When I try to rip a CD, I'm getting some very slow rip speeds. Here's what I'm using:
Windows 7
Winamp Pro 5.571 & Windows Media Player 12
Sony Vaio Intel® Core™ 2 Duo P7450 (2.13GHz)with Intel® Centrino® processor with Blu-ray Disc(which seems to be a Pioneer BD?), 4GB RAM.
Lame version seems to be 3.98
I have a problem with my Combo device (TSSTcorp) on my Dell Inspiron. When I burn a DVD data disk with Nero it is burned at 1X to 1.2X. It doesn't matter which speed I have set (4X or 8X). So it takes approximately 50 minutes to burn a full DVD and after that the verification takes same time at this speed again.
When I burn a CD the real speed is again slower than the speed I have chosen. And at the end of the burning process I get a message saying that "buffer underrun error has been avoided hundreds of times" or something like this.
I have dell vostro 3350 i7, 8GB RAM, 750 GB Hard Laptop. No additional software. But booting time and speed very slow.
View 1 Replies View RelatedThis is terrible, by using CPUz i can see that, whilst the laptop is charging, the clock speed drops down to 900mhz and fluctautes between that and 1400mhz, this is shocking, i can hardly watch youtube videos or even post this thread, the lag and slowness is unbearable. When running on battery power the CPU speed shoots up to 2500mhz and stays there,it never seems to go to its turbo speed either. Whilst charging, the laptop is unusabe, i cannot do anything on it.
View 9 Replies View RelatedFirst of all I have a dead pixel right in the middle of the screen - will be taking this up with Dell tommorrow as its really off putting especially on brand new laptop.
My second issue is with wireless - did have problems initially with wireless disconnects and genrally slow speeds
Im not entirely sure but removing Mcafee seemed to work with the disconnects at least - load of rubbish imo
Now my only other major issue is with wireless speeds on the 1703 card
I seem to max out at about 45mb on all broadband speed tests - while on another laptop I get the full speeds of 80mb on the same server at the same location
Im only getting a link speed of 72Mbps in the networking tab of Task Manager and this does seem rather slow - the other laptop gets 450Mbps (better wireless card - to go with my Asus N66U Router)
Anyway my thought process is that the 1703Â wireless card is not up to much - I understand that the 1703 card is wireless and bluetooth - with I think 1 antenna for bluetooth and one for wireless connected to the wireless card.
Now I dont use bluetooth much if at all - so does it make sense to buy just a wireless card and connect the two antennas to the card and therefore losing bluetooth connectivity but gaining better wireless connection
I think I have an Intel Centrino WiFi Ultimate N 6300 in the other laptop
I've got an HP Pavilion g6-2260sh notebook with Windows 8.1 Pro operating system. My problem is that the internet download speed had fallen from 80 Mbits to 3-4 Mbits. The upload speed stayed the same as before, 25 Mbits. My notebook is connected to a router with another notebook and a PC. Those 2 computers have excellent internet speeds. I've reinstalled the operating system, but the issue still persists. After the reinstallation, the speed was fine for maybe an hour and then it dropped to 3-4. I only installed drivers from the hp driver finder, nothing else. I've tried the connection with cable and wi-fi with the same results. The device manager shows 1 Unknown device and 1 missing driver for Ralink_RT3290_Bluetooth_01
View 3 Replies View RelatedHad a w540 for a few days and so far it'd be fine. At the weekend i used the laptop on battery for a long time and thus set the power-management low to conserve power.
However, today having switched back to power supply and setting power scheme to max performance the CPU is still concerving power.
Â
Its running (according to resource manager) at 29% and no matter how much i do it sticks at that percentage. The laptop does feel like its running at that clock speed too ... everything is super slow ... can watch programs drawing in the display...
Ive had a vaio Z 2.53Ghz for a few months working very well. Lately Ive been noticing that the system feels really slow. I just ran a CPUZ and got the readings that the CPU is operating at 1/2 speed (around 1.26Ghz). I ran a few benchmarks (SySoft Sandra/Everest) and was confirmed again that the system is running at 1/2 speed. I remember that runnig on batteries usually the CPU slows (lower CPU multiplier) down to conserve batteries but mine is plugged-in and it does not make any difference. I opened it up and took out the CMOS battery for a few seconds to re-set the BIOS to see if that would fix it. Same problem.
