Lenovo ThinkPad L R/SL :: SL510 Won't Charge - Not Turn On Without Battery
Jan 26, 2015
Look' s like I have big problem:
1. When I plug charger in to my SL510 lights don't turn on. If battery are take out - laptop is impossible to turn on;
2. If I plug same charger to my second (old r60 thinkpad - lights is turning on and all boots normally);
3. I take charge from my second laptop and test on SL510 - lights still not turning on;
4. If I try to boot without charger (on battery) laptop is working fine.
Is it possible that - when my battery be empty I can never turn on my laptop?
I bought a genuine x220/x230 battery. After I power on the laptop, I got a message: the laptop doesn't support this battery. I tried to update the bios but nothing happend. The power manager said the battery voltage, performance, cycles, LGC battery. If I unplugged the laptop, it is works so the laptop can use the battery just not charge. If it was not a genuine battery I can't see these description or I should also?
Maybe this is not compatible with my x230 because it compatible just x220 and the seller didn't know it?
I have a ThinkPad x240 that is about 2 months old running Windows 7. Everything has been working great until this morning. I was on vacation and did not use my laptop for a week or so. When I plugged it into my docking station this morning, I noticed that the battery was reading 0% charged and was not charging.
Lenovo Power Management showed that the battery is in good shape Lenovo Power Management showed that there was "no activity" - not charging Lenovo Power Management showed no battery #1 - battery # 2 installed but not charging.
Troublshooting so far Tried charging with external power supply outside of docking station - No Change Removed battery, powered unit up and removed all Battery items in Device Manager Reinstalled battery and powered unitup - No change Removed and reinstalled the Lenovo Power Management and Driver / rebooted - No change
Current state: No Power Management software on the laptop - just using the Microsoft stuff (Still not charging). What else I should be trying / checking?
It's been about 5 months since I started to use my Thinkpad X230. Only three days ago it could work for 5-6 hours without charging. I could charge it at home, bring it to school and use it without charging. But suddenly the battery started to die in a short amount of time. Then I explored the battery settings a little bit. I found out it says "Battery Condition: poor" and "Your battery can 47% of its original full charge capacity."
It has warranty until 2015. So can Lenovo send me a new battery if I want so? Or is it a problem that warranty doesn't cover?
So I made a mistake. I've reinstalled the OS on computers dozens of times and never quite had this issue. I have the Lenovo SL510 and tried to reinstall using the dvd drive. I entered bios and changed boot settings so the dvd drive was first and then booted it up but it went straight into windows 7 on the hard drive. I tried again, hitting f12 at startup and specifically selected the DVD drive to boot from and again it would boot directly from the hard drive ignoreing the DVD drive completely. Finally I opened the DVD drive from windows and installed over top of the old OS, planning to delete the old files once the install finished.
The install went fine, everything worked, except I didn't have internet. Turns out that the wireless adapter wasn't being recognized. I opened device manager and it was showing up under "Other Devices" as Network Controller with a yellow exclamation mark. I then proceed to track down and install the wireless drivers after connecting with an ethernet cable. I tried the intel chipset program and it would fail to install the correct driver, I tried the lenovo support program and it failed to install the driver, I manually downloaded and installed the driver and nothing happened. I tried several different wireless drivers and the result was always the same. I was working on the issue for at least 8 hours.
Finally I decided it wasn't worth the trouble, and why not reinstall again. This time I created a bootable USB drive and went through the same process, changed boot order, no result booted from hard drive, pressed f12, selected the USB drive, same result. Finally I installed the new OS image over the existing OS from the USB while the computer was on.
Installing the OS over the older OS was definitely a mistake, but it seems like the core of the problem was that the computer just wouldn't boot from anything other than the hard drive itself I didn't realize the implications that this presented and during the final install of the OS from the USB the computer restarted during installation. Of course.. the computer did not reboot from the USB which meant it simply came up black screen, the OS had already been wiped from the hard drive, but it could not boot from the USB and therefore simply comes up blackscreen.
