I recently got a brand new 9-cell battery for my Aspire One, and it has been great until now. I left my laptop in sleep mode with about 60% charge remaining, and in the morning my laptop would not start. When I clicked the power button the orange light just flashed. So I took it home, left it on the charger all night (had a green light), and now it won't start again. I plugged it in, and Windows and BatteryBar are both showing 0% charge remaining. If I remove the AC plug it will stay on for a couple minutes then die again. Is my battery just completely dead?
Either my battery is dead or something in my laptop is wrong. an Orange led is flashing in the right cornor of my laptop (not on the screen)
Its the battery charge led its flashing non-stop ! My laptop only runs when the power charger cable is connected this means my battery dont charge or is dead ?
In all my years of building and using computers I have never actually experienced an actual case of the cmos battery running out. However, I think my awesome m1530 has shown me everything now. Here is the case:
Fresh windows 7 install - Windows 7 time is correct - Shut down - Boot up - The time is the exact time I shut down.
Is there anything this could be besides a dead cmos battery? I bought my LT brand new directly from Dell about 2-3 years ago, which is a ridiculously short life for a cmos battery. I have to dismantle my LT to bits in order to replace this battery. Anyway, having the wrong time makes a mess of windows, I really need some advice here.
Can it be something other than the cmos battery and what should I do?
The battery is dead after 2.5 years. Charge it for a day, remove the power cord and the laptop won't start.
I don't know if I should go for a new battery or new cells?
Also, how do I open the battery the easiest way? I'd like to see if someone else have done it before I do, I guess there's a lot of glue in it that makes it difficult to open.
I have a Compaq nx9600 with a dead battery. I popped it open to find sony SF US18650GR batteries all lined up in a row within.
Further research finds 3.7V 2200mAh batteries out there from 6-8 dollars and I need 12 of them... Which means that it wouldnt be cost effective for me to fix the darn things.
I did find 3.7V 2400mAh for 99 cents each and was wondering if any of you might know whether I could use these batteries with a higher milliamp?
so my 9cell battery is no longer taking a charge. my 6cell still charges so i know its the battery. i called tech support and they said that batts only have a 12mo warranty.
i bought a frickin 4yr warranty when i bought it is there any loop hole or something that i can use to get another 9cell for free??
I have a Dell Inspiron 6400 which I bought in the UK new from Dell in April 2007.
The battery is a 9 Cell type (upgraded when bought).
Within the first year it got used on the battery most of the time.
After that it has been plugged in with battery (for backup incase of power outage) about 95% of the time.
Now the power only lasts a few minutes before it totally dies. It charges up to 100% and discharges normally down to roughly 85%. Then this is the strange part, it jumps all the way down to 6% charge .....
my dad gave me his old e6400 as his job paid him a brand new hp elitebook with all the bells and whistles, after checking my new toy, I found out that the battery if pretty much dead.
The bios reports that it's damaged and Ubuntu says it can only hold 25% of the original charge... And it only lasts 20 minutes .
I'm going to do a clean install of Vista soon but my battery is dead, won't even recharge, needs to be replaced.
Just wondering if I will run into any issues ?
Dell seem extortionate for an Inspiron 1520 replacement. Worth a 3rd party risk? Seen some non OEM ones on ebay with a 1 year guarantee for half the price.
Is there any way to charge my battery now? I think my battery is completely dead now. Over the past few months, it's been staying turned on for less and less time without it's chord. Today, it said "battery 100%" "6 min". Usually, I have it charging just by turning the charger chord in some weird positions. I'm not sure if it's faulty wiring or not. I would much rather just buy a new battery than deal with faulty wiring.
Yes, I have been getting the change your battery thing in the start up menu. I have an HP 625, and have had it for over 3 years now. In the past year, I've been having to adjust my wire just so it can charge. It jiggles around a little bit when inside, but the chord/plug itself doesn't seem loose or anything... Today, that didn't work at all. I've been trying for the past several hours to move my chord to the right position just so my laptop can turn on. I usually get it charging in no more than 1 minute, but today was different. Last year, I replaced my charging and it seemed to of made it much easier to charge. However, this is a fairly newish charger and it's my battery at fault this time.
Will my issue be resolved just by getting a new battery? I can probably head over to Best Buy or something. Or maybe buy one online.
If you think I may also have a problem with faulty wiring, what can I do to get it fixed? I feel like it would cost me a lot. Or, do you think will getting a new battery resolve my charging issue?
I am at my wits end with my e1705. I had a sudden meltdown about 2 weeks ago... screen went scrambled, BSOD,etc...
