I have a Acer E1 522-3657 computer, which my son set-up for me but did not make the recovery disc(s). The unit is just outside of the warranty period when the hard drive failed. The hard drive just makes a clicking noise and after the logo screen appears it goes to a blue screen with a box that has the following message with in, "Default Boot Device Missing or Boot Failed. Insert recovery Media and Hit any key.....Then Select 'Boot Manager' to choose a new Boot Device or to Boot Recovery Media.
I have installed a brand-new Western Digital 1T Sata3 harddrive to replace the Toshia 750 GB original Drive. After turning the computer on and at the logo screen I press and hold F2, this takes me to the InsydeH20 Setup Utility Screen. I see under the "Information" menu that the installed harddrive model and serial number appear. I see in the "Boot" menu, Boot Mode: "UEFI" and Secure Boot: "Enabled".
Under the "Exit" menu, Exit Saving Changes is highlighted. When I press F10 a "setup Configuration" box appears asking to save configuration changes and exit now? "Yes" is highlighted to which I hit Enter and are returned to the "Default Boot Device.......page. I then hit ecs twice and are at a black screen with the message No bootable device -- Please Restart system_appearing in the upper left corner of the screen. I then push and hold the power button until the computer shuts off.
I have ordered from acer the "Acer E-recovery Media Disc Set", which is specific to the SNID of my computer. I have not attempted to format the new hard drive in any way. I assume the E-recovery Media Disc Set will handle that operation due to the multiple partitions required.
In view of the above situation, do I need to set up the computer in any way before I start to utilize the E-recovery Media Disc set. I assume the Media will be on CD's. The computer was running Win 8.0 which was updated to Win 8.1 and was running very well, very stable.
Acer V5, spilled coffee on keyboard. no problem at first, then lockup, and on restart get the No Boot Device or Boot Failed. Am using my old laptop now. Can I get a download, save it to thumb drive, and use it to restart/reboot my Acer?
My Ideapoad P500 is approximately 16 months old (so the warranty period is out, obviously!) A couple of nights after a reboot I got the message "Repairing Hard Disk errors. This could take an hour or longer."... or something very similar. The laptop hung up at that message for more than 18 hours.
I did a hard reboot and now get the message "Checking media" followed by the error "Boot failed." This leads to the message, "Default Boot Device Missing or Boot Failed."No I don't have any recovery media.Yes I have pretty recent backups so that is not a problem.I've got an enclosure that I can use to hook my laptop hard drive up to so I can see if the drive is even readable.
Now here is the 64 thousand dollar question... how do I get the hard drive out of the laptop? I have taken the five screws out of the back. At that point, I think the DVD drive should slide out, but it does not.how to get the hard drive out?
I have a y500 Lenovo gaming laptop with Windows 8, and for the past couple of days, each time my laptop is put in hibernation or powered down, whenever I turn it back on it gives me this message:
"Default Boot Device Missing or boot failed Insert recovery media and hit any key Then select boot manager to choose a new boot device to boot or recovery media."
Then it brings me to a page with 3 boot options, and only the Windows Boot Manager works. I'm doing scans and hardware scans but so far nothing is being found. This laptop is less than 2 months old so I really don't think it's a hardware problem, and I haven't downloaded anything recently that may have messed this up. I would contact Lenovo but I'm unsure if this is an issue with the laptop, or Windows 8.
I get the error in the Title after i tried to flash the latest BIOS update for the Z510. I can press ok and then get into the boot manager but i cant choose anything there. Also I cant boot from a Disk with e.g. XP on it.
I also tried the Inside BIOS crisis mode (fn+r) with the BIOS file on my USB drive but it doesn't work and tries to access the file on the USB drive but boots normally instead to the error again. (Couldn't try it with removed battery as I have to remove the whole back to remove the battery on the Z510).
Yoga 13 bought in 2012. Was working fine with 128 GB / 4 GB. Tried adding another SSD and 8 GB RAM (Crucible), and now I get the message "Default Boot Device Missing or Boot Failed. Insert recovery media and select any key."
I went through the bios and Information says "Hard Disk: Not Detected". Have tried F9 factory reset. No response. What else can I do?
I have HP Pavillion g4 windows 7 64 bit laptop.I had installed android tool kit and restarted my laptop.After that my laptop is not booting UP.I am getting below error "Status: 0xc000000f".
Windows Failed to start. A recent hardware or software change might be the cause. To fix the problem:Insert your Windows installation disc and restart your computer.Choose your language settings, and then click "Repair your computer."If you do not have this disc, contact your system administrator or computer manufacturer for assistance.Status: 0xc000000fInfo: The boot selection failed because a required device is inaccessible.I dont want to lose the data.I dont have windows 7 installation CD.How do I resolve this.