The first thing I tried to do was reboot into BIOS, wasn't happening. When I attempted to access bios it would simply blackscreen with the power on indefinitely. I obviously tried booting and using f12 several times to try switching back and forth from USB to DVD and so on, but everything just black screened.
So....If the computer couldn't boot from USB or DVD then the only option was to boot from inside the original OS, but doing that caused a massive driver error which I couldn't resolve no matter what I did. And now I'm thinking the computer is completely lost. The only idea I have is to try using a friends computer to install an OS on to the SL510's hard drive and then resintall the hard drive into the Laptop to see if it will boot from it. I've poured over this entire forum and found lots of similar issues but no one seems to be offering any answers or solutions besides an occasional "we're looking into it" message.
My laptop was able to access the internet via my wireless internet connection just fine until a few days ago when it completely stopped working. I can't even view the wireless adapter in my hardware profile anymore. I'm able to connect wired but not wirelessly. I've reinstalled access points, but it didn't work. Nothing has changed in my setup to cause this to stop working.
I don't have a lot of money to replace the laptop that just completely died a month after the warranty expired. It is a Lenovo Thinkpad SL510, S/n xxxxxxx and the product ID is 28479XU. Purchased 3 years ago. I would like to know if I can take the hard drive out (which I was told by a knowledgeable computer person that it is OK with all the data on it) AND put it in my working Lenovo Thinkpad SL410, S/n xxxxxxx, Product ID 28427PU ?The SL510 is really dead. All efforts were tried to resusictate by same computer person.
I have very annoying problem with hot keys for adjusting monitor brightness! After last version of hot keys driver they don't work. I can't increase or decrease brightness! Pressing them down and can't change anything. And there is something more! For example I have adjusted some level from power manager and everything looks good until I don't try to manage brightness with hot keys. I doesn't matter if i want to increase or decrease brightness, it just goes to maximum level!
My SL510 work fine, but just want to know, when I open it for replace the keyboard, I found 1 intel centino mini wifi card N1000 with antenna and at the back an other one is broadcom mini wifi card 802.11g without antenna. My question is: for what function is broadcom mini wifi card 802.11g without antenna? All of 2 are presents as well in device manager...
Whatever I try, I am not able to activate the WLAN card. When I diagnose the network connection it says somethink like "the device is not activated or not installed". However, the device is listed properly as "Intel WiFi Link 100 BGN" in the device manager. All windows updates are installed, and the Lenovo update manager only shows one optional update (Intel Chipset driver for Windows 7) which gives an error when trying to install it.
One strange thing is that, when I use the "ping 127.0.0.1" command in the command shell, only 1-2 out of the 4 tries give a result, the other ones show a timeout error.
What is more, the device works properly with an Linux Live disk, so the hardware seems to be ok. It is just not working with windows 7.
I had 1GB & 2GB rams working fine in the SL510, windows 7 Profession, 62-bit, 320 GB drive. SL510 62-bit can take up to 8GB ram.
I replaced the 1GB by Samsung with a Hynix 4GB. At Crucial they give specs that are replacable for existing ram. I notice one number is different. The original Samsung says PC3 -10600, and the new Hynix says PC3-12800. The 12800 was given by crucial as part of the replacement numbers for the SL510. I bought at EBay used.
Anyway, I bootup and a blank, black screen results. I hear laptop running. I forced closed it and re-started again. Same...black screen as I hear laptop running.
Also, is there a certain order for rams to be installed? Originally, the 1GB ram was first, and the 2GB was below. I installed the 4GB ram below and moved the 2GB to top first position. (in case I want to access the 2GB easily to upgrade with another 4GB)
I have an SL510 thinkpad and I have just installed windows 7 professional 64x. I noticed my wifi not working and in Device Manager there are a number of 'Unknown Devices' I have 3 'Base System Device' alerts, a 'Network Controller' alert and an Unknown Device....
I have the following problem with my computer, lenovo sl 510: when pressing the power button, the computer won´t boot. On the display you can see a black background, in the upper right corner the intel emblem and in the lower left corner you can see "thinkpad". I cannot enter the bios and nothing works. We´ve tried already to press the power button a few times to reset the computer. Didn´t work as well. The keyboard doesn´t accept any hot key combinations.
