I setup a beautiful new Dell E6500 for a client. However, it will not work AT ALL unless on AC.
OK, it IS a refurb from their outlet, but still, battery should work, yes?
Is there a setting in the BIOS or something that is different in this line?
Either my battery is dead or something in my laptop is wrong.
an Orange led is flashing in the right cornor of my laptop (not on the screen)
Its the battery charge led its flashing non-stop !
My laptop only runs when the power charger cable is connected this means my battery dont charge or is dead ?
After killing my old battery, my Latitude E6500 is refusing to detect the new battery I bought for it. It will run off the battery if I disconnect the AC, but will not charge, I have been using a co-worker's E6500 to recharge it.
I have been instructed to run the E6500 Bios flash, however since the computer does not detect the battery, it will not allow me to proceed with the flash. /forceit does not work. Are there any other command line variables I can use to make the bios upgrade perform without a battery check?
In all my years of building and using computers I have never actually experienced an actual case of the cmos battery running out. However, I think my awesome m1530 has shown me everything now. Here is the case:
Fresh windows 7 install - Windows 7 time is correct - Shut down - Boot up - The time is the exact time I shut down.
Is there anything this could be besides a dead cmos battery? I bought my LT brand new directly from Dell about 2-3 years ago, which is a ridiculously short life for a cmos battery. I have to dismantle my LT to bits in order to replace this battery. Anyway, having the wrong time makes a mess of windows, I really need some advice here.
Can it be something other than the cmos battery and what should I do?
so my 9cell battery is no longer taking a charge. my 6cell still charges so i know its the battery. i called tech support and they said that batts only have a 12mo warranty.
i bought a frickin 4yr warranty when i bought it is there any loop hole or something that i can use to get another 9cell for free??
This is 1.5 years old Studio 1535 machine (out of warranty). When I log in now (past 1 month or so),
I get a white dialog box saying thaa my battery is able to charge normally but its nearing its end of life.
However for past 1 week or so, I see that the battery shows 0% charge and says "Not charging" even though the AC adpater is plugged in.
Laptop works fine as long as AC power is on but the moment one removes it rightway goes to sleep .....
I have a Dell Inspiron 6400 which I bought in the UK new from Dell in April 2007.
The battery is a 9 Cell type (upgraded when bought).
Within the first year it got used on the battery most of the time.
After that it has been plugged in with battery (for backup incase of power outage) about 95% of the time.
Now the power only lasts a few minutes before it totally dies. It charges up to 100% and discharges normally down to roughly 85%. Then this is the strange part, it jumps all the way down to 6% charge .....
my dad gave me his old e6400 as his job paid him a brand new hp elitebook with all the bells and whistles, after checking my new toy, I found out that the battery if pretty much dead.
The bios reports that it's damaged and Ubuntu says it can only hold 25% of the original charge... And it only lasts 20 minutes .
I'm going to do a clean install of Vista soon but my battery is dead, won't even recharge, needs to be replaced.
Just wondering if I will run into any issues ?
Dell seem extortionate for an Inspiron 1520 replacement. Worth a 3rd party risk? Seen some non OEM ones on ebay with a 1 year guarantee for half the price.
I recently got a brand new 9-cell battery for my Aspire One, and it has been great until now. I left my laptop in sleep mode with about 60% charge remaining, and in the morning my laptop would not start. When I clicked the power button the orange light just flashed. So I took it home, left it on the charger all night (had a green light), and now it won't start again. I plugged it in, and Windows and BatteryBar are both showing 0% charge remaining. If I remove the AC plug it will stay on for a couple minutes then die again. Is my battery just completely dead?
View 5 Replies View RelatedI have a friend with an acer aspire 5920 and it is showing major symptons that the CMOS battery is dead.
View 7 Replies View RelatedThe battery is dead after 2.5 years. Charge it for a day, remove the power cord and the laptop won't start.
I don't know if I should go for a new battery or new cells?
Also, how do I open the battery the easiest way? I'd like to see if someone else have done it before I do, I guess there's a lot of glue in it that makes it difficult to open.
I have a Compaq nx9600 with a dead battery. I popped it open to find sony SF US18650GR batteries all lined up in a row within.
Further research finds 3.7V 2200mAh batteries out there from 6-8 dollars and I need 12 of them... Which means that it wouldnt be cost effective for me to fix the darn things.
I did find 3.7V 2400mAh for 99 cents each and was wondering if any of you might know whether I could use these batteries with a higher milliamp?
Is there any way to charge my battery now? I think my battery is completely dead now. Over the past few months, it's been staying turned on for less and less time without it's chord. Today, it said "battery 100%" "6 min". Usually, I have it charging just by turning the charger chord in some weird positions. I'm not sure if it's faulty wiring or not. I would much rather just buy a new battery than deal with faulty wiring.
