When i turn on the laptop, display doesn't turn on even when external monitor connected via VGA/HDMI.. I hear CPU Fan sound, keyboard lights on, power light on.
View 1 RepliesMy laptop was working correctly and then I booted up one day, the bios worked fine but then the screen went black. I connected an external monitor to the lap-top and the laptop display works fine. As soon as I remove the external monitor, again, I get a black screen on my lap-top.
I have run the full system option of the Dell diagnostics and have 2 errors, battery and dvd flash rom. I have ordered a new battery. I have also noticed that my lap-top does appear to get quite hot.
I have connected my monitor to an external monitor. It works fine. Only problem I have ( and a little irritating one) is that the external monitor picks up display only after Windows is loaded. Pre-OS screens like BIOS settings, GRUB loader (I have Installed Linux ) doesn't show up)
Is this an issue with BIOS? Because, when I connect HP dv6000 to my monitor, I can see the BIOS screen as well. I am sure the problem is not with the monitor.
The BIOS is responsible for detecting displays before the OS is loaded right? I checked BIOS settings and there is nothing to indicate the display ports/devices (however, this page on HP website shows a BIOS screen "Advanced" which apparently has those settings)
I purchased a Dell XPS L502X laptop about 2.5 years. It crashes when you connect an external monitor, not immediately, but normally about an hour or two while connected. Its not a blue screen crash, everything freezes and the external monitor displays multicolored patterns. In the end I have to do a hard reset.
I have tested different monitors and HDMI cables and found no changes. Luckily the laptop is still under warranty and has Dell technical support has:
-run all possible diagnostics
-updated all drivers
-replaced the hard-drive (after formatting the previous hard-drive)
-Got me to test individual RAM units one by one
-Replaced the motherboard (twice)
At the moment, I am still dealing with Dell tech support and after the most recent motherboard replacement they are asking me to test it with different monitors using different cables. Although this is the next step, I'm skeptical it will make a difference, firstly as I have done this already with no difference and secondly because I am currently using the monitor and HDMI cable on a much older Dell Inspiron 1525 and its working 100% fine. If it continues to crash after this step they want me to once again format the hard-drive, re-install everything and test it again.
I am just after some Inspiron 15r has developed a fault with white screen. I have tried connecting it to an external monitor through the vga and the hdmi port but still get the same fault.
View 5 Replies View Relatedi dissasembled my presario cq60 and when i put it together the monitor won't activate.
i tried using an external monitor and the monitor refused to turn on from standby, a safety feature of the monitor. the small card in the underneath with 2 wires leading 2 the monitor, (i assume that is the laptop version of a graphics card) is fine, inserted properly, and i had a slight issue with the plugs fitting, but that was soon resolved.
I have Thinkpad Edge E330 bought this July, with win8 downgraded to win7. It recently started a problem where the laptop's own display doesn't display anything (just blank) if I don't have external display connected. The external display doesn't have be in use, just connected, and E330's own display works fine. If I disconnect the external display, the E330's own display goes blank also. It doesn't matter what display setting I have.Currently I'm not able to use my E330 as a laptop at all.
View 2 Replies View RelatedI am considering a 24" monitor which I need t share as a second on my 1710, as well as the primary on my gaming rig (2X8800GTX SLI).
I want to drive it @ 1920*1200. I don�t want to use the VGA connector for one of the machines, when I do resolution drops to a max of around 1600*1100. So, I am looking at some of the monitors that have DVI and HDMI connectors. The thought was to connect one of the machines via HDMI with a special cable like one from bluejean cable, and use the other straight through, and choose a monitor with an easy one touch toggle between the two.
I read some horror stories that the HDMI link via a DVI-HDMI cable isn't optimal, and someitmes has its own resolution or sync limits. Does anyone know about this?
My other choice is a cheapo DVI switch, but it would be cool just to hit the input button.
I've got a european Sony Vaio Z (first generation), which seems to have some major overheating issues, especially when it's connected to an external display.
Setup:
Sony Vaio Z11VN -> Docking station -> NEC2690WUXi (running at 1920x1200)
Here's a summary of temperatures when this machine is in SPEED mode (Nvidia 9300gs) in Windows XP (idle)
GPU: 92C(198F)
HD0: 41C(106F)
Temp1: 66C(151F)
Core0: 78C(172F)
Core1: 78C(172F)
Clearly, the temperature drops if I switch to STAMINA mode, or if I unplug the laptop from the docking station, however, in the latter case the temperature drops to perhaps 70C.. so that is without running it on the external 1920x1200 display.
and when running 3d applications or games, the laptop can simply shut itself off for no reason whatsoever (overheated?)
I've heard about overheating problems of the NVIDIA GPUs.. is this such a case? (NVIDIA 9300GS)
I'd like to know if anyone else have had this problem with their Vaio Z (i've seen ppl having problems with the FZ)
My model is a VGN-Z11VN (swedish, although distributed via the UK)
Whenever I connect AC adapter, display on my laptop goes black and it remians black even after I remove adapter. If I poweroff laptop while adapter connected and power on it again, the lights on keyborad just blinks and it shuts down. If I remove adapter and turn it on then it works fine.If I connect adapter while laptop is powered off then it charges the battery as usual .
