I have an acer aspire 1681wlmi which has just finished its extended 3 year warranty. The problem started by freezing upon start up on a white screen then the freeze up got quicker and quicker each time i rebooted it. Now the power on starts the hd, everything flashes like normal and after 5-6 seconds the hd stops and the hd light goes out. It wont boot from cd, it tries, the cd spins then everything goes dead again. I have tried all the previously mentioned fixes mentioned on this forum like removing battery, memory etc, i even tried to dismantle the whole thing but when it got down to the motherboard i did not want to break anything and put it back together again. I havea feeling the mother board is dead....
I have a Acer E1 522-3657 computer, which my son set-up for me but did not make the recovery disc(s). The unit is just outside of the warranty period when the hard drive failed. The hard drive just makes a clicking noise and after the logo screen appears it goes to a blue screen with a box that has the following message with in, "Default Boot Device Missing or Boot Failed. Insert recovery Media and Hit any key.....Then Select 'Boot Manager' to choose a new Boot Device or to Boot Recovery Media.
I have installed a brand-new Western Digital 1T Sata3 harddrive to replace the Toshia 750 GB original Drive. After turning the computer on and at the logo screen I press and hold F2, this takes me to the InsydeH20 Setup Utility Screen. I see under the "Information" menu that the installed harddrive model and serial number appear. I see in the "Boot" menu, Boot Mode: "UEFI" and Secure Boot: "Enabled".
Under the "Exit" menu, Exit Saving Changes is highlighted. When I press F10 a "setup Configuration" box appears asking to save configuration changes and exit now? "Yes" is highlighted to which I hit Enter and are returned to the "Default Boot Device.......page. I then hit ecs twice and are at a black screen with the message No bootable device -- Please Restart system_appearing in the upper left corner of the screen. I then push and hold the power button until the computer shuts off.
I have ordered from acer the "Acer E-recovery Media Disc Set", which is specific to the SNID of my computer. I have not attempted to format the new hard drive in any way. I assume the E-recovery Media Disc Set will handle that operation due to the multiple partitions required.
In view of the above situation, do I need to set up the computer in any way before I start to utilize the E-recovery Media Disc set. I assume the Media will be on CD's. The computer was running Win 8.0 which was updated to Win 8.1 and was running very well, very stable.
Acer V5, spilled coffee on keyboard. no problem at first, then lockup, and on restart get the No Boot Device or Boot Failed. Am using my old laptop now. Can I get a download, save it to thumb drive, and use it to restart/reboot my Acer?
I have loaded Kaspersky anti virus on my computer, the computer gave me a driver alert and restarted, now the bios screen does not display at start up and the hard drive light does not come on, the only thing that seems to be work is the CPU fan.
Machine is an Aspire 9301AWSMi running XP SP2 rather than Vista.
On boot, the machine shows the ACER BIOS screen but after that the display just goes blank. Have tried to boot from the Windows XP CD and the only difference is that following the BIOS screen I then get a message saying "Windows is inspecting your hardware configuration" and then a second or 2 later, back to a blank screen. No disc or CD activity.
Is this another ACER Motherboard problem or maybe a HDD failure?
After I turn on the power, the harddisk led doesn't turn on, just the CAP and NUM led flash once. The screen doesn't turn on, even the Acer logo doesn't appear. I can hear something is turning inside the notebook, but it's definitely not the harddisk.
I wonder if I had pressed some wrong buttons, and disable the notebook.
The laptop has been working fine until yesterday...the screen froze and wouldn't let me use the mousepad/curser. I turned the machine off and rebooted, it won't reboot, reacts for about 2 seconds, screen stays black and nothing. Do you think my processor is shot or thoughts to possibly fix it?
i wan to format an acer aspire 2920. I shut down the pc and put the recovery cd in but the system still opening a windows and didnt read the CD. and i didnt saw this word "press any key to boot from CD". How do I get it to boot from the cd-rom. I went into setup to change the boot sequence to boot from cd 1st but cd isn't listed as a boot option. It has HDD, ODD, USB, PCI LAN as boot options to select from in that order.
My 17 mth computer suddenly had a blue screen with error messgae PAGE_FAULT_IN_NONPAGED_AREA ......etc it told me to push F8 to open in safe mode which I did but nothing happened! I turned the computer off and now it won't open up again. The power registers but the screen stays blank! Anyone got any suggestions or is it past hope?
I have tried to contact ACER U.K by e-mail but it won't accept my message as it says SNID number should not exceed 11 digits but it's actually only letting me put in 3 digits! I've also tried to ring but every number is coming up invalid or 'mail box full'.
