I have a lenovo T510 which has a maximum res of 1366x768 it has nvidia NVS 3100M graphics.Ive checked with nvidia and it says the gfx card supports 1920x1080.
If its possible could i buy a 1920x1080 lcd and fit it to this laptop without any problems.Or shall i just buy a 1366x768 lcd.
all available screen resolutions on the full hd version (1920x1080) of their 6930/6920? I'd like to know if it can be reduced to 1366x768 before I buy the notebook so I can have a true pixel for pixel reproduction when connected to my HD ready plasma. I know I could just buy the lower resolution version of this notebook but I've read that 768 vertical pixels is not enough for this 16" display, too much scrolling it seems and one review even said that graphics on the screen look almost jagged when compared side by side to a notebook with a higher resolution.
View 10 Replies View RelatedI have a Latitude E6530 and I'd like to upgrade the resolution to 1920x1080. What cable and LCD part # (or compatible) do I need? The panel is easy enough to replace but I have no idea about the LCD cable.
View 9 Replies View RelatedI have a T510 with a 128GB Samsung Solid State drive that is out of space. I would like to replace it with a larger one, preferably a Samsung 840 series with 500GB. I do not want to get an additional drive for the ultrabay, but rather replace the one I have. While shopping and researching, it looks like the drive I have is 78.5 x 54 x 5mm and all of the potential replacements are 100 x 69 x 7mm. Will this fit into the existing drive space? If it will not, what should I get? It also looks like the current drive is SATA II while all replacement options are SATA III.
View 3 Replies View RelatedWindows 7 64bit on my T510 has died. When logging in, it hangs on the login screen forever. Windows recovery failed too. It ran for 8 hours and reported error (something like error in restoring a file and disk is full, though my C drive is half empty). After that all the Windows restoration points are gone. So I suppose I have to do factory reset.
My question is, I made two additional partitions on my hard drive using external tools, which store all of my data. So when I do factory reset, will these two partitions be overwritten? How I can recover the system while keeping all my data?
I was watching a film on my projector, from my Lenovo T510 laptop, using a Display Port to HDMI cable. There was a thunderstorm and a powercut during the film, but my laptop wasnt plugged in at the time. Then when I touched the Display port end of the cable, which is plugged in to my laptop, it was too hot to touch, and had was slightly bulging and mis shapen! Now it has cooled down and just looks and feels normal. Very strange, and I dont see how it could have been related to the storm and powercut, but it seems a bit too coincidental! I have used this cable multiple times before and never noticed this, but then again maybe I wouldnt have ever touched it until it had cooled down. But I it was pretty much metling it was so hot, so I would think Id notice it.
View 3 Replies View RelatedRecently my T510 9 cell battery suddenly stopped working. According to the Lenovo battery utility, the battery condition is poor and it suggests replacing a battery.
However, the battery seems still have 99% capacity, either by Lenovo utility or by other softwares. Before the failing it lasts 3-4 hours and charges normally.
I read several posts online and see some people have similar problems. It is suggested that maybe one of the cells fail so the circuit stopped the battery from working/or the safety circuits just malfunctions? Or indeed I need to replace the battery.
I understand that messing with battery is risky and I believe it is detected as not working for a good reason. However, I am wondering if there is a way to assure that my battery is completely dead, but not a problem with other hardware or the OS, before I purchase a new battery. For example, using a volmeter on the whole batteryto see if I can get a reading, or opening up the battery case and test on each cell?
Is it doable to replace a single cell if one of them fails?
PS: For people who says that they connect two terminals of the battery to a volmeter and see no readings, I believe you also need to ground the safety pin to turn on the battery.
I bought a T510 few days ago and was surprised to see this machine has ridiculously low volume. I have tried everything including the tweaks in Smart audio and removing audio limiter but still the volume is very low. On my dell 1525, I never go past 40% volume on my headphones but on T51o, I am using 90-100% volume to watch videos on live streaming websites.
Is there any solution to boost the volume on T510? My system is with windows 7 ultimate (64-bit) and audio device is Conexant 20585.
I just got a Thinkpad T510 and when I turn on the NumLock a little black box appears on the screen when it is on and I want to know how to make that not appear when the NumLock is turned on,
View 7 Replies View RelatedI've got little issues with screen brightness on my T510.
Sometimes after returning from hybernate/sleep I cannot control screen brightness at all (chaning it by Fn+Home/End or from PowerManager just dont work).
