My HP G62-b23SA reports a imminent hard disk failure. Hard disk test reports SMART Error (301). Advised to back up the system and contact HP support to enquire if Hard disk needs to be replaced or just needs repair. I have since backed up the system, should it be replaced?
View 5 RepliesI have an Envy 14-1110NR laptop and am getting a Hard Drive failure imminent message every time I boot up. Having run the HP diagnostics, the hard drive check fails so I'm guessing I have to replace it.
The hard drive is a Samsung HM640JJ which has gone obsolete.
I have a Dell Inspiron N5110. The Warranty ran out in July of last year so for some reason I cannot email technical support directly.I ran the Dell PC Diagnostic test earlier today, all of which passed with the exception of the SMART Short Self Test which failed. Apparently my hard drive is "operating outside of normal parameters and should be replaced". I tried this twice, once with the Dell diagnostic software installed on my laptop and once using the downloadable diagnostics from the Dell website, both had the same outcome.
I then tried the system diagnostics accessed via the F12 key on system startup. Again all passed but the hard drive test which would not run and provided the following message:
Error code 2000-0142
validation 12985
Msg Hard Drive 0 s/n (omitted), self test unsuccessful status = 7
I have read around on the support forums that the next step to try is removing and replacing the hard drive then re-running the diagnostics. If this does not solve the issue and I have to replace the hard drive does that mean I will need to buy a new copy of windows to install on the hard drive, as my laptop came with no disks? I have backed up all my important files but obviously not any programs.
what my next steps would be and what the process is should I have to replace my hard drive? I am a "noob" in this area and don't want to spending uneccassary money on parts that don't need to be replaced or buying software I don't need to replace as it is already available if you see what I mean?
Old hard drive made strange noises and stop working replaced using the same Toshiba part number,
Now when turned on says on screen the smart hard disc check has detected an imminent failure run hard disc test.
Memory test OK hard drive test smart check - not available short DST- warning.
System info hp Pavilion g6-2285sa, Product No D1Q30EA#ABU
O/S windows 8 64bit have no recovery disc.
msg hard drive
0-S/N WXN1E53EN501
Short self test unsuccessful
Tried other diagnosis, no joy
There's a "disk read error occured" when I startup and it won't boot into windows at all. I did a hard disk test in BIOS and the Short DST failed and the failure id is GTU23F-5QF788-XD6V5F-60UR0 for Hard Disk 1. I know there's an 80 SSD and 750 HD but which one failed?
If the ssd failed can I use the 750gb HD or does it need both?
If I do need to replace the SSD can I replace it with a regular HD (on a budget) and what size drive do I need? 2.5?
I have the Dell XPS L501x and am now getting a failed message when the SMART Short Self Test is run. The message says:
"Your drive indicates that a failure may be imminent. Backup all important files and replace drive."
The hard drive is SAMSUNG HM640JJ.
A couple of questiions please:
1. I take if that this is a legitimate error message as opposed to some system glitch.
2. If I buy another SAMSUNG HM640JJ drive how can transfer the data from the old to the new.
I hate for this to be my first post, but after looking everywhere on the internet and on this site (I've been lurking a while) I'm still at the same place I started with my Studio 15 laptop. I'll try to include as much detail as possible.
I had my laptop plugged into my LCD tv via an HDMI cable as I often do, and when I went to close the laptop to use just the LCD, the tv flashed, showed a blue screen of death for a quick second and then went black. I opened the laptop and it was still on, but the screen wouldn't go on.
I restarted my computer and from there on out it kept making a beeping noise and stalling for a really long time at the "Dell Studio/progress bar" screen. After leaving it at that screen for a while the clicking stop and then it allowed me to access the Boot Options and Setup. Under setup, when I click on the drive under SATA hard drive, it shows something like 10GB and nothing more, and I have no options on the screen .....
My WD 320gb hard drive failed for the first time since I got it in January by registering the error 2000 0141.
I phoned dell after it wouldn't turn on again and I reseated the drive, took out battery, powered on to discharge static etc.,
he arranged for a replacement drive to be sent on monday. after that I tried again last night and now it works., typing from it now, and no noises or anything seems to be functioning fine!
So, what should i do now?
install the new drive & all my software - real pain, but knowing new drive won't fail? did the error message mean my current drive is on the way out anyway?
We've got 2 D430's in house and they are awesome. One of them just had the hard drive stop working and it was confirmed by swapping drives between the two systems. These have a 2.5" proprietary connection and Dell is telling me that there is no way to access the drive to potentially recover the data since its not a standard PATA interface. It's got some really small ribbon connector on the drive that hooks into a custom connection to the D430.