I want to upgrade my SL510 (28577MG) with a new Crucial M550 512GB SSD. The Crucial website says that the drive is compatible with my laptop: [URL] ....
Unfortunately neither the Windows 8 Install CD nor my BIOS can detect the drive. Here is a list of steps I tried to solve the problem:
Change the SATA Controller Mode Option in the BIOS from AHCI to Compatibility
SSD does not get detected in BIOS2. Update the BIOS to the latest version 1.52 (6JET94WW) SSD does not get detected in BIOS3. Run the 2.5 inch SATA Hard Drive Firmware Update Utility
[URL] ....Utility can't detect the SSD / find any updates4. Look for a firmware update on the Crucial homepage [URL] .... There are "No firmware updates"...
I also installed the SSD in my desktop (Gigabyte GA-MA770-UD3, 770) where it is detected in the BIOS and in Windows 7. So it is definitely in working condition.
Just got a Thinkpad SL510 2847 D2U, Windows 7 Prof.(64 bit).
Often when I touch the Touchpad I see the arrow on screen change to a "button" being displayed. And the button is not like using the arrow. Very difficult to work with it. So I keep moving around Touchpad to get rid of the "button" and return to arrow.
How to rid of this "button" action? Or what am I doing to cause it? I believe I have changed the sensitivity of the touchpad. I'll check again.
my Sony SZ2 (SZ2VP/X - 3years old) did an instant shutdown while running in battery mode (expect Battery around 30%).
After this I tried booting the notebook. By pressing or holding the power button no LED's illuminated.
At home I tried to charge the battery with AC adaptor. Again no LED's illuminated. With or without AC adapter and battery - no chance to get the Sony SZ running anymore.
Because I have no longer warranty I opened the notebook with the help of a repair manual.
You can see some pics in my picasa webgallery.
At this photo the battery connecter looks strange?
Where can I get a cheap repair, or some spare parts like mainboard?
The SZ was already repaired in November 2007 - it got a new Display. Power+battery LED's illuminated, but it didn't start.
Now even the LED's show nothing about the condition.
The computer is in dead state the next morning after I switched its Windows power plan to high performance. In order to unlock power plan options, I disabled connected standby via a registry key in HKLMSystemControlSet001ControlPowerCsEnabled to 0.
After investigating, I read that this computer doesn't support normal hibernate wake-up process other than connected standby. I select shut down option in the menu (hibernate option disappeared). It's possible that shut down option in the menu was actually set to sleep/hibernate in power settings by default.
The battery was at 100% before I last turned it off.
The LED power indicator doesn't light on when power supply is connected on either DC or microUsb.
I have a x201 cto using 64bits Win 7. The wireless adapter is intel advanced-N 6200. However, I found my wireless always turn off suddenly and I can not turn it on anymore (even using Fn+F5) until reboot.
My X1 is about 18 months old. It was fine until today. The battery was low, so I plugged it in. The little blue light where the power connects illuminated, however the battery indicater in Windows did not change to show "charging", and the battery continued to drain.
Over the next hour or so I tried many things like shutting down, waiting, new A/C outlet, new power settings, etc. Tried the little reset hole on the bottom of the laptop. Nothing mattered... the little blue light is on, but the battery just drains.
Eventually, the battery drained and the X1 shut down. When I try to boot, I get a pre-boot message about a critical low power error, even plugged in, so my laptop is now a brick.This is a 3448-34U Thinkpad Carbon X1.
My W540 recently became unable to charge while the laptop is running. When the laptop is off, the battery will charge completely. As soon as Windows (or Linux) boots, the charge terminates and the computer starts running off battery power. The computer will boot without the battery installed, but the computer turns off as soon as either operating system is booted (a few seconds after the desktop appears).
I have tried a different power adapter without success (both adapters are Lenovo 170W supplies) and also put a different battery in (also genunie Lenovo battery) but the issue still remained.
