My hard drive turned bad few days back and i now purchased a new WD3200BPVT 320 GB internal hard drive for my system. I installed it myself after reading all instructions and guidelines. But when i start it, system says, hard drive not found, try to reseat it. I have also reset it, but again same error coming. I dont know whats gone wrong with the hard drive or system..?
View 15 RepliesMy existing hard drive is failing. So I purchased and installed a new hard drive in my laptop. Ran diagnostics. Failed the hard drive "confidence test" and got error reading 4400:011A target not ready. I ran the "device self test" and it passed. The other possible tests "read test" and "verify test" are grayed out probably because the diagnostics/system cannot see the hard drive. At the dos prompt I can access C drive and run its DIR and CHKDSK. So the new drive appears to be physically installed but the computer system does not recognize or identify it.
View 2 Replies View Relatedinternal hard drive disk not found; no bootable devices; start up repair finds no solution..... I have reseated the hard drive several times. the computer runs extremely slow. Dell Data Safe had recommended replacing the hard drive ''couple of months" ago.
View 3 Replies View RelatedI have Inspiron 14R N4010. Its 2 years old. Its Toshiba hard drive(320 Gb) crashed 8 months before so I bought new WD hard drive(500 Gb), which also crashed again 2 weeks before(OS drive had bad sectors apperently) . Hence i got it replaced by WD for a new 500Gb hard drive.
Now, when I am trying to install OS in my new hard drive, i am getting following error:
Intel UNDI, PXE - 2.0 (build 083)
Copyright (C) 1997-2000 Intel Corporation
For Atheros PCIE Ethernet Controller v2.0.2.3(06/18/10)
Check cable connection!
PXE-M0F : Exiting Intel PXE ROM.
Operating System not found.
after learning about possible mistakes by reading some forums
1) I checked that hard drive is installed properly, all connections are good.
2) DVD I'm using to install Window 7 is bootable one & i have used it before
3) BIOS settings are checked to boot fromCD/DVD drive. (It is not booting from network adapter which supposed to be reason for ethernet error as per many other forums)
4) I tried draining current by pressing power button for 20 sec to reset settings.(I read in some forum) but even that didn't worked.
BIOS is detecting hard drive...so that is also not issue. Could new hard drive be damaged? should i get this new one also replaced again? I need some way to confirm this before me sending it back to WD.
In one microsoft forum, I read for same problem
"update the basic input/output system (BIOS) to the latest version by contacting the motherboard or computer manufacturer and check if it works.Important: Modifying BIOS/complementary metal oxide semiconductor (CMOS) settings incorrectly can cause serious problems that may prevent your computer from booting properly. Microsoft cannot guarantee that any problems resulting from the configuring of BIOS/CMOS settings can be solved. Modifications of the settings are at your own risk.
Ref : [URL] ....
Since modifying BIOS setting involves risk
I replaced the hard drive on my inspiron 1545 and tried to restore it with the dell data safe disks that I made when I got the machine. Windows 7 loaded but I couldn't do anything with it, It was very slow, I couldn't even get it to update. So I loaded in the windows 7 disk that came with it and now I have windows up and running and updated. My question is what drivers do I need to install. I went to dell/support and entered my service tag number and it came up with a list of drivers (46 of them), some I know I need but others seem to be for things I don't know if I have on the computer. How do I know which ones I need?
Also I read something about a file called Dell System Software but its not on the drivers list. Do I need it or not?
I have a Dell Inspiron 1545 running Windows 7 64 bit SP1. Recently I cloned my old original SATA hard drive for a larger Seagate (600Gb). All is fin apart from no windows update and an annoying request to activate. When i try to update I get a message that my service isn't running and I need to re-boot. It is running and a re-boot makes no difference. In System properties the laptop says it is activated but Windows thinks otherwise.
View 5 Replies View RelatedUnit powered up fine before, no issue's....worked like a champ until drive failure.
Had a hard drive error code, replaced w/ upgraded 500GB from 320GB. Computers are not my acumen although I found that I can take them apart and put them back together w/o issue-so far. Rebuilt my old Toshiba Satellite 455...new base, top, charger jack, screen, etc..works perfectly! It would be the drive which slides in on the left,, held by two screws, not the disk drive unit.
Powered up fine, than several minutes later powered off. Charger is fine, I replaced the charger jack, still won't power up.
I broke the WLAN white connector, pulled the male end off the board by accident., black OK. It broke when I went to replace the charger port. That wouldn't cause it to not power up though right?
I replaced the complete charger port board, not just the port. Seems something happened after I replaced the new driver card
The hd on my Inspiron 1545 has crashed and subsequently will not boot up. I have purchased a new hd and fitted it.
The recovery disks I have go through the local dell recovery routine but fail on the second disk. I only have the utilities cd from dell no other CDs.
