I was flashing the newest BIOS to my SR290 last night and in the middle of flashing it froze. I waited quite a while to make sure it wasn't just taking its sweet time but eventually had to pull the battery as holding the power button didn't even do anything.
So I wait a few and then try to boot it back up and it won't power up at all. I plug it in and the charging light won't turn on.
Reason for this is to flash your BIOS the safer way.
Windows has alot of services that can potentially hang the flashing process, hence DOS Mode where no other process is running is the safe way to flash.
First of all get the package here
Extract all the files to Desktop
Go into the folder.
You should see a HP Drive Key Utility.
Install it.
Open the Program With Administrative Permission with Right Click as shown below:.......
Flashing the bios. I have a Aspire 5810TZ. I boot it up and it just says 'acer' and won't go any further. I went to the download page for BIOS on us.acer.com and it has a zip file with 5 files:
JM4151135.exe FLA... GPC_V135.bin readme.txt FLASH.BAT
What do I do? I have tried copying the files to a USB and powering on with Fn-Esc held down. After letting go of the power button and holding Fn-Esc a different screen appears after 30 seconds. I let go and have given it 30 minutes but it is not doing anything. I have read online from other people the power button should be blinking. Do I need to rename one of the files.
Updated: Found a better way to backup Bios only, Please see the end of this message
Let say your Vaio Z is using Bios R4040M3 and you move to Bios R4041M3 to use the official VT support. Later on, you want to move back to R4040M3 to use the Advance Menu hack. Unfortunately, you cannot move back as Sony never publish the R4040M3 Bios update. This is my current situation.
I decided to investigate a way to back up the current Bios. Using a program called Universal extractor, I managed to extracted the files in the original Bios update. The bios update uses a program called Insydeflash to flash the Bios. The Insydeflash uses a file called platform.ini to control its setting.
In the platform.ini file, there is a section called [FDFile]. The section [FDFile] has a parameter called BackupName. If we put in a file name here, the Insydeflash should save your current Bios into that file. Unfortunately, I cannot make it work with the Sony supplied Insydeflash. (version 3.38).
I managed to get the newer version of Insydeflash (version 3.72). The newer version has a new ini section called [BackupROM], as the following:
..........
[BackupROM]
Flag=0
FilePath=c:
FileName=....................
i juse upgraded my sr46gd's bios,and it failed.....
i need to use it tomorrow,is there any way i can do it? i mean re-flash the bios
I installed the 9.2 catalyst + driver and it messed things up big time, so I got rid of it and installed the original driver from Sony site, but it didn't come with the catalyst panel
View 8 Replies View RelatedI got my SR on Christmas Eve. Everything has been great, until now. Today I connected a VAIO USB mouse to use instead of the touch-pad for the first time. Now, it seems like the touch-pad has gotten a mind of its own.
The touch-pad responds, but it seems to be very sporadic. When moving the cursor around, it seems to jump. The movement has also become slow even though in the mouse settings I have it set on fast .....
I've a VGN-SR290 with Vista 64, I'm thinking to downgrade to XP but using official downgrade discs, are these discs available somewhere to buy them?
View 3 Replies View RelatedI'm having a problem with my SR290. The hard drive free space keeps on decreasing. Its fallen from 200 to 175gb, and I haven't installed any new programs. Is this somehow related to Vista Business and does anyone have a solution?
View 9 Replies View RelatedIm having a major issue with my SR290 and Sony Repair Center specifically.
Ok, I just noticed that my hard drive have been running constantly and never under an idle state about 3 weeks ago.
I restored the computer twice but every time I turn it on, the hard drive and the fan makes really loud noises. Even when there are absolutely no applications running,
the hard drive runs and makes obvious noises. I used to be sitting late at night surfing the internet and having absolutely no noise from the laptop, but now even when I just turn it on, its really loud. If I leave it on for over a few hours, the fan exhaust starts to expel really warm air
I am considering the two following models: SR290 and Z540. My question relates to the overall build quality of these models as well as battery life with the extended battery.
Basically Im deciding between these 2 and a lenovo. The lenovo is heavier than both, is well made, and has ridiculous battery life. Just curious as to how the sony's stand up over time.
if i turn the pc off, when i turn back on, no boot up, no chance to press f2 f12 f8 nothing. the only thing that happens is the disk read light stays on, and the caps lock and looks like system lock lights keep flashing. the system will then eventually power off. i removed the battery (the laptop was always plugged into power) and it started. i then placed the battery back and it started normally.
View 15 Replies View RelatedI bought Hp Pavilion dv6 about 11 months ago. When I tried to turn it on today morning, it didnt boot and Caps Lock light is blinking 3 times.I searched on internet and found out that its a memory problem.
