Dell Inspiron 1545 :: Won't Power Up - Hard Drive Failure
Nov 5, 2014
Unit powered up fine before, no issue's....worked like a champ until drive failure.
Had a hard drive error code, replaced w/ upgraded 500GB from 320GB. Computers are not my acumen although I found that I can take them apart and put them back together w/o issue-so far. Rebuilt my old Toshiba Satellite 455...new base, top, charger jack, screen, etc..works perfectly! It would be the drive which slides in on the left,, held by two screws, not the disk drive unit.
Powered up fine, than several minutes later powered off. Charger is fine, I replaced the charger jack, still won't power up.
I broke the WLAN white connector, pulled the male end off the board by accident., black OK. It broke when I went to replace the charger port. That wouldn't cause it to not power up though right?
I replaced the complete charger port board, not just the port. Seems something happened after I replaced the new driver card
My existing hard drive is failing. So I purchased and installed a new hard drive in my laptop. Ran diagnostics. Failed the hard drive "confidence test" and got error reading 4400:011A target not ready. I ran the "device self test" and it passed. The other possible tests "read test" and "verify test" are grayed out probably because the diagnostics/system cannot see the hard drive. At the dos prompt I can access C drive and run its DIR and CHKDSK. So the new drive appears to be physically installed but the computer system does not recognize or identify it.
I have inspiron 5520 laptop, i ran a diagnostic test which shows Hard disc test failure. it also shows hard disc failure is imminent .
Also in dell support center - pc checkup I ran test Hard disc failled in two tests, Targeted read test and SMART short self test, my laptop is under warranty. what should i do?
I replaced the hard drive on my inspiron 1545 and tried to restore it with the dell data safe disks that I made when I got the machine. Windows 7 loaded but I couldn't do anything with it, It was very slow, I couldn't even get it to update. So I loaded in the windows 7 disk that came with it and now I have windows up and running and updated. My question is what drivers do I need to install. I went to dell/support and entered my service tag number and it came up with a list of drivers (46 of them), some I know I need but others seem to be for things I don't know if I have on the computer. How do I know which ones I need?
Also I read something about a file called Dell System Software but its not on the drivers list. Do I need it or not?
My hard drive turned bad few days back and i now purchased a new WD3200BPVT 320 GB internal hard drive for my system. I installed it myself after reading all instructions and guidelines. But when i start it, system says, hard drive not found, try to reseat it. I have also reset it, but again same error coming. I dont know whats gone wrong with the hard drive or system..?
I have a Dell Inspiron 1545 running Windows 7 64 bit SP1. Recently I cloned my old original SATA hard drive for a larger Seagate (600Gb). All is fin apart from no windows update and an annoying request to activate. When i try to update I get a message that my service isn't running and I need to re-boot. It is running and a re-boot makes no difference. In System properties the laptop says it is activated but Windows thinks otherwise.
I am using a dell inspiron 3520 which is two years old.
It was working properly till last month, i ran my dell support center application after a improper shut down and it failed to run Targeted Read Test and SMART Short Self Test.
After that i ran the diagnostics and it returned the same result
Error code :2000-0142
I found out many websites saying run chkdsk /r and when i did it it got my laptop worse. my laptop started hanging twice or thrice a day.
I have a Dell Inspiron N5110. The Warranty ran out in July of last year so for some reason I cannot email technical support directly.I ran the Dell PC Diagnostic test earlier today, all of which passed with the exception of the SMART Short Self Test which failed. Apparently my hard drive is "operating outside of normal parameters and should be replaced". I tried this twice, once with the Dell diagnostic software installed on my laptop and once using the downloadable diagnostics from the Dell website, both had the same outcome.
I then tried the system diagnostics accessed via the F12 key on system startup. Again all passed but the hard drive test which would not run and provided the following message:
Error code 2000-0142 validation 12985 Msg Hard Drive 0 s/n (omitted), self test unsuccessful status = 7
I have read around on the support forums that the next step to try is removing and replacing the hard drive then re-running the diagnostics. If this does not solve the issue and I have to replace the hard drive does that mean I will need to buy a new copy of windows to install on the hard drive, as my laptop came with no disks? I have backed up all my important files but obviously not any programs.
what my next steps would be and what the process is should I have to replace my hard drive? I am a "noob" in this area and don't want to spending uneccassary money on parts that don't need to be replaced or buying software I don't need to replace as it is already available if you see what I mean?