I'm having getting my USB stick recognized as a bootable device (installing windows 7 onto a system that came with windows 8.1 pre-installed, no optical drive)
System: Acer E 15 (E5-571), BIOS V1.15 (UEFI)
What I've tried:-Disabled Secure Boot -Created bootable USB stick with Windows 7 iso, via 'Microsoft USB/DVD Download Tool' (on alternate Windows 7 system) -Created bootable USB stick with Windows 7 iso, via 'Rufus' (on alternate Windows 7 system) -Windows 8.1 Advanced Restart -> Boot from UEFI USB Device (No UEFI device recognized)
What worked:-Enabling 'Legacy Boot Mode': USB stick was recognized upon boot and loaded Windows Installation. HOWEVER, Windows 7 won't instal to a GPT formatted drive under Legacy Boot Mode. I've read booting in UEFI mode is the only way to get Windows 7 to install onto GPT.
What I don't want to do:-Format the drive, change drive mode to MBR to instal Windows 7. Why? Because then I'd loose the factory installation of Windows 8.1
I want to be able to boot from a USB thumb drive/stick. There is no option in the Bios setup to do this.I will have to return the system to the store - but what Acer system can I replace it with to boot from USB stick?
Aspire 5920. When I purchased it from a chain electronics store, I did not receive any OS CD/DVD or any other disks with it. Now it got to the point where it had slowed down to a crawl, I went to do a system restore (Vista Home Premium) to the earliest point which was set on 24 Aug 09, and I when it went to reboot itself it is now stuck on Start Windows Normally and if I select it, it just cycles back to Start Windows Normally after about 15 seconds. I've been doing that for the past two hours. I've hit F5 to get to a screen that allows me to choose F8 and get to safe mode and other selections and all of them take me back to Start Windows Normally and the endless cycle from hell. Of course I have no CD to boot from, so I have no choices at this point. The extremely curious thing is that I know another couple of people who bought the exact same model from the same retailer and none of them got disks. The retailer apparently told one of them that Acer doesn't ship OS disks with this model. I find that hard to believe.
I have a brand new Acer Aspire 5536. It came pre-installed with Vista which I have repalced with Windows 7. I did a clean install, first formatting the hard drive.
The boot process takes 7-10 minutes before the login screen appears. Once logged in the sysrtem appears to be working fine. I have re-instaslled multiple times (using different disks) but no matter what I try it takes an age to boot.
Could my laptop be faulty - does anyone else have Win7 running on one these?
I have problem with my Acer Aspire 7520G. When I turn it on, after memory check and disk check I got messages:
Resource Conflict PCI Serial Bus Controler in slot 01 Bus:01 Device:04 Function:00 ERROR Bus:01 Device:04 Function:01 ERROR Bus:01 Device:04 Function:02 ERROR Bus:01 Device:04 Function:03 ERROR Bus:01 Device:04 Function:04 ERROR
after this wont boot neither from HDD nor CD/DVD. Just blink currsor apears.
After a few of restarts, if I got luck, it will boot up "normally". I checked in Windows system that Bus 01 Device 04 is acctualy
Ricoh 1394 OHCI Compliant Host Controller at Function 00, SDA Standard Compliant SD Host Controller at Function 01, Ricoh SD/MMC Host controller at Function 02, Ricoh Memory Stick Controller at Function 03, Ricoh xD-Picture Card Controller at function 04.
I recently updated my bios on my R7-571 and it has caused me great woe. My computer will lock hard between 3 min and 3:30 min after bootup if I don't disable the WIndows Managment INstrumentation service. THis of course caused other problems on services that depend on that like LogMeIn. I need a solution to this. Either a way to downgrade to an earlier bios which I don't think is possible without a version of the bios updater that will support this, or a newer bios that addresses this issue.
Bought this notebook on Oct.30/14. Used it this past Friday; was working fine. Plugged it in for the night and the next day, I noticed the fan was running and I wasn't able to boot it. It won't shut off using the power button on side. The only way to shut it off was by using a paper clip on the reset on the bottom of the notebook.
Aspire 7540-1284 Shut it down. Went to turn it on and the blue lights are working but it just lets me know the Hd is there but then gets quiet - nothing shows on the screen. It's 5 years old and I just reinstalled Win 7 Pro this week. I removed the battery. Same thing. I put the HD in an external case and hooked it up to another laptop and it is fine.
2 days ago I had trouble accessing the internet on my E1-570. Windows Explorer kept throwing up a fault and restoring the page. Eventually I loaded Safari and then Firefox and resolved to sort the problem with Windows Explorer some time in the future. This may be unrelated to what happened the next night. Started the E1 and got the usual "Acer, Explore beyond limits" screen and spinning dots, then got the login screen - input password then return. Spinning dots for much longer than usual then blank screen. I can see the cursor arrow so the screen itself must be functioning. Lights on the front are working - AC, battery and HDD. I have had the machine 14 months and it is used exclusively at home so has not been roughly treated.