I have got latest nNvidia NVS 3100M drivers.
I've just out my hdd to check whether the ssd will fit there, just checked whether the slot is ok. Then I put back the original HHD very carefully. After that I opened the extra RAM slot, took it out and put it back, also VERY carefully. I didn't harm the laptop in any way.
Then I turned the computer on and it was just a black screen, nothing happening. No indicators lighted up, except for power button. I cannot enter BIOS, no response whatsoever.
I was originally under the impression that my laptop (Thinkpad T510 4384-DS9) had NVIDIA Optimus display technology, however, I cannot find any OPTIMUS options in the BIOS under display (or any other section for that matter).
The reason I would like to know is that I have recently purchased a docking station (model: 4338) and 3 external monitors which I would like to use simultaneously.
Forgetting the fact that I'm using Linux, and that for most people this wouldn’t be a challenge worth undertaking, I would just like to know if my system actually supports 3 external monitors and the laptop screen concurrently using the docking station.
[URL]
I have a T510 running Win7 64-bit. For at least 3 years, I have had the same dual monitor setup (2 DoubleSight DS-1900S) running off my minidock with the laptop closed. The rgith monitor is the primary, running off the DVI port, while the left uses the analog port. I was away for a week at Scout camp, powered on the system once while I was there, and when I came back to the office, my monitor setup started failing.
Specifically, the right screen is active but it no longer displays the signal being sent to it. When I powercycle the screen, I can see the display for about a quarter of a second, then it goes blank. When the problem first started, I could cycle it about 20 times and eventually it would stay on, until I left the unit overnight and it went to sleep, at which point the probelm started again.
Sounds like a wonky monitor? I have a backup set of monitors that I swapped in, and had the same exact problem, so that appears to rule out a mechanical defect. More fun facts: I can only use the laptop screen as a standalone display. I cannot get the multidisplay control panel to open, even though my left screen is powered up. However, one of my programs that normally launches to my right (main) screen will still launch, but not to my laptop screen. It really wants to live on my right screen, even when that screen is not powered on (I can close the program by accessing the icon bar at the bottom of my laptop screen).
When I connect second display via regular VGA cable I can set the maximum resolution to 1920x1080, although native resolution for my external screen is 1920x1200.
I could just find posts related to similar problems when using docking station - tried some of the solutions, but none seemed to work.
Found this [URL] ... on dpreview - suggests using miniDP to DP 2-link converter (screen has just VGA/DP ports).
I have a T420 with the standard 1366 x 768 resolution. If I replace the sreen with a WXGA 1600 x 900 will the graphics card be able to drive it?
View 1 Replies View RelatedI have bought a Philips Brilliance 272P4 external monitor. Connected the monitor with DVI through docking. I get 1920 x 1080 as max resolution. The monitor displays a note, that I should use 2560 x 1440. I have installed the newest driver to the monitor.
The display card (Nvidia NVS 5400M) is using 333.02 driver, that is the latest recommended. How to enable higher resolution?
Do I get higher resolution with using the displayport insted of DVI port?
I'm looking at a refurbished T430 online, but want the 1600x900 screen - can't find specs for that model anywhere. it's not in any of the PSREF docs at the Lenovo site. If the 2355-A17 has the 1600x900 resolution screen?
View 3 Replies View RelatedI have T410 with Nvidia NVS 3100M with driver version 189.55 connected to external Acer monitor capable of 2560x1440 linked with DisplayPort cable. But, I can't get resolution higher than 1920x1080. What do I need to do?
View 3 Replies View RelatedWould all of you suggest how much much difference 1920x1080 will make over 1366x768 on Studio 15 i.e. 15.6'' screen?
One thing I know is that the font size will be small for more resolution.
Would you list the pros. & cons. of the higher resolution?
Is it worth to pay the difference .....
I have a Lenovo SL410, model 2842. The video card in my machine is Mobile Intel R 4 Series Chipset Family.
Just got a new 23" monitor which recommends resolution setting 1920x1080. I quickly learned that this resolution cannot be achieved with the VGA cable (highest was 1366x768), so I switched to an HDMI cable. When I first booted up the computer after connecting them, it was perfect. Icons were rearranged, but that's no big deal. About an hour later, I had to reboot for another reason, now it's behaving just like it did with the VGA cable. Samsung support says I need to update video card drivers, but I checked that (via the windows interface), and it says I am current. Now I can't get to display with 1920x1080 resolution again.