Also I noticed that my power settings Tab incontrol panel are all grayed out so I cannot change or access them... this is all so weird... I know that setting power settings in XP's to the maximum performance profile, turn off Intel SpeedStep which is what I suppose is forcing my system to permanently using a lower multiplier...
I have Compaq Presario CQ42-273TU NBPC. Â In my laptop , if i play video , it becomes very slow. After video becomes slow, everything else on the laptop becomes slow. recently i gave laptop for service also, then also i have issue with video.
View 8 Replies View RelatedOn my brand new Sony SR590, I cannot get the ethernet connection to run at 10/100/1000, only at 10/100. I don't see any settings for this whatsoever and I think I've looked everywhere. I have the Yukon 88e8040 card. When I bought the computer, the site says it's a GbE card! But why isn't it running at such speed?
View 8 Replies View RelatedI've been having a few problems with my sony Sr. When I was carrying it around in school in a nicely padded case, I had a couple "unexpected shutdowns". I have no idea what causes these, but does anyone have any ideas? Also, is there any way to prevent this? I'm not very rough on my laptop, although it might be bumped a little from outside the bag.
Also, on two occasions, the laptop started up from sleep inside the bag unintentionally.
It heated up a lot inside the bag, although it's not what I would consider an overheat, because I had no slow-downs, crashes, or shutdowns. However, after the second time this happened, my fan has been going very fast and cycling between very fast and fast speeds, much faster than normal. This is happening even hours after I shut it down for 12 hours and let it cool off. Is there a solution for this problem, and could there have been some sort of damage?
One more quick thing: the little tube things connected on top of the power switch and power cord connector wiggle when pushed. Is this normal?
how can i change my speed of fan on my sony vaio FW laptop, any programs i can use.
View 9 Replies View RelatedWhile eagerly scouting the Zs, I've greatly enjoyed this forum for the past few weeks. I've been stopping by (ok stalking) my local Sony Style store to check them out in person, and became curious about a discrepancy.
Does anyone know off hand if there is an inherent memory speed or bandwidth difference between the 520m and 540m (or 620m)? I haven't noticed anything official from Intel or the Sony specs, other than they all use DDR3/1066 sticks.
Last week I snapped a picture (rather fuzzy cellphone, sorry) of the WEI screen for the lone silver GX/S (i5-520m) floor model. It shows a lagging score of 5.9 on memory, which doesn't jive with other performance scores mentioned on this forum (that I could find).....
Does anyone know the speed of the SD card reader on Vaio TT? I am planning to run the Windows 7 from the HDD; and run Ubuntu from the flash card that I will be putting on that reader
View 10 Replies View RelatedI just received my z690 cto and I'm doing all the tests I can think of to check that everything is working properly.
I have one question about the memory.
I ordered it with 4GB ddr3 working at 1066Mhz and when I run the program cpuz the memory is recognized as DDR3 PC3-8500F but the "DRAM Frequency" is reported as 532 Mhz (instead of 1066).
Can anyone tell me if it is normal or if it should report 1066?
I ordered a FW490 CTO w/ P8700, 4650 1GB, 4GB RAM, Vista 64, etc. Anyways, I was a little disappointed with how well it ran Americas Army 3. I downloaded and ran GPUZ, and I got some interesting results... It says that my 4650 uses GDDR3 memory, which is apparently the best setup for the card, but it also reports that my clock speed is 450 MHz, and my memory clock speed is 600 MHz. From everything I have gathered, that is below what most 4650 Mobilitys are at... what gives? What are the speeds of everyone elses 4650?
View 10 Replies View RelatedI recently replaced the fan on my VGN-SZ360P. It was hell, I had to remove everything just to get to it. After a few hours I was able to piece everything back together. Now my Speed switch doesn't work. I need the Speed switch to use the DVI port on my port replicator to out to my external monitor. Seems like it is stuck on Stamina mode. In order to use the DVI port I need to be in Speed mode and with the nVidia graphics card. I tried to uninstall and reinstall everything. Nothing seems to work. I contact Sony and the tech told me to do a system restore. That is going to wipe out my entire computer to factory default.