I have windows 7. What I need to restart the laptop?
I replaced my WD 250GB RPM 5400 with a WD 500GB RPM 7200 and I get a "No boot sector on internal hard drive" "No bootable devices" I have both original disks ( Operating System Windows 7 and Applications.) I've checked the BIOS and it shows the new HDD. I put the Operating System CD in and started the computer than I hit F12 went to CD/DVD and hit enter I received the message "No boot sector on Internal hard drive" "No bootable devices"
View 3 Replies View RelatedI have got a inspirion 1545 and when i boot it up i get the message "no bootable device found please reseat the drive" ?????
View 5 Replies View RelatedI have a Dell Inspiron 1545. So, a few months ago, I got mad at my laptop and slammed the screen down. I think it was taking its sweet time shutting down or something. I can't remember. Anyway, the next time I tried to turn it on, it goes into Startup Repair, and then comes up with a screen of errors, namely "StartupRepairOffline", "Autofailover", "NoOSInstalled". I can go into advanced options and go into DOS command (it comes up to the X drive); I was able to successfully pull off stuff I wanted, but I'm thinking I damaged the hard drive. I've let this sit for awhile, using my daughters' laptop, but now I want mine back and want to repair it. What should I do first? Also, I don't think I have any startup disks or anything like that.
View 5 Replies View RelatedThat's was Dell's Diagnostic's (F12) tells me about my Studio 1745 - and no other errors are found. I'm assuming it's has a fried hard drive but how can I be sure before I buy a placement hard drive and install it?
View 3 Replies View RelatedInstalled replacement hard drive in Latitude E6510. Ordered same drive as originally installed from Dell. When I try to install OS on new drive I get the "No Boot Device Found" error. When I enter set up the HDD and DVD drive are shown as installed. I changed the boot sequence to have the DVD run as first boot device.
View 1 Replies View RelatedI have a HP Envy 4 - 1046tx Ultrabook and the operating system is Windows 8.1 64-bit. While downgrading to Windows 7 64 bit I was unable to find the hard drives. In the installation screen it showed me "No drives were found. Click Load Driver to provide a mass storage driver for installation.".
I downloaded all the versions (from latest to the oldest) of Intel Rapid Storage Technology drivers and tried installing them one by one but they didn't work and still the hard drives aren't visible. But if I use a Windows 8 installation disc and install the driver the hard drives are visible.
I need my computer to display the hard drives by default without requiring a SATA driver. How do I do that? My chipset manufacturer is Intel and the model is Ivy Bridge HM77.
I've got XP SP2 running just fine on my XPS M1530, but when I leave it powered up overnight now, in the morning I see this on the screen:
"Internal Hard Disk Drive not found. To resolve, reset the drive. No bootable devices found."
If I reboot from that screen it goes to the same message. If I power down and restart, it boots up just fine.
I'm new to having Dell computers. Today I received a Dell Inspiron 15z 5233 laptop with windows 8 on it. It has a 32 GB SSD and 500 GB hard drive. I can not see the SSD drive in the windows file explorer, nor do I see it in the Disk Management utility from the Control Panel. However, I do see it in the Device Manager as an SSD and another Hard Drive in the Disk Drive section. The SSD driver is up to date. I have not installed any drivers on the computer except for the Serial ATA CY1HK_WN_12.8.0.1016_A03. That was only after I tried to install windows 7 and it said "No Drive Found" when I tried to select a drive to install on.
I googled what could be the problem and saw that it could be a driver issue with the SATA connection. So I got that driver (Intel Rapid Storage Technology Driver) and the SK Hynix Solid State Drive Firmware update. These are the most current on Dells website. This is an older computer, says late 2012. It has an i5 Processor. The SSD is SSDPM830 mSATA in the device manager. Storage Controller: Intel Mobile Express Chipset RAID SATA controller. When I try to save a file, I do not see an SSD drive, there is only one drive, the C: drive which is the 500 GB disk drive. I hope I have supplied enough information to understand the problem.
So I put the drivers on a USB and tried to install windows 7 again, and it still shows No Drive Found, and when I tried to browse for the drivers, they do not appear on the USB. It will show all the folders on the USB, but I can not open the folder they are in. So I put them directly on the USB outside of any folders, and they still do not show up. Also, I changed it to Legacy mode, safe mode off for the boot settings.
I assumed I did not have to install any drivers on windows 8, because it detects everything automatically now days. Should I go ahead and install some drivers on windows 8?
got a inspiron 1545 recently with a SATA 320 gb HDD / 4gb ram with Windows Vista Home Basic. Like most of us I hate Vista. So I created a partition & installed XP.
Used a program "EasyBCD" to setup dual boot. I get the dual boot screen at startup. But only XP boots. After a little probing, came to know that there are only 2 options in the BIOS for SATA operations. AHCI & ATA. If I select ATA I can boot only to XP. If I select AHCI then I can boot only into Vista. Searched around but the solutions were a bit over my head. Really appreciate if anybody could come up with something in lay mans terms.
