LED
OLED
Plasma
RG Phosphor
I purchased the W530 with the 120GB SSD option. Windows 7 takes up more space than I had expected, and now I'm looking to increase the amount of memory on my laptop.
Will buying the hard drive bay adapter from Lenovo and another HDD do the trick?
Product that I'm looking at: [URL] .....
I recently acquired a new Thinkpad W530 with Windows 7 Pro.
I want to immediately replace the 500gb main drive with a larger one. I plan to do this by imaging the system partition of the current drive to an external USB hdd, and then then writing the image to the larger one after it's installed in the W530.
My question: Can I then just store the original drive away as is, to use for recovery (should the need arise), in lieu of creating recovery media now?
It seems pretty clear the answer should be "yes," but since I've always used XP up until now I'm wondering if there are any kinds of Win 7-specific watchouts (maybe licensing-rleated?) that would keep things from being as simple as popping the original drive back in the main hdd slot to get things back to exactly where they are today?
All, I am having a major problem with VMWare and the W530 "Num Lock". When I move the cursor into the VMWare window a message comes on say "NUM LOCK: ON" when I move it out of the VMWare window I see message "NUM LOCK: OFF". I do not have any key on the keyboard to disable Num Lock. There are utilities I can run in the SUSE VMWare image to capture the key binding and remap, but I do not have anyway of turning Num Lock on or off to capture the key binding.
View 3 Replies View RelatedSimilar to a post about the T530 I used to record streaming audio (internet radio, youtube, playback etc.) with Snagit on my old computer, now on new W530 I cannot find "line out, mono out, wave out," devices to record from, only "microphone".
On the Lenovo W530 using Windows 8 Pro I followed the follwoing steps posted elsewhere for the T530:
Control Panel > Hardware and Sound > Sound > Recording ... right-click to check Show Disabled Devices, then choose Stereo Mix as Default (may also want to right-click on Stereo Mix and double-check Properties: make sure Listen level is not at zero)
After showing disabled devices on the sound > recording tab the tab still shows only one device, the "Microphone".
If it is possible how on Windows 8 or the W530 (and possibly other models) do we get the line out / mix out / mono out / whatever they call it for the sound that comes out of the computer?
I have been told by sales that the W530 will NOT support SSD's larger than 256GB. I wonder if it is sales gimmick since the SSD uses the SATA3 interface that works with standard drives > 256GB. But before I go on a limb and buy a big SSD, I need to verify if I am wrong.
Using a 480GB or 512GB SSD drive in the W530 thinkpad?
My W530 suddenly stopped communicating with my MS Bluetooth Notebook Mouse 5000, and nothing I try will bring it back. It does not show under Bluetooth devices, and it will not find anything when I search for devices. I know the mouse is not at issue, as it will readily pair with an Android device. Yes, the manual wireless switch is turned on. Yes, it is turned on in the Fn+F5 OSD. I've done a BIOS update. I've updated my system using Lenovo System Update. I've checked power settings both under driver properties, and in my power plans. Everything seems to be in place, it's just like the Bluetooth has vanished, but the system doesn't know it. Yes, I'm POSITIVE my system has Bluetooth... I've been using it for the past 6 months or more.
Recently, I've experienced issues with the mouse losing connection for a few moments at a time, but nothing beyond that. Then yesterday, It's completely gone, and I can't get it back.
W530 i7-3840QM, 16GB Ram, FHD 1080p, Quadro K2000M, Ultimate-N 6300, Win7 Pro 64-bit, 256GB mSATA, 256GB SSD, 1.5TB Ultrabay Drive
I bought my W530 with Windows 7 preinstalled and an option to upgrade to Windows 8, which I did immediately before installing any programs. When I now try to upgrade to Windows 8.1 I get a message asking me to previously uninstall RapidBoot. However I cannot find RapidBoot on this machine. How can I uninstall it?
View 6 Replies View RelatedI have a feeling that I am missing something very obvious here, but I have looked everywhere and cannot find the Bluetooth services on my laptop (W530, Windows 7 Pro 64 bit, ThinkPad 1x1 11b/g/n Wireless LAN PCI Express Half Mini Card Adapter for Windows 7).
When I do FN + F5, I get the Lenovo Wireless Radio menu, but it only lists Airplane Mode (off) and 802.11 Wireless (on).
I have check BIOS security settings for I/O devices and Bluetooth is enabled. However I cannot find any references to Bluetooth under Device Manager ->Network Adaptors.
Is it possible that this laptop is not equiped with Bluetooth?
Yesterday I bought a little 22" Vizio VW22L television to use as another monitor for my W530. I'm using this cable: [URL] to connect my computer to the TV. When I connected it at first it worked fine for about 45 minutes then I just got screen noise (short, multicolored vertical bars moving everywhere). Now whenever I try connecting it I get my computer's display on the TV for a couple minutes, then the screen noise again.
I was wondering what the issue is or could be. The cable seems to work fine. I tested it with a Magnavox television and a different Vizio TV. This TV's HDMI port also seems to work fine. I had my brother connect his Samsung Series 3 to it via HDMI and it ran perfectly well. The Lenovo update utility says all my drivers are up to date, as does Windows update.
I have just boight my first Lenovo - a W530 Thinkpad notebook.
The integrated camera works well... but I can ONLY take picture with it.
Is it possible to record some video with the camera? Do I need to install any software or driver?
- Win7 64bit
After receiving my w530, I wiped the drive and installed a nice fresh copy of Windows 8 Enterprise (volume licence work copy).
I have installed all the latest drivers, etc. and taken note of the various documents about Windows 8 upgrade/install, but cannot make use of the integrated camera?!
The driver is listed under the device manager:
Imagine Devices -> Integrated Camera (Ricoh 1.0.0.19) - BTW I tried the beta one to see if that worked, and it made no difference to I rolled back to the proper release again.
The docs I have read said NOT to install the Communications Utility, and at this point in time there is not a Windows 8 listed compatible version of that. I did give it a try when the camera did not work, but although there were no errors, etc. it didn't work either ...
Skype/messenger/windows 8 camera seem to know it's there, but cannot make use of it (I get the placeholder image).
Under Control Panel->Hardware and Sound, there is no appropriate entry for me to toggle/configure.
I see the green light come on, but no picture. Running latest bios G5ET65WW (2.07).