I have an XPS M1330 with a faulty hard drive. The warranty has just expired (2 weeks ago) and Dell were not able to give me the part number to buy a replacement hard drive myself.
Do you know if these notebooks would accept any standard 2.5" SATA drive?
OR are the laptops BIOS protected or have some other Flag set on them so that the laptop would only recognise drives from certain manufacturers
Originally posted thread here .....
View 9 Replies View RelatedI want a 7200 500GB drive in the E6400 that I plan to purchase..
Dell doesnt offer a drive this big.
These drives are quite cheap these days. So i will get the the E6400 with an 80GB and swap it out with an aftermarket 7200 500GB.
Im hoping to use the OS disk that comes with the machine to install Vista on the new drive.
I received a replacement hard drive, but the description says it is a 250GB 5400 RPM hard drive. The hard drive I have on the system is 250 GB 7200 RPM. I also checked further specifications on the internet.
The replacement Toshiba 250GB hard drive (MK2552GSX) has 8mb buffer while the hard drive currently on the system Seagate 250 GB (ST9250421ASG ) has 16mb buffer.
Has anyone receieved a weaker hard drive as a replacement. I have to return one of them as part of the warranty service
I have a M6300 that has a 80GB hard drive that I would like to replace.
I am looking for the largest size possible with good read/write speeds
I bought a hard drive (Seagate 320GB SATA 2.5") intending to upgrade my storage space which is currently 160gb. I checked to see if the drive was compatible (the drive my HP dv6500t shipped with was a Toshiba MK1637GSX) and I had figured it was since both were SATA.
The hard drive arrived today. I decided that before I begin putting my drive image on the new drive that I check to see if it'll fit. I open it up and take the drive out and to my surprise I see that the drive that was inside the laptop had some kind of pin-connectors.
The Seagate laptop did not. I took off the caddy that was holding the hard drive, but I noticed that the pin connectors were a part of the hard drive itself.
So this has left me rather perplexed. I looked online and found caddies and SATA connectors for a dv6000 laptop but they were going for around $35.
Is this normal or am I just missing something here? Should I have ordered a different drive?
My laptop is a Pavilion dv6500t purchased October, 2007.
I replaced the 40 GB hard drive that came with my VGN-B100B with a Western Digital 250 GB drive. When I installed Windows XP Professional on it, the partition was only 127 GB. The WD drive is a PATA, which I understand to be synonymous with EIDE, which should work on this computer. Is there a limit to how large a hard drive this computer will recognize?
View 6 Replies View Relatedsteps to replace a hard drive on a Sony VGN-NR110E/S.
View 4 Replies View RelatedI got a VGN-NR260E to fix and the HDD is reporting problems, now most laptops I've worked on have a HDD panel on the bottom, not this one, and Im thinking I have to take it apart fully.
View 3 Replies View Relateddoes anyone have a tutorial for sony vaio vgn-p530h hard drive replacement
View 4 Replies View RelatedI went ahead and followed the information on this forum on adding a second hard drive through an optical drive caddy
DIY: Adding SSD or HDD storage using an optical bay caddy
I've posted the problem in that thread ... and I may be breaking some rules posting a new thread ... I just know there has to be a simple answer to this that I am not seeing ... so I am desperate, so here we go!
I've added the Optical drive caddy into my M1330 successfully... at first. My computer was actually in hibernation when I took it apart (battery and all) to install the caddy.
I took out the slot load drive and installed a Momentus 500gb drive. Put the Comp back together and started. Vista recognized the drive as if it were just plugged in I could browse files and copy to and from the drive.
On reboot though, the drive is no longer detected. The "fixed bay device" notification in the bios under "Device Info" claims that nothing is there when it would normally show the DVD drive.
Device Manager does not show the device once Vista is booted, and it does not show up when I scan for new hardware. The computer boots fine as it did before, and I even rebooted using a thorough POST behavior to try to force it to recognize the HDD in in the caddy the PATA slot .....
I would like to purchase a Z590 which is currently configured with a SSD Raid of 60GBX2
I was hoping I could break the raid configuration and use one SSD for OS and other for data.