Performed diagnostic, memory on video card came back as bad. Replaced with new card (from Dell), reinstalled OS, completely reinstalled nVidea drivers from Dell (Used driver cleaner too)...
Everything went smooth for a couple hours after this was completed yesterday (full diagnostic showed no errors), but after booting up today, after about 5 or 10 minutes of use screen freezes and turns either solid cyan or black... a small pattern of thin lines appears also.
I was playing stalker a few days ago getting 50-70 FPS and now come today its so much lower at 20-30(not playable) and I tried CS:S, and COD4, and they all seen dramatic fall in FPS. I don't notice any artifacts but I just notice huge FPS hits. I also think my fan isn't running anymore but I am not sure. Does anyone one know what I should do now? Its out of warranty already.
My Acer 5315 died during a power outage while updating the BIOS. I have been trying to revive it using an old post I found. I suspect everything is ok except for the autoexec.bat file that I have written. Any help? Or does anyone know where I can just get the Inside recovery disc?
I tried installing Service Pack 1 and it won't boot. Microsoft has just sent me a Vista Home Premium Repair CD that will hopefully fix it. I have Recovery Discs, but then I'll lose all my data. This is the 2nd time that my 5920G has broke like this, is there a huge design flaw with this laptop?
Is Acer always like this? It was such a high end laptop for its price (8600M GT, Core 2 Duo 1.5 Ghz, 2 GB RAM, HDMI, HD-DVD, for $1099), but I can never trust this company again.
so after about 6 months of not-so-abusive use of my notebook, the LCD screen sort of chickened out on me.. (Maybe me thinking to tear it apart sent it running lol)
What happened was, every so often before the day of failure, my screen would go gray in the bottom half and alright in the upper. Usually this would be fixed by applying very little torsion in the screen i.e. pushing on the left upper part of the screen and pulling on the right.
Not yesterday. When that happened and I made this move, it only became worse, lines started forming in the screen and then the screen went from white to black like paper burning..although moving it wouldn't make it stay that way. Now, I could only see about 1/3 of the upper part of the screen.
Now, I can't immediately claim the warranty of this thing, since it was my dad who bought it at Singapore, and the ITW says that the buyer must make a personal appearance with the necessary documents i.e. passport, reciepts etc. before the laptop could be repaired.
The first impression I got was perhaps the wire connecting the LCD to the mainboard needs to be reattached or something, but my local Acer service center suggests that it might as well be an LCD screen fault altogether.
Now, how would you know if it's your LCD screen and not just wires that went kaput? I was pretty convinced that it might just be the wire, since the method I used to do solved it, but now it doesn't budge...
My 1362 WLMI will not boot, it gives 1 long and 2 short beeps, the HDD runs as normal, and all the other LEDs light up, but it will not get past this, and there is nothing on the screen.
This follows an obvious failure to flash the latest BIOS... leaving me with a dead laptop..
My friend has mess up his Acer Aspire 5520G. And I'm supposed to help him fix it. His laptop has a nVidia 8400 graphics card.
When the laptop is powered it keeps rebooting itselve evry 3-4 seconds, and nothing is displayed on the screen. I don't know what's wrong with my friend's laptop but I think it might be related to the BIOS been correpted in his laptop. He tried to flash the BIOS from VISTA.
Anyways, I got Crisis recovery disk, and the latest BIOS for his laptop, and I got also a USB floppy drive. I removed the harddrive and the optical drive to force the laptop to boot from the USB floppy drive. I removed the battery too.
I pushed Fn+Esc, plugged the charger in the laptop and powered the laptop. The laptop know doesn't reboot itself but doesn't detect the floppy drive either.
I used the floppy to make a boot CD and tried to flash the bios again using the DVD drive this time. Pushed Fn+Esc again. The laptop turns ON and try to read the CD for about 5 seconds and then nothing else happens.
1- Is it a BAD BIOS.
2- How to make a boot CD to use with Crisis Recovery.
So after packing up my comp at a friends house my comp is kinda dead, it was alive before I left my home and everything was fine then.
When i try to start it the cpu is flickering for a bit then freezes so i dont se any bios or anything.
The blue tooth and the lights to the right of the key board are lit to and I have no idea what to do.
Ive tried my old ram mem sticks, pulling out the battery and trying without it, trying a new hard drive, checking for loose cables inside the comp, checking for dust and screaming at it but nothing works.
I talked to some friends and they suggested something called flashing the bios but I have no idea how to do it and I dont know if it will work since i cant se the bios start up screen before it freezes.