The laptop is still under warranty, could it be the charging circuit on the motherboard? Will I have to ship the laptop back to Lenovo for repair? I am out at sea and might have to wait a while to get back into port to be able to ship the unit back to Lenovo, so I would like to investigate other options.
I received my y510p yesterday and the battery was at 32%. After charging it overnight, it's now at 34%.
I've been reading some threads on the matter, for example: [URL]... and whether my situation was similar, or different in the fact that
A) the other posts indicated a working battery for at least a couple of months, and B) their systems are a bit older and it's possible Lenovo fixed the issue?
I understand there's a power management center in all Lenovo laptops and I can look at that...but even if the settings are to maximize battery life wouldn't this still allow for a charge above 33%?
I recently got the Z500, working under Windows 8.I got a question regarding the battery charge. I work on the laptop for extended periods of time with the power plugged in. Since this is bad for the battery, is there any way to disable the charging or to perhaps remove the battery?I wasn't able to find anything similar for this model.
My Lenovo G570 battery is stuck at 90%. It says plugged in, not charging. It just happened over night. Next day battery refuse to work.
In windows it says battery 90% and is not charging but battery has no charge at all. When I disconnet the A/C power laptop just shutdown immediately. As soon as I unplug the power laptop just shutdown as there is no charge in the battery.
I did reinstalled the Power management and also updated it. I all unplugged reboot in OS, restart, put battery back and boot into the OS back. Nothing seems to work.
I just installed Lenovo Energy Management in windows 8 before I was trying in windows 7. In the battery tab there are two options
Maximum battery Life Optimized battery Health. It is selected to "Optimized battery Health" and won't change regardless of power plan. I click on "Maximum battery Life" and when I open the app again it reset it to "Optimized battery Health".
Lenovo Solution Center say that battery life is GOOD. "Your battery is in good condition".
When i boot the computer to windows, a message pops up saying that i have to not charge the battery up to more than 70%.
It's says that i have to set up something in power consumption options but when i went there i didn't see something relevant to the battery lifespan(in french). Kow to set this up ? between i'm always on the sector (AC).
I bought a new Lenovo Z580 this past June. Shortly after I began using it, a system message popped up explaining to me that since I often have my laptop plugged in, it would conserve battery life if I let the system change my settings so that the battery didn't fully charge -- this would save battery life over the longterm and I would be free to change the setting whenever I wanted to. Well, this has been the biggest mistake ever. I now essentially have a desktop because I cannot find any setting that allows me to change the battery to fully charge (it only charges to 40 or 50%). There isn't any mention of this feature in the user guide materials that I can find and none of the Power Options allow me to change the battery charge capacity.
I have with my Lenovo B5400 is related to the battery. For about two months, on start up I get a loud beep and a message that says "The battery installed is not supported by this system and will not charge. Please replace the battery with the correct Lenovo battery for this system." It's impossible for the battery not to be genuine because I purchased it together with the laptop, so it's all original and stuff. Of course, the toolbar icon for the battery says "plugged in, not charging", so my battery is currently stuck at 88%, although it's not going down. Recently made a BIOS update, but nothing changed ...
Today I received my brand-new E540 from Amazon. Upon inserting the battery and starting the laptop for the very first time, I was greeted by the following error message:
The battery installed is not supported by this system and will not charge. Please replace the battery with the correct Lenovo battery for this system. Press the ESC key to continue.
The message has only appeared once and hasn't been shown on subsequent reboots.
I proceeded to install Windows 7 which worked fine. Under Windows the battery symbol in the taskbar would say "66%. Plugged in. Not charging". I then shutdown the system and re-inserted the battery. Since then the battery appears to be charging normally and when I inspect the battery symbol in Windows it says something like "89% charged. Plugged in. Charging."
Seeing how this is a brand-new laptop, do you think the battery is broken and I should return the laptop, or should I keep it since it seems to be working normally now.
I have a 3 month old Ideapad z510. Last week, the battery indicator started getting stuck on 100%. So when the laptop is not plugged in, If it's about to die.