I have a Pavilion dv7 1245dx with Windows Vista 64 Bit bought 2009 at Best Buy. It slid off the arm of the couch onto a carpeted floor while shut down. Next day started ok, got into yahoo, facebook, then kind of froze up. Eventually, would not do anything, manually shut it down, started it back up. Black screen, 'No Bootable Device-Insert Boot Disc And Press Any Key'. It will not accept recovery discs that I made after purchase. Start up test ok, memory test ok, hard disk failed 'Boot Drive Not Found'. Caps lock light is blinking. I saw something in a forum about resetting or reseating the hard drive but no explanantion how to do it.
I have problem with my Acer Aspire 7520G. When I turn it on, after memory check and disk check I got messages:
Resource Conflict PCI Serial Bus Controler in slot 01 Bus:01 Device:04 Function:00 ERROR Bus:01 Device:04 Function:01 ERROR Bus:01 Device:04 Function:02 ERROR Bus:01 Device:04 Function:03 ERROR Bus:01 Device:04 Function:04 ERROR
after this wont boot neither from HDD nor CD/DVD. Just blink currsor apears.
After a few of restarts, if I got luck, it will boot up "normally". I checked in Windows system that Bus 01 Device 04 is acctualy
Ricoh 1394 OHCI Compliant Host Controller at Function 00, SDA Standard Compliant SD Host Controller at Function 01, Ricoh SD/MMC Host controller at Function 02, Ricoh Memory Stick Controller at Function 03, Ricoh xD-Picture Card Controller at function 04.
I have an acer M3 581T which I bought about a year ago. Now, windows crashed and said there was a file missing. I am no longer able to boot up the system, I've tried the erecovery (alt f10) but it just proceeds and says it's not able to boot. I have no recovery cd/usb at hand. It is of my understanding that this ultrabook has two harddrives. One SSD on which the operating system is installed and one HDD with the other files on.What do I do to make it work again? I do not care if all my files are lost.
I have an acer laptop e1-571 with windows 8. the mb failed ordered a new one installed it. on boot now i get no bootable device. The bios shows the hard drive and its the first in the boot order. If i hit f12 after powering on to access boot options the 3rd choice is efi device windows boot manager. If i select that it boots normally and runs fine. is their a way to boot the machine without having to hit f12 every time and selecting efi device to boot to windows? i tried updating the bios as well.
I have upgraded to Windows XP and reinstalled all the drivers I need from the Acer website. Wireless networking is fine.
The problem is, when I slide the Bluetooth switch on the front of my computer while a device (Nintendo Wiimote) is waiting to connect to the computer, "No Device" in green text shows up on the bottom of my screen. I think this shows the driver is somewhat working and the hardware is detected. The LED indicator beside the switch does not light up.
I go to my control panel and double click the "Bluetooth Configuration" icon, nothing happens for a while, then a single dialog shows up saying "Bluetooth device not found. Please verify that your Bluetooth device is properly connected and turned on." showing only an OK button.
Inside the computer management window, under device manager, a group called "Bluetooth Devices" exists, and inside is something named "Bluetooth Bus Enumerator". I have right clicked on both and tried "Scan for Hardware Changes" and nothing happened. The properties show that "This device is working properly"
Drivers Provider is Broadcom 1/11/2006 Version 22.214.171.1240
Yes I have restarted my computer several times. All of the above actions were performed four, once with my finger holding the switch and once without, then again with the Wiimote in a waiting-for-connector mode.
My Wii is turned off with the power supply unplugged, there are no other devices with Bluetooth in my house.
how to get Bluetooth working.
There are other problems with this laptop, the card reader only supports SD cards, not Memory Sticks or xD cards. That's a problem for another day. However I would never recommend this laptop and this brand to anyone, but it was pretty cheap.
so im going around to install windows 7 through boot camp, got my blackbook ready, i must know which OS will boot by default if i dont touch anything? or am i doomed to hold the option key or something every time? just started installing snow leopard too
My Problem: Can't boot from second drive by default
I have an HP Pavillion dv7 1451NR, product number NV204UA#ABA.
I have two drives installed. I have Windows 7 64-bit installed on drive 0 and Ubuntu 32-bit installed on drive 1.
I can successfully boot either operating system by the following procedure:
Power up Press escape-key to get to BIOS Press F9-key to get to boot menu Boot menu shows two drives named “Internal Hard Drive” If I select the first entry named “Internal Hard Drive” I boot to Windows 7. If I select the 2nd entry named “Internal Hard Drive” I boot to Ubuntu.
I power up if I do NOT press escape, the machine boots to Windows after the timeout. My Problem: I want to boot to Ubuntu by default.
I've checked the HP bios and I don't believe there is any way to do this by changing the boot priority in BIOS. The BIOS doesn't seem to differentiate between the two hard drives. I only has one entry for “Internal Hard Drive”.
