Lenovo T400 / T500 :: T510 Windows Recovery Failed
Dec 7, 2013
Windows 7 64bit on my T510 has died. When logging in, it hangs on the login screen forever. Windows recovery failed too. It ran for 8 hours and reported error (something like error in restoring a file and disk is full, though my C drive is half empty). After that all the Windows restoration points are gone. So I suppose I have to do factory reset.
My question is, I made two additional partitions on my hard drive using external tools, which store all of my data. So when I do factory reset, will these two partitions be overwritten? How I can recover the system while keeping all my data?
Recently my T510 9 cell battery suddenly stopped working. According to the Lenovo battery utility, the battery condition is poor and it suggests replacing a battery.
However, the battery seems still have 99% capacity, either by Lenovo utility or by other softwares. Before the failing it lasts 3-4 hours and charges normally.
I read several posts online and see some people have similar problems. It is suggested that maybe one of the cells fail so the circuit stopped the battery from working/or the safety circuits just malfunctions? Or indeed I need to replace the battery.
I understand that messing with battery is risky and I believe it is detected as not working for a good reason. However, I am wondering if there is a way to assure that my battery is completely dead, but not a problem with other hardware or the OS, before I purchase a new battery. For example, using a volmeter on the whole batteryto see if I can get a reading, or opening up the battery case and test on each cell?
Is it doable to replace a single cell if one of them fails?
PS: For people who says that they connect two terminals of the battery to a volmeter and see no readings, I believe you also need to ground the safety pin to turn on the battery.
I've got a problem with the laptop Lenovo T410s. I've put the new HDD on it (tried even the same with a different HDD too), and started to instal WIN 7 64-bit from the recovery disks. I used to do it many times so far with different Lenovo laptops without any problems. But this time, a while before the end of the instalation (when processing the sdrivebackup.wim) it stops and comes with a statement: " the recovery process has been finished, please ...." (but I see that the progres bar is far awayfrom 100%) , and finishes the instalation, reboot the computer and it comes the screen with the statement from the Windows Boot Manager:
"Windows failed to start. A recent hardware or software change might be the cause. To fix the problem (...)
File: Windowssystem32winload.exe Status: 0xc000000f Info: The selected entrycould not be loaded because the application is missing or corrupt"
I read a lot about the ways to solve similar problems, but they don't work on my case. The strange thing is, that I can instal WIN 8 or WIN7 from regular Windows instalation disks (not from Lenovo recovery, but from normal universal Windows instalation disks).
As I told before, I tried it in 2 different HDD disks with the same effect. It looks that the recovery instalation stops before the end without instaling some files which are missing later during starting the system.
I bought a T510 few days ago and was surprised to see this machine has ridiculously low volume. I have tried everything including the tweaks in Smart audio and removing audio limiter but still the volume is very low. On my dell 1525, I never go past 40% volume on my headphones but on T51o, I am using 90-100% volume to watch videos on live streaming websites.
Is there any solution to boost the volume on T510? My system is with windows 7 ultimate (64-bit) and audio device is Conexant 20585.
I have a T510 with a 128GB Samsung Solid State drive that is out of space. I would like to replace it with a larger one, preferably a Samsung 840 series with 500GB. I do not want to get an additional drive for the ultrabay, but rather replace the one I have. While shopping and researching, it looks like the drive I have is 78.5 x 54 x 5mm and all of the potential replacements are 100 x 69 x 7mm. Will this fit into the existing drive space? If it will not, what should I get? It also looks like the current drive is SATA II while all replacement options are SATA III.
I was watching a film on my projector, from my Lenovo T510 laptop, using a Display Port to HDMI cable. There was a thunderstorm and a powercut during the film, but my laptop wasnt plugged in at the time. Then when I touched the Display port end of the cable, which is plugged in to my laptop, it was too hot to touch, and had was slightly bulging and mis shapen! Now it has cooled down and just looks and feels normal. Very strange, and I dont see how it could have been related to the storm and powercut, but it seems a bit too coincidental! I have used this cable multiple times before and never noticed this, but then again maybe I wouldnt have ever touched it until it had cooled down. But I it was pretty much metling it was so hot, so I would think Id notice it.