View 6 Replies View RelatedI have been having problems getting my laptop to boot. I've performed a laundry list of repair options and nothing has worked. As of this moment, I've managed to narrow the query down to the flashing LED light code FLASHING Num Lock-SOLID Caps Lock-Solid Scroll Lock. I've done some further research and I've only managed to get sketchy information at best. It is saying that the problem has something to do with the processor or the system dock--if that information is reliable. I've had contradicting answers on that. I've reseated the processor several times, even switching the processor with a virtually identical processor from my WORKING Inspiron 1501 with no change. And just to confirm that the processor initially seated in the 1526 is working, I have put it in the 1501 and it works. I've swapped compatible components between both machines and everything has worked after being seated in the 1501.
To recap the light code...Flash/Solid/Solid.
I was flashing my bios of my dell xps studio 16 (i don't know which 17xx it is... it has i5 and 4gb of ram. some ati vidfeo card with 1gb of vram, 15.6 LCD)
And then it froze for about an hour. So I unplugged power, took out battery and tried to boot it up. To my dismay, nothing showed up on the screen.
I have so much stuff on my HD that I need.
What are some ways to fix my laptop? Do I have to send it to dell? Will I lose all my data?
Last week I received my brand new Dell Studio XPS 1340. After some days I got the "Power Adapter cannot be determined .....". So I called Dell Tech Support. He told me to flash the BIOS from A02 to A03. So I did. Under the flashing I got a bluescreen. So the information on the BIOS was gone. So yesterday a Dell Techincan came to my house and replaced the motherboard with a new one. I noticed that this motherboard has BIOS version A01 (the oldest one). I also noticed that the processor fans is always on 4000 RPM. It never slows down to 2000 RPM, even if the temperature is on 40 degree celcius.
So I though this had to be something with the old BIOS version. So I called Dell, and I tried to flash from A01 to A02. But the same bluescreen came, this time, lucky for me, before the flashing! So nothing get destroyed!
Anyway, Copy paste the dump file here:
Seems like PHLASHNT.SYS has something to with this? Have someone have this same problem as me? The fans never stop, and I think its because of the old bios version. And:
1) No errors on the diagnosic test (full system scan)
2) I switched from Vista 32 bit to Vista Business 64 bit (original) with the signed drivers from dell.com (all my drivers are verified)
Code:
*******************************************************************************
* *
* Bugcheck Analysis *
* *
*******************************************************************************
DRIVER_VERIFIER_DETECTED_VIOLATION (c4)
A device driver attempting to corrupt the system has been caught. This is
because the driver was specified in the registry as being suspect (by the
administrator) and the kernel has enabled substantial checking of this driver.
If the driver attempts to corrupt the system, bugchecks 0xC4, 0xC1 and 0xA will
be among the most commonly seen crashes.
Arguments:
Arg1: 0000000000000081, MmMapLockedPages called without MDL_MAPPING_CAN_FAIL
Arg2: fffffa800b7a5120, MDL address.
Arg3: 000000000000008a, MDL flags.
Arg4: 0000000000000000, 0.
I have an issue with my Latitude D400 laptop which has now occurred twice. Basically, after operating normally and shutting down properly it has stopped booting. After the POST screen it simply hangs at a black screen with a flashing cursor in the top left corner.
Using the recovery console to repair the MBR and boot sector on the HDD has no effect. Neither does a repair installation of Windows XP Pro. The first time it happened I backed up, wiped the disc and started with a fresh installation of XP Pro.
However, it's now happened again. The hard disc is completely undamaged (all files are intact) but will not boot at all.
I have a HP G26 notebook pc, it has windows 7 on it and when I turn it on it only get to the windows start up screen with the little flashing logo and won't boot any further.. I have tried system repair, my back up disks.....
View 6 Replies View RelatedMy laptop won't boot. I press the power button, the power button lights and I hear the system fan run. Then it shuts off and the caps lock LED flashed about 20 times, then turns off if under battery power. If on AC power then the LED stays steady after flashing. Screen never turns on. Late yesterday and late today the computer started hanging. Usually a restart would fix it for a short while. But now it's dead dead. I suspected overheating so I did a bit of digging and figured out how to remove and clean the fan intake. It's was clogged up pretty good, but that hasn't fixed the problem and the laptop is now cool to touch on the bottom..
View 4 Replies View RelatedI'm trying to fix my fathers laptop so he won't have to spend money on a new one. Here's the problem:
When I press the power button to boot the laptop it does not boot, it just flashes the power light(s) on and off at maybe 1 flash per second. I've tried removing the RAM-sticks one and one, removing the HDD, removing the battery and removing the DVD reader (not all at the same time, of course). None of those helped, it still did the same thing.
Then I tried to blind flash the bios from a CD, the laptop comes on with the fan at full blast, the DVD reader comes on and it stays on, but it never finishes and powers off.
I flashed the Bios (from Acer webpage vers. 1.10 to vers 1.13) on my notebook Acer Aspire 8930G - 864G64Bn. No I have a really big problem.
I can switch on my notebook and it shows the Acer empowering people screen, but stay there. Nothing happens. The only thing I can do is press F2 (is the only thing which is offered on the screen) But also there it just says please wait.... and nothing happens.
At the first time reboot after flashing I was able to enter the Bios, but since than I can't.