Â
Yes, I have been getting the change your battery thing in the start up menu. I have an HP 625, and have had it for over 3 years now. In the past year, I've been having to adjust my wire just so it can charge. It jiggles around a little bit when inside, but the chord/plug itself doesn't seem loose or anything... Today, that didn't work at all. I've been trying for the past several hours to move my chord to the right position just so my laptop can turn on. I usually get it charging in no more than 1 minute, but today was different. Last year, I replaced my charging and it seemed to of made it much easier to charge. However, this is a fairly newish charger and it's my battery at fault this time.Â
Â
Will my issue be resolved just by getting a new battery? I can probably head over to Best Buy or something. Or maybe buy one online.Â
Â
If you think I may also have a problem with faulty wiring, what can I do to get it fixed? I feel like it would cost me a lot. Or, do you think will getting a new battery resolve my charging issue?
I am at my wits end with my e1705. I had a sudden meltdown about 2 weeks ago... screen went scrambled, BSOD,etc...
Performed diagnostic, memory on video card came back as bad. Replaced with new card (from Dell), reinstalled OS, completely reinstalled nVidea drivers from Dell (Used driver cleaner too)...
Everything went smooth for a couple hours after this was completed yesterday (full diagnostic showed no errors), but after booting up today, after about 5 or 10 minutes of use screen freezes and turns either solid cyan or black... a small pattern of thin lines appears also.
I was playing stalker a few days ago getting 50-70 FPS and now come today its so much lower at 20-30(not playable) and I tried CS:S, and COD4, and they all seen dramatic fall in FPS. I don't notice any artifacts but I just notice huge FPS hits. I also think my fan isn't running anymore but I am not sure. Does anyone one know what I should do now? Its out of warranty already.
View 10 Replies View RelatedGot a new E6500 last week, and I love it! I got the audio crackling to go away, though there are minor latency spikes every couple minutes,
that however don't affect the audio/video. The screen is wonderful, the keyboard, everything.
But one thing that bugs me is that when the fan starts going it will never stop. According to HWMonitor, my processor (P8800) can be at 29-30 deg C (right above ambient!) and the Nvidia card at 43 deg C and it won't stop! It's extremely annoying
I managed to buy a E6500 through a special promo at my university. Although I wanted an integrated graphic card (I'm not going to do *any* gaming so the nvidea cards are completely useless for me, right?), the promotion was limited to the nvidia 160.
Now what do I see upon receipt, they screwed up at dell: they delivered a notebook with the intel graphic card and no bluetooth. I've noticed them and they'll replace the notebook. Now I was thinking if I would be able to make a deal with Dell: send me the BT card that I'll install myself and some compensation for the missing graphic card (which I actually didn't want anyway).
Would I be able to pull off something like that, and what 'compensation' would you try to get (I already have max RAM, extra 6 cell battery, mouse, ...)
I'm planning on getting an E6500 with the 64GB SSD (performance option - I assume this is the Samsung SLC version).
It's my understanding that SSD's run a lot hotter ( since they are solid state chips) than a corresponding conventional HDD.
I would also think that they would consume less power than the conventional HDD, but what about the additional heat causing the fan to come on more often and/or at higher speeds? Would this negate the power savings?
Any comments would be appreciated. Also, FWIW I will be sticking with the Intel 4500MHD integrated graphics.
I recently purchased a Latitude E6500 with fingerprint reader. I was so impressed with the Studio15 that I had. Here is the problem the software with the E6500 doesn't let you login on websites or programs, like the Studio did.
When contacted Dell they stated that it will only work with Vista. My E6500
came preloaded with XP Pro. So I bit the bullet and downgraded to Vista.
Guess what still no use except to log into windows. Wave software SUCKS!
Does any one know of software that will work in XP with the Latitude?
Digitalpersona does not have a XP version yet. Yet on my Studio I converted to XP and it worked. Anyone have a link to the fingerprint software on the Studio?
I just play a few games here and there and I am seeing my system slow WAY down when even just doing light gaming. Is anyone else having these issues? I have the NVS 160 and the T9600 and even playing games like Command and Conquer Generals Zero hour which is a game that is several years old, I have to play it at 1024*768 with details turn down to min just to get the game not to spit and get jumpy. Its like it freezes every 2 seconds for a half sec or so..
I have speedfan monitoring temps for CPU and GPU and both are well within normal ranges, infact the fan is not even turning much past 4000 RPM and GPU getting no hotter then 64C at MAX..
Any ideas or experiences would be greatly appreciated. I just feel that the NVS 160 should be able to play a 3 year old game MUCH better then it is...
I have recenltly bought a e6500 everything was fine till I tried to install windows vista 32 bit again . The boardcom USH w/touch sensor was not installed in my former OS and I didn't have boardcom TMP neither .
But my fingerprint worked fine .
Then I reinstalled the windows and installed the latest drivers in order . I also updated the firmware but none of those helped me solve this problem .
When I try to enroll my finger print I get : "Device opened" and when I choose my thumb as an enrolling finger I get "an error occurred during enrollment please re-enroll"
Is there any thing that I can do ?