I have a lenovo T510 which has a maximum res of 1366x768 it has nvidia NVS 3100M graphics.Ive checked with nvidia and it says the gfx card supports 1920x1080.
If its possible could i buy a 1920x1080 lcd and fit it to this laptop without any problems.Or shall i just buy a 1366x768 lcd.
I just got a Thinkpad T510 and when I turn on the NumLock a little black box appears on the screen when it is on and I want to know how to make that not appear when the NumLock is turned on,
I've got little issues with screen brightness on my T510.
Sometimes after returning from hybernate/sleep I cannot control screen brightness at all (chaning it by Fn+Home/End or from PowerManager just dont work).
I've just out my hdd to check whether the ssd will fit there, just checked whether the slot is ok. Then I put back the original HHD very carefully. After that I opened the extra RAM slot, took it out and put it back, also VERY carefully. I didn't harm the laptop in any way.
Then I turned the computer on and it was just a black screen, nothing happening. No indicators lighted up, except for power button. I cannot enter BIOS, no response whatsoever.
I was originally under the impression that my laptop (Thinkpad T510 4384-DS9) had NVIDIA Optimus display technology, however, I cannot find any OPTIMUS options in the BIOS under display (or any other section for that matter).
The reason I would like to know is that I have recently purchased a docking station (model: 4338) and 3 external monitors which I would like to use simultaneously.
Forgetting the fact that I'm using Linux, and that for most people this wouldn’t be a challenge worth undertaking, I would just like to know if my system actually supports 3 external monitors and the laptop screen concurrently using the docking station.
I have a T510 running Win7 64-bit. For at least 3 years, I have had the same dual monitor setup (2 DoubleSight DS-1900S) running off my minidock with the laptop closed. The rgith monitor is the primary, running off the DVI port, while the left uses the analog port. I was away for a week at Scout camp, powered on the system once while I was there, and when I came back to the office, my monitor setup started failing.
Specifically, the right screen is active but it no longer displays the signal being sent to it. When I powercycle the screen, I can see the display for about a quarter of a second, then it goes blank. When the problem first started, I could cycle it about 20 times and eventually it would stay on, until I left the unit overnight and it went to sleep, at which point the probelm started again.
Sounds like a wonky monitor? I have a backup set of monitors that I swapped in, and had the same exact problem, so that appears to rule out a mechanical defect. More fun facts: I can only use the laptop screen as a standalone display. I cannot get the multidisplay control panel to open, even though my left screen is powered up. However, one of my programs that normally launches to my right (main) screen will still launch, but not to my laptop screen. It really wants to live on my right screen, even when that screen is not powered on (I can close the program by accessing the icon bar at the bottom of my laptop screen).
I have new T430s with Windows 8 on it (preinstalled by Lenovo). Everything is fine except they cut a huge chunk of my expensive SSD hard drive for so called "recovery partition". So now I have 2 tasks to accomplish:
1. Create recovery media on DVDs; 2. Remove that recovery partition from my HD and attach the space to main partition.
On Windows 7 I would use "Rescue and Recovery 4.5" tool from Lenovo to do that. But it looks like the tool is not available for Windows 8. When (if) it will be available? Or any other way to accomplish the above tasks?
I have purchased a Lenovo Thinkpad T430. This laptop came with pre-installed Windows 7 Pro. However I want to use Windows 8 which I have a recovery disc for.
I built in a SSD instead of the optical drive. So I don´t have a optical drive. On this SSD I want to run my OS.
With a software from Samsung (manufacturer of my SSD) I was able to copy the Windows7 OS on my SSD.
As I mentioned above I bought a laptop with installed windows 7 pro and a Windows 8 upgrade disc. Therefore I got the "Operating System Recovery Dis Windows 8 Pro. (OEM Activation 3.0 Required)".
The problem now is that I have an upgrade disc but no optical drive. So I created an image of the upgrade disc and with this image I have created a bootable USB stick with the following program:
[URL] ....
When I boot my laptop using the bootable USB stick everything seems to be working until to the point where I have to accept the EULA.
So I chose a language, and clicked on "I accept the agreements".
When I want to click on "next" I got a error message "recovery failed".
Please have a look on the following picture taken with my smartphone. The language used in this picture is german as i live in Austria.