But 60gb for data might be less. Can I replace both SSDs with
1 2.5" SSD and 1 250 GB standard SATA notebook hard drive
Installed replacement hard drive in Latitude E6510. Ordered same drive as originally installed from Dell. When I try to install OS on new drive I get the "No Boot Device Found" error. When I enter set up the HDD and DVD drive are shown as installed. I changed the boot sequence to have the DVD run as first boot device.
View 1 Replies View RelatedI purchased my M1330 over a year ago, with an internal 120gb hard drive.
I just purchased the HITACHI Travelstar 7K320 from NewEgg, since I'd like a both faster and larger drive.
However, I am curious about the following:
Right now, my hard drive is flush with the side of my laptop. It has a black trim on the side that is the reason for the flush side. It came this way from Dell. However, in purchasing the new hard drive, what can I do to make the side flush again, as well as the hard drive secure (dust, falling out, etc)? Can dell provide the part (side cover)?
For your reference, you can notice the hard drive cover in this photo (far right of the laptop):
I'm currently having issues with a HP Envy dv7, I'm currently running windows 8.1.
I had a little of trouble with my original hard drive (physical damage) and had to replace it, obviously I lost my HP recovery partition and all the extra drivers that come with it,is there any way to get them? And also i can't seem to use my Biometric device since I don't have HP simeple pass , I tried downloading one from other post but it didn't work.
Had some build quality issues with my original M1330 that I finally decided to take care of last month (plastic is warped/not glued down in places).
Now when I log into the Dell Support page with said dispatch # all I see is as follows
My M1330 has developed the "ac adapter type unrecognised" problem which means a new mobo. But it may be. It's an early m1330 with the 633MHz FSB and 2.2GHz cpu.
Do you think Dell will be able to replace like with like? I'm rather hoping they'll give me a 2.4GHz with 800MHz FSB as replacement as that's the nearest CPU match without giving me something inferior.
seeing as I'm getting ready for my 1330's second Mobo replacement, I've made a list of what to check after a mobo replacement. The first part of the checklist is what you really should test while the RegGuy's still on location and the second & third parts are what you need to verify (in most part) that the replacement mobo is indeed ok.
What the rep will check on your behalf is that the Notebook fires up and loads your OS. This of course implies that the power-on switch, monitor, hard drive, keyboard and trackpad are connected and that the main chips (cpu, graphics, chipset, audio, etc) are indeed functioning.
But that's about it so the rest is up to you ...
my m1330 is showing signs of gfx/mobo failure, but there is no real way to prove it to the techs.
Is there a way to call in and get my mobo replaced without forcing the failure? ...
Well, my Nvidia 8400 died for second time and I called Dell to replace it. After asking for a sustainable solution and to ensure me that I won't have the same issue once more, they said that they will install me a new motherboard revision which reduces the possibilities of having my GPU dead.
Thus, they replaced the motherboard. I didn't format my system but kept my Windows Vista Ultimate x64 installation.
After using the system for a couple of hours I realized that the system was under-performing. Then I checked with CPU z utility and found out that the CPU clock was stuck @1,6GHz (although my power scheme was high performance). My processor is the T7500. The system was overheated and the clock speed was reduced (I guess). The thing was that I could almost do nothing, not even surf on the internet. This makes my laptop unable to deal with applications that need lots of CPU power.
Does anybody else face the same problem? Is there something I could do to return to the old situation? Should I contact Dell and complain? It is a huge problem cause half of my applications cannot be used any more!! After a few minutes of use the laptop stops performing normally!
Could it be that if I format my HD and make a fresh install the problem will be resolved? (I repeat that I didn't format my system after the MB replacement).
So My M1330 was part of the defective batches of Nvidia Video card. A dell tech guy came and replace the motherboard and also a defective battery. I assume that the hard drive would work the same and I assumed I didn't need to format. My current hard drive was just taking forever to boot up, and was just so slow. I figure i needed to reformat.