Does anyone have any ideas, or familiarity with how we can get access to this drive so we can run some utilities on it? Dell seems to be of little help here and the D430 simply doesn't recognize the drive at all. I'm not sure I would have bought these systems knowing that this was a potential issue.
I'm hoping there is some know interface that will allow the drive to hook into a standard PATA connection to recover data.
I have an almost-new Z series, bought in the US (I am in the UK) in December.
It seems the hard drive has failed, as it started BSODing on boot. I tried to run the recovery partition and also Windows 7 recovery mode from a Windows 7 install disc, and these simply hung. Further attempts to fix it using Windows XP and Windows Vista media also failed with similar issues.
I was able to boot using NTFS4Dos, although it didn't seem to read my data partition very well, as files were missing.
Booting with Knoppix was more fruitful, as everything seemed to be there. I rewrote the MBR and didn't get anywhere, so then I deleted the three partitions (recovery, Windows reserved, and data partition) and started again.
Now Windows installs, but it BSODs after the first reboot.
I guess my hard drive has failed, somehow (there are no mysterious noises, and I don't recall any impacts, it's remotely possible my kids took a magnet to it, however).
I had hp pavilion 2230 tx laptop which is out of warranty. My laptop doesn't starting .It goes on Automatic Repair and after a minute it starts "Diagonising your PC" which remain for hours and at last "Automatic repair failed" message appears, below it restore option is also available. I proceed to restore but it also fails.Then I shutdown the laptop and open it again and I pressed esc button quickly and then I tried to test the hard drive which doesn't go furthur testing and display "hard drive test fails". Whether my hard disk is crashed or not.
View 9 Replies View RelatedI have a HP Pavilion dv7 Laptop not booting. I ran memory test, checked OK. Ran hard drive test message said smart check passed but long DST failed.
Failure ID : GLP5BR-66R7AO-QFPKOJ-61FSO3
Hard Drive 1.
I bought yesterday new notebook, HP ENVY 17-j162no. The very first time (and each time later) I started the laptop, I got an error of smart drive failure. I have never before on any computer experienced that even after such an error, nothing seems to be broken. I went to BIOS and ran the examining tool, and you can see below the results. What's the next step to do?
SystemDiags.log
2014-10-05 11:28:30 ================================================2014-10-05 11:28:30
EFI System Diagnostic 5.4.3.0 Started2014-10-05 11:28:30 Load Options =2014-10-05 11:28:30
Old Hii Protocol not found.2014-10-05 11:28:30 SysDiagsBiosData2011
Configuration Variable Acquired2014-10-05 11:28:30 Absolute Pointer Protocol Not Available
[Code] .....
Laptop will not boot up. Can not back- up either. (Samsung model ST1000LM024)
View 1 Replies View RelatedI have inspiron 5520 laptop, i ran a diagnostic test which shows Hard disc test failure. it also shows hard disc failure is imminent .
Also in dell support center - pc checkup I ran test Hard disc failled in two tests, Targeted read test and SMART short self test, my laptop is under warranty. what should i do?
Unit powered up fine before, no issue's....worked like a champ until drive failure.
Had a hard drive error code, replaced w/ upgraded 500GB from 320GB. Computers are not my acumen although I found that I can take them apart and put them back together w/o issue-so far. Rebuilt my old Toshiba Satellite 455...new base, top, charger jack, screen, etc..works perfectly! It would be the drive which slides in on the left,, held by two screws, not the disk drive unit.
Powered up fine, than several minutes later powered off. Charger is fine, I replaced the charger jack, still won't power up.
I broke the WLAN white connector, pulled the male end off the board by accident., black OK. It broke when I went to replace the charger port. That wouldn't cause it to not power up though right?
I replaced the complete charger port board, not just the port. Seems something happened after I replaced the new driver card
I have a Pavilion DV6-2140EI notebook with a failed hard drive. I purchased a new hard drive but to my surprise, all recovery disks or system image files are useless without the recovery partition on the drive. It appears that HP and Microsoft teamed up to not support hard drive failure. As you no longer get the original operating system on disk anymore, it looks like one is forced to purchase Windows again after hard drive failure.
View 2 Replies View RelatedI am using a dell inspiron 3520 which is two years old.
It was working properly till last month, i ran my dell support center application after a improper shut down and it failed to run Targeted Read Test and SMART Short Self Test.
After that i ran the diagnostics and it returned the same result
Error code :2000-0142
I found out many websites saying run chkdsk /r and when i did it it got my laptop worse. my laptop started hanging twice or thrice a day.