View 3 Replies View RelatedI bought this computer which is running 7win64 to update my T60 which I use with my home TV, a samsung digital running at 1360x768 resolution. The computer's native resolution is 1920x1080. I bought an hdmi adapter for the displayport from lenovo when I ordered the computer. Initially, the display works and at first it ran long enough to get everything set for a nice crisp display that fits the screen perfectly. The sound is there too, and is passed on to my receiver by the TV. Very nice. But then it begins to blink off until it doesn't work at all (the sound is cut off too). Lately it won't stay on long enough to review settings.
All updates are in place, both from microsoft and from lenovo. This has Intel 4600 graphics built in, and intel has graphics drivers available, but won't install them because of the lenovo supplied drivers.
I can't get any support from lenovo support because another device is involved.
I read online of some early users who had this problem with a docking station and i guess the problem was resolved with an updated driver.
well I have a l702p 3d, I connect it to my samsung smarTV and it works wonderfuly (hdmi ofcourse), but I have a FLATRON W2243T LG monitor (it only has DVI and VGA ports) I try to connect it using hdmi-dvi adapters but the laptop does not recognize the monitor!
View 3 Replies View RelatedIs it possible to add a second 24" monitor for use with my laptop, which is connected through a workstation. If so, what is required?
View 1 Replies View RelatedI am having problems connecting an external monitor, Dell 2709W, to my Elitebook 820 G1.
I have an Intel HD 4400 graphics solution. The monitor says:
Out of range signal
Cannot display this video mode
change computer display input to 1920 x 1200 @ 60Hz.
I use a Display Port cable for the connection.
My OS is Win 8.1 64bit
I have used the HP support assistant to update all hardware drivers...
The monitor on my HP Pavilion dv9830us laptop has not been working for some time and I have had to use an external CRT monitor for my display. A couple nights ago, my operating system (Ubuntu Linux 10.04) failed to load and because I can't get video feed to my external monitor until the video drivers on Ubuntu loads, I am unable to run Ubuntu's repair feature and the beginning of boot.
Is there a way I can get my laptop to use my external monitor at all times, even at the BIOS screen? Is there a setting in BIOS for this?
I have just switched to Windows 7 Pro and it is already driving me crazy. I use a Lenovo X200 with my Ultrabase. I connect the notebook to an external display via DisplayPort. The Intel GM45 Graphics Driver crashes about twice a minute when the Notebook is docked and connected to the external screen. Than all screens become black and afterwards a message pops up, that says "Intel Graphics Accelerator for XP (R) stopped responding and has recovered". Sometimes the notebook crashes and reboots. That gets really annoying and I haven't found a solution. Bios Version is 3.20. I loaded the latest Intel Graphics Driver from the Lenovo Webpage (8.15.10.2302) with Windows 7 SP1 (all updates installed). When I use a standard windows driver and not the Intel driver the external display flickers black every minute once. The newest Intel driver (from the Intel Website) does not work, since it says that it is not released for my notebook.
View 6 Replies View RelatedI am using Dell Vostro 1015 laptop, Windows 7 32 bit OS.I am having problem with external monitor connection. When I connect external monitor to my laptop, it detects external display but doesn't show anything on external monitor and laptop screen also turns black. There is no problem with external monitor but with laptop hardware or something. I tried to connect many external monitors but in vane.
View 2 Replies View RelatedWhen I connect my external monitor (ASUS PA248) to my W520, the audio disappears. When I disconnect it, the audio returns. This seems a bizarre link between audio and video, but there it is. Note that the PA248 does NOT have built-in speakers.
View 3 Replies View RelatedI don't wan turn on both laptop screen and my external monitor at the same time. So is there any way to make my laptop screen auto turn off as soon as I plug my external monitor vga cable to my laptop (without pressing Fn + F2 Keys) ??
View 2 Replies View RelatedI got the "ATI display driver has stopped responding and has recovered from an error" several times over the last couple of days where my screen would freeze for a couple of second and then start working again and would display that message. I thought little of it as it did always seem to work afterwards.
Last night however it got extremely frequent happening at least once a minute and i decided to try and restart my computer to see if that would work. Now when I try to turn the computer on the screen stays black and will not do anything. I can hear that the computer trying to work as the fans are going and the power light is on, it's just the screen that isn't working.
[URL] ...
I found these guides on how to fix the error message but at the moment both are no good as I can't even use my computer to fix the problem as the screen won't work.
I am pretty sure the reason my computer is doing this is because of outdated drivers as I recently did a fresh install of windows and only installed the drivers that came on the CD I was given with my computer. I should have downloaded the latest drivers online.
I am running Windows 7 on a Dell Studio 1558 laptop. I am unsure of the graphics card at the moment as I can't access the computer but I know that it is an ATI of some sort.