Link to image
How I can upgrade to Windows 8? Why the upgrade disc is not working?
I recently bought a T530 with Windows 8 pre-installed. I want to create recovery disc(s). However, in the "Create a recovery media" wizard, I don't have the option of selecting DVDs if tick the option "Copy the recovery partition to the media". I have a bunch of DVDs lying around and I would like to use them. Not to mention that I don't intend to buy USB drive just for this purpose.
I have been sent 4 sets of Windows 7 Recovery Media from Lenovo over the past week and a half. These DVDs are unusable as they will not boot because they were created as non-bootable DVDs. When looking at the DVDs, they all just have 1 file on them - 0A44006.dvd. I was sent a set of the 32bit version and it has multiple files on it with Bootmgr and 6 directories and will boot just fine. The 64bit DVDs obviously were created and replicated without any of these files to make it a bootable DVD.
Both Targeted Read Test and SMART Short Self Test scan failed during a couple of runs.
Error while reading sector 680448279. The test found 1 sector errors. Failed (Error code: WHD20-P8U)
The device reported the following status: The previous self-test completed having the read element of the test failed. The first failing LBA value is 680448279 and the failure occurred after the device had been operating for 7990 power-on hours.
I believe my fingerprint reader died a death after a windows update. I have tried reinstalling drivers several times but no luck, the computer doesn't even seem to recognise that a scanner even exists anymore. Its incredibly frustrating...well not as bad as this constant blue screen and crashing. I don't really understand the reason for it, but to be fair I don't really know what im looking for when the blue screen appears....it mentions something about a usb driver i believe. There isnt even anything plugged in to any ports when the crashes take place.
Im really not happy about these issues with a laptop that is no more than 6 weeks old.
My T500 was slammed very hard one day, once I reboot, it worked for half hour and gave up. I tested it via BIOS, it gave me error code 0000 read verification failed.
I presumed the HD is dead, inserted a healthy one inside and works fine for a couple of hours and gave up again, tested through BIOS gave me the same error code.
I have a T440s lenovo laptop whose motherboard was replaced a few months ago.
Today I wanted to make a clean installation (windows 8) using the recover USB key I created before the motherboard replacement (note that I already used it and it was working before changing the board).
It goes through the different steps, deleting files and creating the partitions, but when it is done the computer is not able to boot on the hardrive. I have the following messages :
Intel (R) Boot agent Ge v1.5.43 copyring (C) 1997-2013 , Intel corporation ............. initializing and establishing link...
PXE-E61 - Media test failure, check cable PXE-M0F - Exiting intel boot agent (so looks like it is trying to boot on the pci lan)
Then it comes back to the boot menu where I have a choice between : ATA HDD0 PCI LAN
If I select the first one nothing happens, and the the PCI LAN gives the above error message.
I tried to reset the bios parameters to default but it did not work. So I am wondering if it has something to do with some change in the motherboard ID, bios version....
I also launched the lenovo quick storage device test to check the hard drive and all was ok. I had to change a bios option to UEFI (the new motherboard was set by default to Legacy, messing up all the recovery process)
I have tried to make a fresh Windows 7 installation, but after installing updates via Lenovo System Update the system gets corrupt.I replaced the hard drive on an T400 and loaded a image that I had on to the drive. After a installing a few updates and program I noticed strange system beaver. So I did a system file check and it came back that files was corrupt and cold not be repaired.So I did a new fresh Windows install. But it to became corrupt after just running Windows Update and Lenovo System Update.So I ran some hard drive and memory diagnostic without find and problems.
Then I did a new Windows 7 install again. After I installed all recommended updates from Windows Update I did a system file check, all OK. The I installed Lenovo System Update and all its recommended updates and did a new system file check, Windows system files corrupt. What Lenovo update is destroying the system?
I bought the machine t430 thinkpad three months in the United States.
Currently the program to check the hard drive by LSC, the error message is: Targeted read test Failed
Diagnostics SMART status test Passed Targeted read test Failed Random seek test Passed Funnel seek test Passed SMART short self-test Passed SMART drive self-test Passed
The time machine is still time 8 months warranty. Hitachi Hard Drive 500 GB 7200 rpm / min
Is it due to the speed that new hard drive used for 3 months has been corrupted? In case of warranty, Lenovo does not provide a Windows license again, right?