I have had a Hard Drive failure apropos of nothing. Could not restart (HP Pavilion 15 230 sa ) would not boot and had a clicking sound. The ID is U0C40K-76U7AE-MFPV61-60UQ03 (some of the zeros may be 'o' s , hard to tell). Can I fix this myself?Lap top is 3 months old.
View 9 Replies View RelatedI have bought HP Pavilion dv6t-7000 CTO Entertainment Notebook PC on last year August. Yesterday while I was working on my Laptop It was restarted and Bios (setup) screen was shown. After this when I try to boot my laptop it shows blank (black) screen forever (no errors shown).
When I diagnose my laptop, I got Hard Drive Short DST Failure . I have called HP service center and they were telling to replace the hard drive.
But I have some many important files and documents in my laptop. is it possible to recover my files using some method?
Product description: HP Pavilion dv6t-7000 CTO Entertainment Notebook PC Product number: C0L24AAR
I recently ran a test on my laptop(N4050).It first showed me I had a SMART extended self test failure. Then I had a hardware failure message. I have attached one of the things.May I know what am I supposed to do? My warranty has expired.
View 6 Replies View RelatedMy drive is working properly at the moment but has this error (video here) and it seems critical.
I have already backed up important files.
The model is Inspiron N5110 R15 and it's the stock hard drive.
using my unmodded 9300 and shut down for the night. This morning, when I tried to reboot, the process would get to the Windows splash screen, then flash a blue screen so fast I couldn't read it, then go to a black screen that gave me 5 options to start windows. No matter which one I pick, the same process happens again.
I videotaped the blue screen and it reads: a problem has been detected and windows has shut down to prevent damage to my computer unmountable_boot_volume and then it gives me unhelpful advice on how to fix the problem.
I ran the Pre boot system assessment and all items passed. Then I ran the Dell Diagnostic Utility for "unable to boot O/S" with the following results: HD Read Test error: 00F0:0244 and HD Verify Test error: 00F0:1A44. Both of these were on sectors in the middle of the volume and I canceled both tests after about 10 errors. All other memory, graphics, and HD tests passed.
I tried booting from the XP CD and repairing from the CD with no change. I ran chkdsk /p and it found one or more errors on the volume.
bootcfg /list gives me: there are currently no boot entries available to display.
What are my best options on trying to recover this without losing data? I have a fairly recent backup, but would like to try to save what's on the HD. Parallel install? What is fixboot used for?
Dell lists my drive as: M7601 Hard Drive, 60GB, 9.5MM, 7.2K Hitachi, Ibm Moraga
What is the drive of choice to replace this if I need to?
it is giving me fixed hard drive park error 0200:
I opened it up, looked at the IDE connectors very closely and they are good, tried 4 drives so far, run LIVE Linux fine as long as there is no hard drive in, the thing is, It does shows the drives in BIOS thou, and using F12 boot menu, hard drive is in the option.
I have a disk error on my XPS15Z. I ran a diagnostic and got:
Error code 2000-0142
Validation 534
Msg: Hard Drive 0 - S/N WD-WX11EC1F3775, self test unsuccessful. Status = 79
Do I have to replace my hard drive and if so, can I send it to get replaced? I am still under warranty.
Ok I have a Dell 3521 Laptop and the hard drive went bad. So I have replaced the hard drive and did diagnostics on it and everything went fine. So I put in my burned copy of the back up and it started running. It got half way through then gave me a hard drive error. So now I am stuck what is going on with this. I just want to get my laptop back up and running.
View 2 Replies View RelatedJust installed a new har drive into my Compaq CQ57. Ordered the recovery disks from HP. Put the first disk in disk drive as instructed and turned power back on. Now I'm getting a "No bootable device - insert boot disk" message. I thought that was what I had gotten from HP? how to recover system and then reinstall Windows 7?
View 1 Replies View Relatedi am using an inspiron n5110. (western digital)
i am getting an hard disk error code while running diagnostics: 2000-0151 validation: 18339 incorrect status = 3E.
when i inserted the hard disk in PC it somehow managed to boot with the os(w8) in the hard drive.
Any how the hard disk response rate is little slow. but in my laptop it stops with BIOS and doesn't proceed further.
Is it a hard drive error or some problem in mother board.
I got a hp Pavilion g6-2005sd laptop and I have some freezing issues. My laptop is lately randomly shocking. The screen is freezing and continues normally. But if I run multiple tabs browsing the net it is more frequently. I have run some tests with hp of hardware diagnostics and hard drive errors. But I don't know how to fix it. I got the error : [URL] .....
View 7 Replies View Related