I was getting frustrated with my external monitor because the screen color was turning dark purplish at times, so I went into Device Manager and deleted both default monitor entries instead of just one under Monitors in hopes that it would've gotten rid of the purple haze so to speak.
I tried unhooking the monitor and unplugging everything before I deleted the default monitor entries in Device Manager, but it didn't get rid of the purple screen.
I have a fairly old notebook Dell Inspiron 4000 with WinMe installed and the display is no longer working assumed due to a bad or broken LCD, which is why I'm using the external monitor.
The external monitor has been working fine for months until it started turning purple on me when it was being used with the notebook. When the monitor is hooked up with my desktop, the screen color is just fine.
The notebook has got a lot of storage on it. During the boot process on the notebook, the external monitor lights up at one point (no longer purplish), but goes blank/dark after a few seconds and says it no longer is getting a signal from the notebook
My Aspire 5738 is hooked up with AOC brand 27" HDMI external monitor by HDMI cable. This monitor is without any speakers. I made this monitor PRIMARY to 15" Aspire 5738 screen.
When I play a DVD/CD using ROM drive NO SOUND comes out from built-in speakers of Aspire laptop. But picture runs on AOC monitor which is not useful. Aspire 5738 has TWO sound processors in device manager. One is Intel (Default) and other one ReaLTek, both are HD quality.
"How to configure (If Possible) any of the TWO sound processors to HDMI" OR any other practical solutions?
My Aspire 5738 is hooked up with AOC brand 27" HDMI external monitor by HDMI cable. This monitor is without any speakers. I made this monitor PRIMARY to 15" Aspire 5738 screen.
When I play a DVD/CD using ROM drive NO SOUND comes out from built-in speakers of Aspire laptop. But picture runs on AOC monitor which is not useful. Aspire 5738 has TWO sound processors in device manager. One is Intel (Default) and other one ReaLTek, both are HD quality.
"How to configure (If Possible) any of the TWO sound processors to HDMI" OR any other practical solutions?
my resolution on my external monitor wont display correction when hook up with the XPS 1647.
The connection is HDMI. Resolution has been set to the highest recommend 1920x1080.
If you look at the picture below, the edges of the screen won't fill up the whole screen, making everything so small and hard to read. I already turn off the display on the laptop, making the monitor as my default screen.
On my previous XPS M1530, the Nvidia 8600GT can display the resolution correction.. I find it hard to believe that ATI card are not capable of doing that or there might be something wrong with my setting
How to install an external monitor to an HP 15 Notebook PC?
View 4 Replies View RelatedI just got an HP Envy, 17 inch, and I have an HP 25 inch monitor I would like to connect to it. It has the "old style" connector which was supported on my old HP Entertainment Notebook. Not on the new one! What kind of adaptor do I need to get? I do have an HDMI port on the left side of my laptop. Do I need just a regular HDMI cable?
View 2 Replies View RelatedLaptop was working fine up until yesterday. Then this happened...
1. Pressed the power button to turn on the laptop
2.the fans run and the computer makes its usual whirring noises as it would normally do whilst booting up.
3.the screen however remains completely inactive. As if the laptop is off.
4. I turned it off and on again several times. Once it came on and worked as normal, I could access all files and backup everything.
5. This morning I turned it back on and it has done the same thing. Makes the sounds as normal but screen is inactive.
I have turned off and on again and connected an HDMI cable to an external screen but there is no signal.
Tried (and sometimes successful) to connect HDTV to laptop, Inspiron 5720. Now laptop screen does not display (goes black) without an external monitor physically attached. Tried using Projects and clicking on single laptop display, but if I disconnect the external monitor, the laptop screen just goes black. Not very portable if I have to lug around a second display.
View 1 Replies View RelatedI cannot connect my Probook 4430s to external monitor. I also have problems on the following device drivers. Are theDo I y related? need to download a new driver? What to download?All I want is to be able to use a larger monitor.
Port_#0006.Hub_#0004
USBVID_03F0&PID_311D&REV_0001
USBVID_03F0&PID_311D
[code]...
I have a brand new HP Envy X2 (15-C001dx) with Windows 8.1. So far it works fine by itself. I tried connecting an external monitor to the laptop using an HDMI cable from the laptop to an LG L246WPQ display. The problem is that 10-15% of the left side of the laptop screen content does not appear on the external monitor. Missing from the external monitor is the word "Start" in the upper left corner along with roughly the 2 leftmost columns of tiles. This occurs in both "Duplicate display" or "Only display on screen 2" modes. This is using a resolution of 1680x1050 which both the laptop and the LG appear to support. Using the touch screen on the laptop I can scroll the tiles to the right and see the missing leftmost columns. The information that is displayed on the external monitor begins as far left as that monitor will display. In other words, there is no black/blank area on the left. Except for the missing information on the left side, the content of the rest of the external monitor looks fine. I updated the laptop's video driver to the latest on HP.COM. No change in behavior. I tried every option I could find on the LG OnScreenDisplay, but nothing made the display any better.
View 2 Replies View Related