Using my inspiron 2330 (only 18mths old ) as normal next thing it tells me it encountered fault and has to reboot anyway it keeps saying scanning and repairing drive (c) then does not allow me to log in so i manage to get into bios to do a scan and it guves me a error code of 2000-0142 validation code of 112406 and and then says harddrive 0-s/n wd-wmc152946178
When i finally manage to log in my desk top screen is flashing and keeps telling my hard drive fault ....
My uncle has a Dell Inspiron 1545 with 3Gb RAM, 160 Gb HD and Windows Vista Home Premium. On boot up there is an error message stating that a back up should be performed immediately as the hard drive has a serious problem.
The good news is that I managed to make a clone of the 160 Gb HD to a 1000 Gb HD (Western Digital Blue) using Paragon software before the original drive failed. The bad news is that the cloning process stopped at 42%, but this 42% included the recovery partition and another part of the HD called Dell Utility.
I installed the cloned WD drive and pressed F8 on boot up, but the advanced boot menu did not appear. Instead I get the error message 'no bootable devices'.
I ran the diagnostics program using F5. All the tests were completed and 'passed'. The BIOS recognizes the new drive as 1000 Gb.
Question: how do I boot the laptop? My uncle does not have any recovery media.
My Recovery E: Folder is full -- 31.9MB free of 14.6GB - Windows Vista. I keep getting pop ups/messages saying that my E: folder is almost full, and occasionally that I should close my internet browser so I don't lose information.
Some of them discussions said to go into the E: folder and delete files which should be there (can't access it the folder -- there's only a warning message) or to change the Drive Letter (get a message that says it cannot remove "the letter drive of your volume", and now I'm not sure what I should do next.
Operating system not found" when starting computer. Aspire V5 with Windows 8. What can I do?
View 3 Replies View RelatedI have a problem in bootin my inspiron 14z. Everytime when I start the boot, it always stuck at Dell logo. Sometime, it said that internal hard disk drive not found to resoldve this issue, try to reseat the drive. The system was running well just until last night.
View 3 Replies View RelatedI've been looking everywhere for an answer to this question and can't find it. I have an Inspiron 9300 (old.. I know), and it still works great for everything I need it to do, except one thing. I have no storage space at all.
I've been looking at throwing in a new HD, preferably as large as possible.
The only problem is all the conflicting things I hear about these systems.
First off, I know that mine is an ATA model, not SATA. I'm definitely looking for storage space above all else. So whats the biggest drive this laptop will support? I've been looking at this one (Western Digital 250 GB 5400 RPM), but I've heard things about the bios only allowing hard drives up to a certain size.
I have a HP computer and I was wondering if it is possible to replace the Dell hard drive with the HP and save myself some money.
View 3 Replies View RelatedI'm using Dell Inpsiron 1526 with 160 GB HDD (5400 RPM I think). I want to upgrade it to higher capacity.
Can you tell me if Inspiron 1526 has extra bay for 2nd hdd. If yes, can I use the 160 GB HDD with the new HDD i buy(I'm thinking to buy Seagate Momentus 7200 320 GB).
If its possible to add 2nd hdd, what extra accessories will I need? I mean the caddy, cables, etc.
I have a Dell Inspiron 1501 Laptop, last week when switching on the laptop I was presented with an error saying "Disk Read Error", the laptop would not boot up at all not even in safe mode.
I ran Dell diagnostics and it gave me a error code of 0146 which is harddrive related. I then attempted to repair the windows installation using chkdsk /p and /r but this seems to have made things worse! When booting up, all i can see is a blank screen
What is the MAX Size hard drive my Dell 9400 can take ?
The 9400 went down during last night and came up on the screen with this.
** Hard Drive - DST short Test**
Test Result : Fail
Error Code 2000-01-42
Msg : Unit 0 : DST Log Contains Previous Error(s)
I replaced the hard drive in my Dell Inspiron N5110 laptop. I need to get the programs and data files transferred to the new drive. I have a Repair Win 7 - 64-bit CD, made from the old hard drive -- do I use that to boot up the computer? Or do I use the old hard drive image that I have stored on an external hard drive?
View 1 Replies View RelatedI ran the diagnostics tools and it failed to detect hard drive. I'm trying to use a usb OS but it fails to boot too. I tried tweaking the configs in the bios setup ( sata port, etc) , yet I cannot even use an external boot drive.
View 2 Replies View RelatedHow do I tell what type of hard drive I have in my Inspiron 1520? I am pretty sure it's IDE/ATA, but I am seeing info in my web research that says SATA. Not sure which to buy. Maybe this is a dumb question.
View 6 Replies View Related