I took pictures of a refurb E6500 I got from the outlet (Regal Red) and my new E6500 (black).
They appear to have different heatsinks, with the new one having a larger one
I've been wavering back and forth between the T500 & E6500 for the past few weeks, but been pretty satisfied with our past Dell fleet and their service.
Up to Monday I was pretty much set on the E6500's, but I'm starting to see more and more threads about troublesome issues on the E-series. Things that would certainly bother me and my team.
Maybe we can keep track of all the issues and hopefully resolutions to them on this thread.
Here's what I've compiled so far:
Let me know what else to add.
1. Poor quality WXGA+ LED screens
Disappointed with LED LCD in E6400
E6400 vs. XPS M1330 LED Screens
2. Drifting Trackpad / Lack of proper sensitivity adjustments
E6500 TrackPoint drifting badly
3. Keyboard issues
E6500 TrackPoint drifting badly
4. DVD burner problems
Latitude E-Series DVD Burner troubles
5. Crackling/poor audio
e6500 crackling audio
6. Random lockups
http://www.dellcommunity.com/support...read.id=289406
I just got my dell Outlet e6500 today and I have a few questions/issues that you may be able to help me with:
1) when I opened it up, there's a small piece of plastic broken off the right side of the laptop (the piece is actually in the plastic bag that the laptop was in, so I assume it broke in shipping?).
If you look at the picture to which I've linked below from the review on this site (not actually my own picture),
it's the piece just to the immediate left of the wireless switch, along the bottom of the side, about 1 inch long (some kind of bay or card reader).....
I am in the process of ordering a new e6500. I have been reading through the forum for the last week and I came to the following configuration but would like to clarify a couple of questions.
Just an idea of what laptops I have, I am using Latitude D610, Latitude D620, Thinkpad T60. This might give you an idea of what I am used to. I find T60 is the best overall, D620 very mobile but slow, D610 ok and stable.
Here is what I am thinking for the e6500.
Latitude E6500 Intel® Core™ 2 Duo P8600 (2.40GHz, 3M L2 Cache, 1066MHz FSB)
Operating Systems Genuine Windows Vista Business Bonus-Windows XP Professional downgrade
Memory 4.0GB, DDR2-800 SDRAM, 2 DIMMS
Internal Keyboard Internal English Backlit Keyboard
Intel® Graphics Media Accelerator 4500MHD
250GB Hard Drive, 7200RPM with Free Fall Sensor
No Fingerprint Reader
15.4” UltraSharp™ Wide WXGA+ (1440x900) LED Display-Brushed Metal Black
Dell Wireless® 370 Bluetooth Module
Modem Internal 56K Modem
8X DVD+/-RW w/Roxio and Cyberlink Power DVD™
Camera / Microphone Integrated Webcam with digital microphone
Intel® WiFi Link 5300 802.11a/g/n Draft Mini Card
Intel vPro™ Technology’s advanced mgmt features are Off for future use
This machine will be used mainly for the Internet and not so demanding applications.
Now,
1) What do you think overall? Any issues to watch for?
2) Should I go for the WUXGA? I have been reading about the small font but was not sure. My T60 is set to 1280x800
3) I read about HDD noise, should I downgrade to 5400 or maybe upgrade to SSD?
I saw that the contrast ratio of the E6500 screen is something like 650 as is the Studio 15 's 1440x900 screen.
Is there a general consensus that these are superior to the 14.1" LED screens? I am led to believe that the T400 and E6400 are using the same Samsung/LG LED screens. I have seen the T400 and sent it right back b/c I got a Samsung screen that looked like milk. It was bad.
Is there a lottery to the Studio 15 and E6500 or will any LG or Samsung or AUO or Chi-Mei panel do? Are you guys pretty much happy with these screens? The notebook check or notebook journal numerical evaluation would put these screens on par with macbook pro, at half the price.
The E6500 I'm using has the P9500 (2.53 ghz, 6mb cache), Nvidia 160M, 2gb RAM, and 80gb 7200RPM HD. When I try to play a 1080P trailer from Apple's site, the thing doesn't seem like it can handle it. It's not smooth at all. I let it DL all the way too, so it's not a buffering issue or anything.
I was planning to use this on a 1920x1200 display, but if it can't even play the 1080p trailer properly...
Well I'm pretty much sold on either the e6400 or e6500 as a basic CAD electrical engineering laptop for college.
After reading a lot of reviews about weight, battery life, heat and screens. I wanted get some opinions.
I am for sure getting the quadro 160m for rendering and probably the p8600 since it's plenty fast and will consume less battery life and produce less heat.
I'm not sure whether to get the 14 or 15" model because of the size and heat and battery life.
I have a Lattitude E6500 with an intel 5300 (AGN) wireless card which has 'N' connectivity. I also have a netgear DG834N which is also draft 'N'.
Both should work on N out of the box, but for some reason I only ever seem to have 54mps connection from the connection manager popup bubble