I replaced my WD 250GB RPM 5400 with a WD 500GB RPM 7200 and I get a "No boot sector on internal hard drive" "No bootable devices" I have both original disks ( Operating System Windows 7 and Applications.) I've checked the BIOS and it shows the new HDD. I put the Operating System CD in and started the computer than I hit F12 went to CD/DVD and hit enter I received the message "No boot sector on Internal hard drive" "No bootable devices"
I hate for this to be my first post, but after looking everywhere on the internet and on this site (I've been lurking a while) I'm still at the same place I started with my Studio 15 laptop. I'll try to include as much detail as possible.
I had my laptop plugged into my LCD tv via an HDMI cable as I often do, and when I went to close the laptop to use just the LCD, the tv flashed, showed a blue screen of death for a quick second and then went black. I opened the laptop and it was still on, but the screen wouldn't go on.
I restarted my computer and from there on out it kept making a beeping noise and stalling for a really long time at the "Dell Studio/progress bar" screen. After leaving it at that screen for a while the clicking stop and then it allowed me to access the Boot Options and Setup. Under setup, when I click on the drive under SATA hard drive, it shows something like 10GB and nothing more, and I have no options on the screen .....
My WD 320gb hard drive failed for the first time since I got it in January by registering the error 2000 0141.
I phoned dell after it wouldn't turn on again and I reseated the drive, took out battery, powered on to discharge static etc.,
he arranged for a replacement drive to be sent on monday. after that I tried again last night and now it works., typing from it now, and no noises or anything seems to be functioning fine!
So, what should i do now? install the new drive & all my software - real pain, but knowing new drive won't fail? did the error message mean my current drive is on the way out anyway?
We've got 2 D430's in house and they are awesome. One of them just had the hard drive stop working and it was confirmed by swapping drives between the two systems. These have a 2.5" proprietary connection and Dell is telling me that there is no way to access the drive to potentially recover the data since its not a standard PATA interface. It's got some really small ribbon connector on the drive that hooks into a custom connection to the D430.
Does anyone have any ideas, or familiarity with how we can get access to this drive so we can run some utilities on it? Dell seems to be of little help here and the D430 simply doesn't recognize the drive at all. I'm not sure I would have bought these systems knowing that this was a potential issue.
I'm hoping there is some know interface that will allow the drive to hook into a standard PATA connection to recover data.
I have an Envy 14-1110NR laptop and am getting a Hard Drive failure imminent message every time I boot up. Having run the HP diagnostics, the hard drive check fails so I'm guessing I have to replace it.
The hard drive is a Samsung HM640JJ which has gone obsolete.
I have an almost-new Z series, bought in the US (I am in the UK) in December.
It seems the hard drive has failed, as it started BSODing on boot. I tried to run the recovery partition and also Windows 7 recovery mode from a Windows 7 install disc, and these simply hung. Further attempts to fix it using Windows XP and Windows Vista media also failed with similar issues.
I was able to boot using NTFS4Dos, although it didn't seem to read my data partition very well, as files were missing.
Booting with Knoppix was more fruitful, as everything seemed to be there. I rewrote the MBR and didn't get anywhere, so then I deleted the three partitions (recovery, Windows reserved, and data partition) and started again.
Now Windows installs, but it BSODs after the first reboot.
I guess my hard drive has failed, somehow (there are no mysterious noises, and I don't recall any impacts, it's remotely possible my kids took a magnet to it, however).
I had hp pavilion 2230 tx laptop which is out of warranty. My laptop doesn't starting .It goes on Automatic Repair and after a minute it starts "Diagonising your PC" which remain for hours and at last "Automatic repair failed" message appears, below it restore option is also available. I proceed to restore but it also fails.Then I shutdown the laptop and open it again and I pressed esc button quickly and then I tried to test the hard drive which doesn't go furthur testing and display "hard drive test fails". Whether my hard disk is crashed or not.