I have called acer but they basicly told me to send it in but i dont know if i have any varenty left on it so I rather try to get it working on my own before sending it in if I still got varenty on it.
I have the above model and it seems to be performing quite nicely. However, what I've noticed on all Valve games is that after a few minutes, the frame rates drop from mid 70s-80s (low) to 10-15 regardless of whatever resolution, texture or ingame setting I change post this sudden drop. restarting the game makes the problem temporarily dissapear but is back within a few minutes. The effect is especially noticeable when there are about 30 zombies on top of you
I've tried disabling one core, reducing sound to low and have even monitored temperatures via nvidias system checker as well as speed fan. At no point does GPU/ CPU temperature exceed 60 degree celcius. Have also tried several drivers all the way from 178.x to 182.x (using modified infs) to no avail. Please share your input regarding this problem.
I also accidentally uninstalled acer bioware protection and upon reinstalling cannot set it up since clicking a blinking finger on the setup menu states "Unable to select fingerprint device!"
Music sounds rather "tinny" and baseless using these inbuilt speakers. I assumed with all this dolby gee whizz, id get a sublime experience
I have an Acer 5100 and the touch pad has died ( including all the buttons ). Was perfect one day , turned it on the next day and it was dead. I'm surviving on an old IBM mouse plugged into USB port at present.
Have checked the mouse properties and it says it is working properly ( which it obviously isn't ) . Have uninstalled and re-installed including checking for latest driver on line . The mouse properties still tell me everything is working properly .
i have an acer travelmate 3262, it crashed a week ago, it loads windows (XP) normally, then when the word "welcome" appears, it gives me an error message about not being able to read, write, flush something related to the registry (i know i sound retarded but i really don't understand the message) then it keeps restarting, and checking all the drives for problems, then the error message, then restarts again !
i tried to use the safe mode but it freezes before opening it (and restars again)
i tried to reinstall windows, but it doesn't seem to recognize the bootable CDs!! it doesn't recognize the acer recovery CD either :S
i tried using the alt+F10 method to restore the C drive, but still, it doesn't recognize it either !
I have an Acer Aspire 6930G notebook, it approx 3 months old and was running without problem until last week when the Optiarc BD-Rom BC-5500S drive stopped loading/playing or recognising any discs in the drive whether DVD, CD or BD-Rom - all that happens is that the BD ROM drive makes a "B-Dum, B-Dum, B-Dum" noise at the regular rate of about once per second and after about 2 minutes of this timesout. If you right click on the Drive icon and select "Explore", then the drive tray ejects and the message screen "please insert a disc into drive F:" displays - when I insert a disc into the try and close then the all that happens is the noise as described about again. I do not hear a fast spinning sound at all, just the slow steady B-dum noise.
What I am trying to find out is whether the drive is broken and it is a hardware malfunction, or whether it could possibly be a driver problem or Windows Vista problem causing this, or even whether something simple like the 30-day trial of "Powerdirector" that was pre-installed but since elapsed, could have somehow caused the disc to stop working. I know nothing about filter drivers, but could this be something to look into?
Nothing loads at all - no audio Cd's no DVD's, no data discs, no blank discs. It seems strange that neither laser appears to be activating.
I bought the notebook over the internet from Amazon so am trying to find out if this is a hardware or software problem first, before contacting them, as if it is a software problem this would not be covered under the warranty.
I have an Acer laptop, 2 ys old or less, and the monitor went dead. The computer runs, but the monitor does not work. It has a nvidia card, and I have heard it might be the issue. Motherboard?
i got the New DC/USB power board today and installed it. Put everything back together and its still Dead. Could something else have been damaged. The old DC/USB board smelled burnt and it had a little smoke coming out by the board. Which led me to believe it had a short and burned up. Now I dont know what do do. Any suggestions to trouble shoot this? I allready got a now AC charger and battery so i know thats not it.
I have an Acer Aspire 5310 laptop which appears to have a dead bios and i'm hoping someone can help me bring it back to life.
Although I'm not a complete novice with computers i have always avoided messing with things like the bios etc... so i'm struggling a little on what some of you would consider basic steps.
The Laptop powers on, the fan spins for a few seconds and the hard disk light comes on..... I've followed several threads on different forums which have led me to believe that it is the bios.
If i remove the battery, press and hold the fn + Esc keys and then plug in the ac adapter, the power light flashes orange for a second. While continuing to hold fn + Esc, if i press the power button the fan spins constantly and slightly louder than before... but nothing else happens???
I've tried to follow steps to flash the bios using a usb stick and the bios versions 1.50 from the acer website but to no avail.