The parameters of the hard drive Hitachi-HITACHIHTS725050A7E630-TF1500Y9HK360B Result code: WHD01V002-UI7X0H
I have a brand new T440 which I am populating and customising.I created a new partition on the HDD using MiniTool Partition Wizzard. That may have created the problem - I can't create the recovery media. I get a message that the files are not there. I should have done it before partitioning - too late now.
However, using the Partition Wizzard, I can assign a drive letter to the Recovery partition, and it becomes visible in Windows Explorer (File manager). I can copy the content on an external HD drive.
I replaced the hard drive on my T410 2516-CTO with an SSD and booted the system with the recovery disc created from the original hard drive/OS. Neither the Recovery/Rapid Restore disc or the Product Recovery discs (1-7) are booting. The Recovery/Rapid Restore discs produce blue screen and the Product Recovery discs appear not to have a bootable operating system.
I am unable to create new recovery media from my old hard drive because I used it to create the defunct recovery media.
How to get the Win7 (64-bit) operating system and recovery partition installed on the new hard drive.
I need to do a recovery on a T420s. I want to recover to same state as out of the box. I already backed up all the data. I am using the disc provided by Lenovo but cannot seem get the disc to start the process. I think I set the DVD as the first boot device but it goes right past it and into the normal start up process.
Is there a way to start the process besides from boot up?
I recently bought a reconditioned Lenovo T410 and have to perform certain actions to get myself set up. One of these was to create factory recovery discs using Rescue and Recovery.
As this wasn't already installed on the machine, I have downloaded it (tvtvrnr4.52_005en.exe) but it won't install. I am getting the message 'Error 25014 There was an error installing the Rescue and Recovery boot manager. Return code: 6'. How to resolve it or an alternative way or creating recovery discs?
I purchased my T420 one year ago and have sufficiently "hosed it up" to the point I wanted to do a factory restore. I saved all my data then proceeded to create the CDs from the Q drive factory restore. I followed the instructs for more and more CDs and once I got up to #12 I noted that the time it was taking to create them was down from several minutes to several seconds. When I got to CD number 18 I thought "this is ridicules" and I popped CD 11 back in to look at its content (via Windows Explorer). I noted it had two folders: 1) Factory restore (or something like that) which was over 500 MB in size and 2) something about data. This "data" folder contained 1 KB of data. I then looked at all subsequent CDs (12-18) and they all only contained this data file. So, rather than continuing to make these (basically empty CDs) I stopped.
I then put the first CD in and rebooted the machine. The factory restore started and I swapped CDs until I got to 12. I put 12 in and it said the required data was not present and to insert the next CD. I did this until I ran out of the CDs I had created. I had to "X" out of the restore app and now when I boot I get nothing but a dimly lit screen and a flickering hard drive light! Am I totally hosed here? How many CDs would it have required had I kept making them? I am ( obviously) a novice.
Lenovo T400 to install Windows XP on it..It previously worked fine with windows 7 and 8.1.so it boots in windows XP preinstall screen, it formats hdd and like usual installation automatically restarts after that BUT its black screen, lights and sounds show that it works and goes to next screen BUT the screen is still black. Powering down and turn on again is not showing any screen picture. Opened it removed Bios battery, turned up after few on and off it starts it reset bios.
So now there is picture and it goes on the next screen of windows instalation like normal, after installing devices and stuff it automatically restarts like usual BUT it has NO screen again, black screen, lights and sounds again show that its loading windows end instalation screen but no picture on the screen. Reset BIOS again, it starts normaly and this time it shows BSoD with code 0x7B, after BSOD Black screen again..Maybe its a BIOS setting?!? tried installing with drivers for AHCI and tried installing without drivers for Compatible , what else can it be? Updated the bios to latest version, same result. To say it again - it works fine with other windows, but XP must be installed
I am using T440. I just upgrade the operating system from windows 7 to windows 8 using recovery disk. I upgrade according to the manual paper in the box.
The issue is, the windows 8 is installed in my HDD with capacity 500GB and the SSD 16GB are not detected. My question is, it should be installed in my 500GB HDD or the SSD drive? What are the correct steps to do recovery if I 500GB HDD and SSD drive?