I believe an approach that should work is:
Use bcdedit or easybcd to create a BCD record that points to GRUB. Create a GRUB config file that “chain” loads Ubuntu. Use bcdedit to move the GRUB entry as the default. I've tried various permutations but can't get it to work.
How do I discover where the initial boot image is for GRUB?
I'm trying to boot from legacy boot from my new dell 7000 series. however when i change from uefi to legacy i have no boot option. the whole boot list is empty.
i have called dell and the support desk told me dell has no support for legacy :S that means no windows 7 on my dell or any other os that uses non uefi...... i think the bios is corrupt is the whole list is simply missing.
I swear it is always something with this product. I made a bootable USB flash drive and put Windows 7 on it. I have 2 M1330's, the only difference between them is CPU/RAM/HDD. One of them boots just fine off the USB drive, the other doesn't. They are both running the A15 BIOS. What am I missing here? I've compared the BIOS settings side by side and they are identical.
I got this laptop a few days ago, I currently have 7 and XP installed on it and kind of have vista...(read further down).
My 7 seemed to break today after playing around with a program called powerstrip trying to get my external monitor to show the right resolution (I've realised now the cable vga was broke, but meh) but this is not the full problem, after windows 7 failed to boot I tried to boot xp after turning it off during the windows 7 splash screen and now im stuck with a dash when I turn the laptop on (I dont know if its actully related to something I've done or not).
If I turn the laptop on a flashing dash comes on in the top right, it then stops flashing and turns into a none flashing dash further up the screen and just locks here and I cant do anything at all other than trying to restart it. When I had this problem previously (at least I think this problem) on my desktop it usualy turned out to be something usb related but I have everything unplugged (all though the bluetooth adapter light is on when it is doing this) so I realy dont know what to do...............
my dell inspiron laptop model n5030 will not start. when you turn it on the startup repair window comes up. after the diagnostic runs it says windows cannot repair this automatically. my warranty expired this past august and now my laptop died. how do i restore my laptop when the system restore partition does not work? it just says. boot manager failed to find os loader error code 0x3. and it also says boot configuration data store repair failed. error code = 0x2. then the laptop shuts off. what should i do? i have only had the laptop a year and a half. do i need a new one?
So I got the blinking folder with a question mark when the macbook tries to boot up. A quick google search said something about missing boot files and booting from a CD.
The macbook wasn't bought new from Apple and I don't have the install CD that came with it. Can I use the install CD from another macbook? If so, is there a stipulation as to which version of OS X install CD I can use?
I can't and don't remember what version of OS X I have on the computer that is having problems. Is there a way to find out?
This Compaq CQ50-NR215 has continued to get slower over time. It was bought at BestBuy, and came with (2) "GeekSquad" recovery CD's- as opposed to a Microsoft OS disk? Upon backing up my data, I proceded with Disk1- which it said successfully did something with the partition. Stage two was installing original software. It stalled during this stage & gave ERROR 1005. After removing the CD, the laptop failed to boot, stating that some device in the boot sector was not present.
It so happened that I had a Vista OS CD from some other computer, so I inserted the CD & tried reboot. After asking whether to repair/install windows (which I selected install), it appeared to going well. The greeting message appears & says "Prepearing your DESKTOP for initial use". It booted fine, the UI appears intact. The problem-
The WLAN light on the laptop which is red when turned off/blue when on- remains red & will not activate. In the device manager I find no network adapter. A section named "Other Devices" is highlighted in yellow indicating an issue- when selecting Other Devices, a submenu appears & the following list is present (see photo also)
Coprocessor Ethernet Controller SM Bus Controller Unknown Device.
From the HP driver download section, I downloaded what I thought may be the appropriate chipset to a flash drive, then moved to the laptop & installed. Still nothing.
It was suggested that I may be able to plug an ethernet cable directly from my router to the laptop & gain internet access that way- which failed, no access. The CD I installed from was designed for an older desktop, not having the software to make use of the internal wifi.
I have an HP envy 14 beats edition that has a corrupt or missing boot files. The instructions are very simple, enter your windows cd, select language, and then repair. What if my laptop didn't come with a windows cd, just a recovery cd? How do I repair my files. Can I download the files somewhere to boot up and repair my laptop os?
I have loaded Kaspersky anti virus on my computer, the computer gave me a driver alert and restarted, now the bios screen does not display at start up and the hard drive light does not come on, the only thing that seems to be work is the CPU fan.
I had to install a new hard drive onto Dell Inspiron 17R (5720, Mid 2012). Ordered new hard drive from Dell, and also Operating System reinstall DVD. Windows was loading, but computer shut down and did not restart. I pressed the power button to restart, but now get 'BOOT MGR is missing' error, and don't know what to do next. I chose 'Custom Installation' and selected the only hard drive that was visible when prompted. Computer will not restart with DVD or without DVD. What now? Windows 7-