In trying to access the ram chips for upgrade I am trying to get the cover off. It is an unusually large sheet of plastic with four screws. Yes, I have loosened the screws but in trying to pull off the cover it is bending to the point of almost breaking and I don't want to force it. It is the 15.4 size gemstone.
View 4 RepliesFor a few months now when I switch my Acer Aspire 5535 on for about 5 mins it sounds like the fan is rubbing against the bottom cover. It does go away when it warms up but its not very good when I have to use it on the train or in the library!
Is there anything i can do? Can i take the cover off and have a look without damaging anything? The laptop runs fine otherwise.
I have a 5920 that is just out of warranty and want to upgrade the 160 gig HD with a 500 gig WD. The 5920 is a wonderful machine and working fine. Looked like a five minute job to remove the ram/HD cover by removing the 7 screws visible on my rear cover. But, it wouldn't come off, felt like more screws were possibly under the MS Vista label on the cover. A web search resulted in a downloaded manual for the 5920 that said "remove 9 screws". No screws shown under the label. Looking around some more, I see 2 small "indents", for lack of a better word, that could hide the 2 missing screws. Were these 2 "indents" effectively "tamper-proof" plugs? Looking at this site, I see that others were removing 9 screws but it was also noted that the cover had to be "carefully" pried off after that. No mention of plugs. From a photo someone posted, it looks like the "indents" I see are at about the same location as 2 of the HD mounting screws. So, maybe ACER changed the design so that these two screws don't come off with the back cover anymore. Maybe the 2 "indents" I see are not "plugs" but simply undrilled holes so I only need to remove 7, not 9 screws and then do the prying. Questions: Does anyone know if these two "indents" are tamper-proof plugs or just undrilled holes? Then, I would like to know more about this "prying". What is being pried upon? A picture would be good. The back cover pictures I've seen here and in the repair manual do not show what must be pried upon.
View 6 Replies View RelatedI wanted to open my box to check the ease (or not) of a memory upgrade but had a helluva sweaty time trying to get the compartment cover off.
After undoing the 4 screws and getting it open a bit, it still seemed VERY firmly held in the vicinity of the fan vent area.
The plastic cover is pretty thin and I was terrified of breaking it, so tried a little prying, a bit of heaving, some levering, tugging, jabbing, swearing, praying etc. I even had the computer overturned and was looking for a way through the keyboard where I was convinced that a bolt must be holding the memory cover down.
Anyway it DID finally come loose but it was a bit scary, so I've made a couple of scans and added some notes on the lugs which were holding it in place in the hope that it might prove useful to others in the same predicament.
One scan is of the actual lid and the other is of what's inside, in case you get to feel like pushing a screwdriver in there - (don't).
I've found a source for the replacement part through EXTENSIVE research- and found an online user manual. I am not used to building/opening laptops, so I don't know whether
I'll need special tools to replace the broken back cover; are there any other parts I may need (such as hinges, antenna WiFi).
Is this even a job I should take on or is it pretty easy?
The LCD is fine- it's JUST the plastic cover I need to replace.
I picked up a 9600m GT on ebay and need help removing the bottom cover. The full bottom panel needs to be removed as it is trapping the copper pipes from the heatsink. Can anyone direct me to a guide on how this is done on a 7720g?
View 6 Replies View Relatedwhich would be fine... But there's nothing in the handbook about the right way to remove the back cover and i don't want to snap anything, however much vista needs 4GB of ram.
screws undone obviously but it still feels very firmly attached... what's the right way to take it off?
i wanted to install some new ram so i was takeing the cover off the back. when upside down, the top left screw was stuck and i tried to screw it off and now the screw hole is messed. also, when closeing the screw near the battery (bottom right) wont fully go in and i cant put it in fully?
View 5 Replies View Relatedanyone know of a keyboard cover they make for the studio xps 13? I find that I tend to wear down my keys (I already put a strip of tape over my space bar cuz that's where most of the wear is).
View 10 Replies View RelatedI'm trying to find a keyboard cover for my SR.
I found a few websites when I googled "sony sr keyboard cover".
Any reliable recommendations you guys can give me?
Any is there anything I need to worry about/look out for when purchasing one?
Or is it simply, "a cover is a cover"?
[url]
View 3 Replies View RelatedI just got my hands a Studio 15 with great specs at the cheap, but with a pretty badly scratched up LCD lid. Has anyone attempted replacing the lid? Is it hard? I've opened up and replaced a processor, keyboard, fingerprint reader, ram, and hard drive before, but never an LCD cover. I'm kinda worried about the power button and wifi catcher, and I'm worrying I may not put the screen back the right way. This is supposed to be for my cousin, but I can't give it this badly scratched up.
View 9 Replies View RelatedI mentioned previously that I didn't care for the smudges on the glossy black cover of the mini. So I ordered a spare LCD cover to save in case I want to revert back to stock, and took my mini apart tonight to paint the cover.
See the attachments.... one is a good example of the smudges.
right now I have the mini COMPLETELY apart!
I was going to paint the cover a red wrinkle finish, but have decided at the last minute to use a red rubberized coating instead. I guess this is similar to what the larger inspirons feel like.