Since it displayed the higher resolution briefly, I imagine it must be possible to configure the settings so it will stay that way.
Ideapad z510 Full HD 1920x1080 Resolution is not supported !!! The company which i bought Z510 i7 laptop described the laptop as a Full HD but my resolution 1366X768, is that normally ? and all the sites said that this laptop full hd supporter ...
View 9 Replies View RelatedI have bought ideapad y510p with an already pre installed windows 8 and intel vga card. however, i have found out that the nvidia geforce GT 750M is not installed, so i have downloaded the driver with the latest version R331.65 So, normally i have installed the driver. and now even though that i have the latest drivers i wonder why i still have the 1366x768 as the highest resolution and not the 1920x1080. also to my wonder is why when i connect to the monitor it can have the 1920x1080 and not on the laptop screen.
So How to have the 1920x1080 resolution?
My T520 (4242) never crashed until I upgraded the RAM.
Initial config : Single stick of 4GB RAM.
- FRU # 55Y3717
- Samsung part # M471B5273CH0-CH9
Tried to upgrade with 2GB from following manufacturers:
- Corsair CMSO2GX3M1A1333C9
- A-data (don't remember the part #, but matching specs)
Result : Approximately once a day, I get BSOD. The system also crashes often while going in and out of sleep.
The A-data RAM works fine on a different laptop (T500), but I experience crashes when I put it in T520. This makes me wonder if my slot has an issue e.g. dust collected over time that causes a random read error. Or maybe I need to find the exact same part from Samsung to upgrade the RAM.
What else can I try? If it crashes randomly once a day, and works fine otherwise, can I conclude anything about RAM compatibility? memtest86 doesn't show any error.
I was wondering if it is possible to upgrade the built in 4gb on the T440s, Not a big deal if i cant, just wondering because I can actaully get 2 8gb sticks. how to access the built in stick.I only have the built in right now, adding the one 8( hopefully both) later this week.
View 2 Replies View RelatedI have bought new T440p (20AN006NUS). Everywhere was written that it comes with preinstalled Windows 7 pro and also includes Windows 8 pro license.
As I understand license key for Windows 8 is embeded in BIOS. But I have not any installation media for Windows 8 included in the box with laptop. How upgrade to Windows 8 should look like?
i have purchased an 8 gb Kingston Ram module ( KTL-TP3CL). My plan was to upgrade my thinkpad T540p with 12 gb of ram. My configuration is ( i5/4gb ram/hd 4600/W7 pro/500gb hdd). The thing is that I am having second thoughts about having two modules from a different manufacturer and of different capacity.
View 3 Replies View RelatedMy SD card reader became non-functional after a recent upgrade of my T520 to Windows 8.1. Hardware troubleshooting said the Base System Device driver was not installed. I installed the Lenovo System Update software and searched for updates, but the driver was not updated. There is still a yellow warning symbol beside the Base System Device in the device manager. Discovered on the Lenovo driver download website that the card reader in my model is the Ricoh Media Card Reader but there is no driver compatible with Windows 8.1. Would the Windows 8 driver work or is there another solution to get my reader running again?
View 3 Replies View RelatedI recently upgraded my ThinkPad T430s to Windows 8 Pro and ever since my ultrabay battery gives me an error when ever I restart or turn the machine on. It goes away after I hit ok and the battery appears to still be functioning but the error is super annoying. I have the latest drivers and software from Lenovo and I have already had the battery replaced via tech support. Its so annoying i'm tempted to see if I can just get the whole unit swapped.
View 9 Replies View RelatedI have a T440P, Up to recently, I was in Windows 7 with Lenovo Power Manager set with threshold charging limited at 63%, So far so good. Now, Windows 8.1 has been installed from scratch (Not an upgrade).
The laptop with windows 8.1 still stop charging at 63%. But there is no Lenovo Power Manager available for windows 8.1. I don't find any solution to deactivate this limitation...
occasionally, my sl410 started to display in 1280х800 instead of 1366x768, so I see an image shifted to the left and down and black ribbons at the top and on the right. And this happens even in bios. In ubuntu, display setting do not let me change to 1366x768 as there is no such option in a list, only 1280х800, 800х600 and less.
View 5 Replies View Related