I used a new 320GB hard drive i was planning to replace the current drive with. Now that its fully formatted. It's still unbelievable slow. I though the speed step might not be working current but i used wcpuid to test the current speed and it was at full speed. Though the system doesn't seem hot at all. I just cant figure out why its so slow. bios is currently at A12 which is the lastest
Could anyone recommend a replacement hard disk for a Dell Inspiron 700m laptop. I am running Windows XP Pro SP3.
I would prefer a larger size disk greater than 250GB. I did search the forums and I found very little info for the 700m hard disk problem I have.
I have Aspire 5112WLMi (conf. in the signature) for 4 years now, and my HDD is almost done!
I want to buy a new one with much biger capacity (thinking about WD 320GB), how can I know will my system support this HDD?
Has anybody installed this big HDD on 5112WLMi?
Using my inspiron 2330 (only 18mths old ) as normal next thing it tells me it encountered fault and has to reboot anyway it keeps saying scanning and repairing drive (c) then does not allow me to log in so i manage to get into bios to do a scan and it guves me a error code of 2000-0142 validation code of 112406 and and then says harddrive 0-s/n wd-wmc152946178
When i finally manage to log in my desk top screen is flashing and keeps telling my hard drive fault ....
Something recently happened to my laptop, and now whenever I boot up my laptop, I get a message stating that "No drive detected", and I don't know if the hard drive might be damaged or not.
I tried connecting the hard drive directly to a desktop pc since it's a sata hard drive, but my desktop pc just froze on the boot screen whenever this hard drive was connected.
I also was going to try and use a hard drive external case to maybe connect it to the pc this way, but I wasn't sure if it would work
I'm thinking of removing my DVD drive and replacing it with a caddy and hard drive as explained here.
I don't use the DVD drive very often and would much prefer a 500GB or 1TB hard drive in there. The DVD drive can then be used externally via the eSATA port using this cable.
The ideal solution would be to use this NewmodeUS caddy as it supports the larger 12.7mm 1TB 2.5" hard drives and has a removable faceplate. The problem is the price.
At $55 including postage to the UK plus customs, VAT and clearance fees on top it's going to work out pretty expensive for what is essentially a slimline SATA to SATA extension
I hate for this to be my first post, but after looking everywhere on the internet and on this site (I've been lurking a while) I'm still at the same place I started with my Studio 15 laptop. I'll try to include as much detail as possible.
I had my laptop plugged into my LCD tv via an HDMI cable as I often do, and when I went to close the laptop to use just the LCD, the tv flashed, showed a blue screen of death for a quick second and then went black. I opened the laptop and it was still on, but the screen wouldn't go on.
I restarted my computer and from there on out it kept making a beeping noise and stalling for a really long time at the "Dell Studio/progress bar" screen. After leaving it at that screen for a while the clicking stop and then it allowed me to access the Boot Options and Setup. Under setup, when I click on the drive under SATA hard drive, it shows something like 10GB and nothing more, and I have no options on the screen .....
I currently have a XPS M1210, and am looking to replace the DVD-RW drive installed. I'm trying to shy away from getting a replacement (same model) unit, and would rather use another brand drive .....
View 3 Replies View Relatedgot a customer who called in looking at a SN-S082H/BEBN as a replacement to the stock drive which he says has died.
I checked the Dell site to see if it had any part #'s listed for possible replacements but the only thing it shows was a HDD recommendation.
HP Pavilion Dv5-2077cl Entertainment NotebookProduct #: WQ799UA#ABAWindows 7 64-bit
I have been getting a random blue screen popping up every once and a while, that will "dump my physical memory" or something and then reboot itself after like 30 seconds. my hard drive was the reason for these constant errors. So I backed everything up, in preparation of a real crash. I am in the process of ordering a new hard drive from Newegg.com, and I would like to know if it is hard to replace a hard drive in a notebook, or if I should have Geek Squad do it for $50. Also, I dont think I have the Operating system disc that came with my computer, so how do I order that from HP and how much is it?And last but not least, Is there a post or video with instructions on how to install a hard drive and the operating system?