Anyway, second coat is about to go on, I'll post pictures of it when it's done.
iv been looking around the and everyone says dell will only cover damage and not theft
this is quite worrying as i ordered a m6400 maxed out and its just to much to lose out on
anyone at all been able to light up the cover lights (just one of the colors even) for those who have done the 9400/E1705 to M1710 mods? I would really like to know how this can be done if there are some theories out there. Please refrain from saying how much you hate the lights or asking why I would care to do this :
Some methods I thought about trying:
USB port: 5V ok, will that work with the cover LEDs?
Fan port: I have heard this one might not work but can anyone confirm?
(I am talking about cutting off the connector that would originally go into the M1710 mobo and trying various things with the wires that happen to be color coded, 2 for each color of LED apparently.)
I have CR590 with Windows 7 installed. Recently have updated SFEP, Sony Shared Library, VAIO Event Service and VAIO Power Management to the latest versions from ftp://ftp.vaio-link.com.
Results:
1) "Capture" button started to work, it hadn't worked before, therefore all functional buttons work except AV Mode (I haven't installed Instant mode software)
2) VAIO profiles disappeared from PM settings — but this not a problem, I think I can leave with self configured profiles .....
I'm looking for a keyboard cover and I have an HP 6510B.
Do You know which is the right model for this notebook ?
Looking at focalpri** I've not found any model for my notebook.
what the screen/lcd cover that fits flush over the LCD is made of? Is it plastic or is it really glass like they advertise it is? I ask because people on youtube who are posting reviews say it's plastic and not glass. I'd like to know one way or the other before deciding to order.
View 3 Replies View Relatedive got a hp nw8440 that needs a switch cover,but talking to hp and spare parts warehouse they no longer make this item,.need cover and led board and led board cable
View 5 Replies View RelatedOne of the rubber grips on the palm rest of my Studio XPS 13 has fallen off, so Dell is sending a service technician to replace the entire palm rest assembly.
Does the warranty cover both replacement and service charges? Am I expected to pay anything?
I have a XPS M1530, And the screen doesn't go off when I close my laptop. I have contacted dell about it. They replaced the mobo, the LCD Screen, the Palm rest. And it still doesn't go off... I'm wonder what it can be...
Well I acquiered my Laptop last december and im noticing a few scratches, I googled for cases and covers but I didn't find anything amazing,
I've noticed people with macs that hace sweet looking covers but I haven't found any for my Dell, do you guys know any web page that sells them?
I just want to clear things up.
I have bought:
Coverplan Expiry Date : 24/06/11
Term : 3 YEARS
Now there is Manufacters Guarantee Expiry Date which is already expired.
I want to know what I'm insured from with the 3-YEAR plan.
And I'm expierencing some heat issues. I'm thinking of replacing the mobo, If I'm covered under it .....
About three months ago I returned my laptop to be repaired for a hard drive malfunction, not a big deal since I had the two year accidental protection plan. When I got it back they gave me a new hard drive, but my video card switcher no longer worked! Please see the attached image: the slide switch is towards "Stamina" however the "Speed" is illuminated. The slideswitch seems to be locked in place, I cannot move it.
I only recently had time to tell Sony about this, to which they replied that they cannot help me, since it has been more than 30 days since the repair. I replied explaining that I had this fancy-shmancy protection plan, and perhaps it could be fixed under that umbrella; to which they tactfully retorted that they had (prematurely) terminated my contract, and that if I want, I can send it in and be charged for parts and labor for the thing that they broke. [/rant]
Anyway..I would love to fix this myself, since I am in fact on my own. I took off the keyboard and palmrest, and was unable to find out how to remove the cover that contains the S-buttons/slideswitches/power button/speakers. Is it in there with just clips? This region looks particularly delicate, not that the rest isn't, however I feel as thought I should be especially gentle. Ive checked all the disassembly/teardown links I could find on the sz series, but none seem to detail how to remove this one part.
what dv7t models came with the vents on the bottom plastic cover.
I have
2X 7200RPM HD's
TV Tuner Card
Intel Pro Wireless w/Bluetooth
4gb OCZ RAM (2x2gb)
And my plastic cover only has a vent over the RAM. The computer is overheating, and I'm wondering if I have the wrong cover.
how to open the bottom cover of the dv5t. I removed all the screws i could find and could not get it to loosen up.
View 4 Replies View RelatedI just got my MBP 13, I'm wondering if there's a recommended cover/case I should get. Also, which keyboard cover?
View 9 Replies View Related1) Notebook Cover -> which is best? black or White?. Will the white get dull and stained over time?, Does the black look like cheapy plastic?. Does the black look like the ones on the black Inspirons because I think those do look nasty?
2) Built-In Broadband card (Wireless 5540 Mobile Broadband HSDPA Mini-Card ) -> how is the reception of these units compared to the USB dongle ones?. Is Access to where they are installed at the bottom of the notebook hence not voiding waranty if i decide to install at a later date? or Am I just better off getting one off ebay at a cheaper price?
I opted for the 4 year complete care package and was curious if it covers a battery or not.
I would get out my paperwork but it's currently buried in boxes. I could, but is there another area online I could check?
I already tried to see it on the website under my service tag, but it just says the amount of days left on the warranty and not the actual warranty itself.
I've scratched mine up a bit and wouldn't mind ordering a replacement, but I wanted to try successfully removing it first before contacting Dell. I've removed the three screws as outlined in the manual, but it won't budge. Is there a particular way of pushing it out, or maybe I need to be more forceful?
View 10 Replies View Related