I bought yesterday new notebook, HP ENVY 17-j162no. The very first time (and each time later) I started the laptop, I got an error of smart drive failure. I have never before on any computer experienced that even after such an error, nothing seems to be broken. I went to BIOS and ran the examining tool, and you can see below the results. What's the next step to do?
SystemDiags.log 2014-10-05 11:28:30 ================================================2014-10-05 11:28:30 EFI System Diagnostic 5.4.3.0 Started2014-10-05 11:28:30 Load Options =2014-10-05 11:28:30 Old Hii Protocol not found.2014-10-05 11:28:30 SysDiagsBiosData2011 Configuration Variable Acquired2014-10-05 11:28:30 Absolute Pointer Protocol Not Available
My HP G62-b23SA reports a imminent hard disk failure. Hard disk test reports SMART Error (301). Advised to back up the system and contact HP support to enquire if Hard disk needs to be replaced or just needs repair. I have since backed up the system, should it be replaced?
I have a Pavilion DV6-2140EI notebook with a failed hard drive. I purchased a new hard drive but to my surprise, all recovery disks or system image files are useless without the recovery partition on the drive. It appears that HP and Microsoft teamed up to not support hard drive failure. As you no longer get the original operating system on disk anymore, it looks like one is forced to purchase Windows again after hard drive failure.
I have had a Hard Drive failure apropos of nothing. Could not restart (HP Pavilion 15 230 sa ) would not boot and had a clicking sound. The ID is U0C40K-76U7AE-MFPV61-60UQ03 (some of the zeros may be 'o' s , hard to tell). Can I fix this myself?Lap top is 3 months old.
I have bought HP Pavilion dv6t-7000 CTO Entertainment Notebook PC on last year August. Yesterday while I was working on my Laptop It was restarted and Bios (setup) screen was shown. After this when I try to boot my laptop it shows blank (black) screen forever (no errors shown).
When I diagnose my laptop, I got Hard Drive Short DST Failure . I have called HP service center and they were telling to replace the hard drive.
But I have some many important files and documents in my laptop. is it possible to recover my files using some method?
Product description: HP Pavilion dv6t-7000 CTO Entertainment Notebook PC Product number: C0L24AAR
There's a "disk read error occured" when I startup and it won't boot into windows at all. I did a hard disk test in BIOS and the Short DST failed and the failure id is GTU23F-5QF788-XD6V5F-60UR0 for Hard Disk 1. I know there's an 80 SSD and 750 HD but which one failed?
If the ssd failed can I use the 750gb HD or does it need both?
If I do need to replace the SSD can I replace it with a regular HD (on a budget) and what size drive do I need? 2.5?
I have a Dell Inspiron 1545 that will not power on. After ordering a new power cord and battery, still nothing.I went on line and found videos on how to disassemble the laptop to check the power port. I found that mine was broken.I ordered a new one and following the instructions I replaced it. Still nothing when I press the power button. No lights on the computer at all.
i have one dell inspiron 910 laptop. I broke it connecting a wrong power adapter and now a need a small piece that is inside ; i think its a MOSFET transitor, and there are two of them in the motherboard (only one is break). In the surface I can read : 4835d X860 . I am searching since some days ago and i can´t find this piece or similar to replace.
This is a late 2008 build Dell Inspiron 1545, sold retail in December 2010.
Pentium dual core T4500, 2.3 GHz
Has been in irregular use as a spare machine, mains adapter only, battery removed. My house was struck by lightning over a year ago and adapter damaged. Replaced adapter and no further issue until now.
Laptop would not power up, no light. Tested adapter and tried another 2 adapters - still no power up. Replaced original adapter and plugged in depleted battery - powered up but had to press F1. Powered up with no issue with good battery. Once powered up the laptop seems to be charging battery OK. Guessed this was a power board issue but no change when replacement fitted.
My son has a Dell Inspiron 1545 ... The problem with its is, that it receives power into the unit but nothing is displayed onto the screen and therefore, nothing shows or happens. I know that the unit is receiving power due to the fact that I can open the Disk Drive. I have attempted the flea start without any success.