I'm having an Acer Aspire 4736Z which is cannot boot.
When I power on it there's power light but screen blank. No HDD activity.
And I copy Bios files to my Transcend thumbdrive and enter BIOS recovery mode by pressing FN+ESC, the whole screen turn white and fan running fast! But power light no blink, Thumbdrive no power and activity.
I booted up my acer aspire 7520 and checked my email then left the room.When i returned the laptop was switched off so i tried to reboot it.Unfortunately it will not boot up anymore,it begins to boot but then switches off and then tries to reboot again.I can no longer access the bios as the boot cycling prevents it.I thought it may have been a hard drive problem so i replaced it with a new one but this has the same effect.The RAM cards have been removed and tried in different slots and this hasn't helped.The only way to stop the laptop from cycling through is to remove the battery.This fault occurs both when trying on battery power and on mains supply.The battery is getting charged ok.Has anyone on this forum ran into this problem before? I have searched on the net for clues on how to fix this but have ran up against a brick wall.There are lots of people who have had this problem but i haven't found a fix yet.The laptop is running Vista home premium.
I installed Windows 7 Home Premium 64-bit on my Acer Aspire AS1410. Maybe it's normal, but the hard drive LED is solid on for about 30 seconds before it boots into Windows 7 during the floating windows screen. Is this normal?
I have recently bought laptop acer aspire 6930 g with following features Processor intel core 2 duo t6400 2ghz 2mb cash Ram 4gb ddr2.
Hard disk 1000gb ( 2 hard each one 500gb) and preloaded vista home premium and nividia 9600m gt 1gb ddr2.
And i notice that my laptop take too long boot time in compare with my friend laptop Dell inspiron 1525 with 1.6 pantium dual core processor and 2gb ddr2 ram and 160 gb hard disk and windows vista ultimate..so is there something wrong with my laptop and how can i speed up boot time and do u think that i can play games like crysis and call of duty 4 and GTA 4 on it?
when my girlfriend tries to switch on the above laptop it seems to boot up but there is just a blank, black screen. If you look very, very closely the desktop display seems to be there but we don't know how to change the colour/contrast etc. Is it as simple as that do you think or is the problem deeper. I've tried everything I can think of; I've thrown water over it, hit it with the cat and punched it. None seem to work.
My Acer laptop died on me sometime last year, I tried to fix it, had somebody who is more techie than me look at it and we couldn't fix it. He managed to get all the data off but couldn't get it to boot up.
My brother recently had a similar problem with his desktop computer so he told me to put an XP disc in and change the BIOS so it booted from the CD ROM.
I have done this and it wont boot. It doesn't seem to recognise there is a disc in there.
When it loads, the Windows XP screen comes on, then a blue screen flashes up, can't read what it says as it doesn't stay on long enough, then the Acer screen comes up then the screen asking if you want to start up in safe mode etc comes up, if I select start as normal or from last know good configuration, it just keeps looping but if I select safe mode, a huge list of drivers comes up then it turns itself off.
I have tried to do the built in recovery but it doesn't work, just stays on please wait for hours.
I have been working on computers for almost 20 years and this has me completely confused. My Aspire V3-571-6643 laptop was working fine until just recently. The system will power on and show the Acer screen and then immediately reboots. It will stay in this reboot loop until manually stopped.
I cleaned and reseated the RAM module and also tried it in both slots with no change. I was able to access BIOS and determined the drives and all settings are correct and even reset to factory defaults with no change. I then pulled the HDD to use in a docking station to determine if the drive was salvagable. Everything reads fine and passed both short and long tests via SeaTools. With the HDD installed the system won't try to boot to CD/USB but after removing it the system will boot to CD just fine. I then ran a full scan using Eurosoft Pc-Check and everything is fine. I reinstalled the HDD and immediately get the reboot loop again.
At this point the mainboard and HDD both test fine independently but will not work together. My only guess is that the mainboard is no longer supplying enough power for all of the components and crashing when the HDD tries to spin up on boot. That, or the SATA controller is malfunctioning and only working for the ODD.
The original hdd was stopped functioning on my aspire v5-431. I try to put in other laptop but wont spin at all. The laptop was preinstalled with Windows 8 UEFI and safe boot on or something like that and gpt partition i guess and now i can not boot or enter in bios, how to flash bios or to install on this new hdd windows 8.
I tried everything from removing the motherboard batteryto boot from usb with bios file and Crisis files and nothing. The f2 button doesn't work and acer crisis recovery ask for wph file format and i just have rom file format.