So I read a lot of using a usb thumb drive or an external floppy drive.
Will this work for my notebook and should I copy just the .FD file on it?
I want to flash my card with an older GTX bios I used to have. But some months ago I installed the unlocked roms...
I still have that rom (gsx) and now I want to burn it on a cd-rom and flash my card with the juan software.
So first I burned Juan's software on a cr-rw (don't close the disk). Afterwards I added my old rom. When I want to flash it and I typ:
nvflash -4 -5 -6 GTX1.rom it says that it can't find the file...
I flashed by BIOS with the R4041M3 so I can install the latest NVidia drivers for Windows 7.
I wanted to enable "Advanced" options with the InsydeH20 hack (which requires EFI boot) - and I kept getting those
"Remove disc or other media" messages.
I thought something went wrong with my USB stick, tried at least 5 of them and finally also tried Windows image itself - with no luck!
Then, I switched back to old BIOS - and the EFI boot worked immediately on the first USB drive!
I got this laptop a few days ago, I currently have 7 and XP installed on it and kind of have vista...(read further down).
My 7 seemed to break today after playing around with a program called powerstrip trying to get my external monitor to show the right resolution (I've realised now the cable vga was broke, but meh) but this is not the full problem, after windows 7 failed to boot I tried to boot xp after turning it off during the windows 7 splash screen and now im stuck with a dash when I turn the laptop on (I dont know if its actully related to something I've done or not).
If I turn the laptop on a flashing dash comes on in the top right, it then stops flashing and turns into a none flashing dash further up the screen and just locks here and I cant do anything at all other than trying to restart it. When I had this problem previously (at least I think this problem) on my desktop it usualy turned out to be something usb related but I have everything unplugged (all though the bluetooth adapter light is on when it is doing this) so I realy dont know what to do...............
What does a Quickly flashing yellow/orange battery light mean?
I bought a replacement battery pcga-BP2E for my sony vaio vgn 417M.It ran off the battery and showed it was charging but % didn't go up. Every time I connect the power cable the battery light flashes rapidly and I can't find in any manual what it means.
Using my original working battery the battery light flashes slowly as it should and the laptop works ok.
10 days and I am still waiting for a relpy from the supplier atleast I started my complaint through paypal.
The notebook is a compaq presario c500.The seconds are not counting in the bios setup screen.Obviously the clock is wrong whenever the pc is turned off and or restarted.I have already replaced the battery(cr2032 3V)twice to make sure it is not that.I also updated the bios.That did not work. What controls the time?
View 4 Replies View RelatedMy HP notebook G7 was doing windows update on monday night it was on all night but in the morning when i checked it had an all blue screen that says HP and a circle that indicates it is loading but nothing else. it stayed like that all tuesday i am guessing it froze. i have tried restarting the computer with the power button but i get the same screen again. i have take out the battery also and the same thing happened.
View 1 Replies View RelatedI get the error in the Title after i tried to flash the latest BIOS update for the Z510. I can press ok and then get into the boot manager but i cant choose anything there. Also I cant boot from a Disk with e.g. XP on it.
I also tried the Inside BIOS crisis mode (fn+r) with the BIOS file on my USB drive but it doesn't work and tries to access the file on the USB drive but boots normally instead to the error again. (Couldn't try it with removed battery as I have to remove the whole back to remove the battery on the Z510).
I ran the diagnostics test as instructed prev and all passed. I then loaded BIOS defaults as instructed and saw "2nd boot priority hard drive" What does this mean and can I fix?
View 15 Replies View RelatedI've been travelling for the last 14 months and couldn't stand using my Asus EEE 901 as my only computer. So I got my beloved XPS M1330 send to me from sweden (where I'm from) a couple of weeks ago.
Everything worked fine when I got it, but quickly installed windows 7 on it (since win 7 wasn't released when I left home).
I did however notice that the CPU usage was always between 10-40%, even when I didn't do anything. It became better when I installed windows 7 but was still unusually high. That didn't really do anything because it was such pleasure using a real computer after a year with a 8,9" netbook as only computer.
[PPROBLEM START]
Approximately 1,5 week after I recived my computer, I was surfing the web as usual, when I suddenly noticed a spot in the middle of the screen. I tried to scroll to see if it was some dirt on the screen but it followed the scroll.
A couple of second later the screen got colored horizontal lines and after another couple of seconds the screen looked like this:
I got completely terrified, and the happiness i had for my "new" computer quickly turned into a horror movie.
I had to hold the power button to turn it off and after a couple of minutes I started it again. Bios loading looked fine but the screen froze at the Windows loading bars with some colored lines in the middle. Had to hold power to turn it off, and haven't dared to start it again since.
Is it my graphics card (8400 GS 128MB) that has died, or is it the motherboard which is causing the problem?
And are there any chances that I somehow can fix it?
I bought my XPS M1330 the 28th of December 2007 (2 years and 4,5 months ago), is it still covered by any warranty? Because it is obviously not a user caused problem.