View 10 Replies View RelatedI can run in safe mode and in stamina mode all day long, however when I switch to Speed mode after a few secs the screen goes black and the notebook just turns off. Anyone have any ideas? I am at a total loss. I have tried a complete restore and also tried Natius drivers.
View 7 Replies View RelatedI've just purchased a VAIO CW2 (VPCCW2S1E) and did a format and fresh install of Windows 7 x64 to rid myself of all the bloatware. The problem is that copying to, from and between external USB flash/harddrives is now extremely slow - often a couple of hundred kb/s, and sometimes 2-3 Mb/s, when the speed should be 20 Mb/s+. I've had the drives for a while and they work flawlessly over USB 2.0 with other computers. I know that USB copying speed was normal before the format as I copied the Windowsdrivers folder to a USB harddrive, though that folder was only a few hundred Mb.
I assume I missed installing some USB chipset driver after the format, though I have installed the following:
1. IPS_Driver_1.0_10Q1_O_1.0.0.1030 (unsure what this is)
2. SATA_Driver_Intel_Non-RAID_8.9X64_E_8.9.4.1004
3. SFEP_Driver_Sony_8.0_10Q1_O_7_8.0.1.1 (unsure what this is)
The list of available drivers is here: [url]
I've installed Windows 7 on a fair number of computers and never had this problem; how typical then that it should happen on my own laptop
Updated to windows 7 on my FW and it's definitely slower at booting up than vista. Vista was probably under 50 seconds and
it was fully usable after these 50 seconds. Now, in windows 7 it takes over 2 minutes for it to be fully usable.
I just got a new VGN-NW230 and the wireless seems very slow and has had problems connecting at times. The laptop has an Atheros AR9285 (it's N and the specs say it's 150 Mbps capable) and my router is a Netgear WNDR3700. I've updated the drivers on the Atheros and the router firmware is up-to-date.
The card only reports connecting at 65 Mbps. I have another laptop with an Intel 5100 card and it connects anywhere between 150-300 Mbps. For a "real world" test, I compared the speeds on speedtest.net. The Atheros (Sony) is getting at most 1.5 Mbps down, while the laptop with the Intel 5100 gets 17 Mbps down
Well, this morning working in the TZ wasn't at all the same..even the most simple task like opening the control panel it makes for ever...Is very strange, just from today! It doesn't even open some things as disk defragmenter, is incredibly slow, what can I do?
I checked the task manager, the processes are 64 but the strange is that the CPU Usage is stuck to 100%..
I love the Vaio P, but on every page I read that the Vaio P is slow. But what does everbody mean by slow and compared to what?
I have a Compaq Pressario
1.6ghz Intel Celeron
520 CPU
1024mb memory
256 shared intel graphic card (mobile intel 945 express chipset family)
It is running Windows Vista home basic.
So my question is; will the vaio P run slower than my compaq model? And in what? opening programms, etc.?
I own the VPCCW27FX from Best Buy. Last night, after burning a DVD, I experienced the blue screen of death. I noticed that my DVD writer only burns at 2.4x speed. I called Sony Customer Support and they could not provide me the with the optical speed of my drive and could not help me increase my burning speed. To the other people who own this computer or a similar model, what is your drive speed? Is there something wrong with my computer? It takes me 23 minutes to burn a DVD, a lot slower than my old Toshiba laptop.
View 9 Replies View RelatedIt seems for some reason my Z690 does not work well in the speed setting. This results into videos that seem to refresh a lot, games that are slow and have jagged edges and in general slow video performance.
Whats funny is that on stamina setting, all my graphics actually do quite well. Videos play fine as do the games /w smooth edges
I have a Vaio Z, model is VGN-Z12GN.
I upgraded from the pre-installed Windows Vista to Windows 7 Professional (new, up-to-date legit copy from MSDNAA, no pre-release version).
When I am in Speed mode, I can not adjust the screen brightness by using Fn+F5 and Fn+F6. I really would like to have this functionality back again .....
Does any else have this feature working under Windows 7?
I have everything functioning (incl. FN brightness and volume controls) in my partitioned install except this.
I have the switch itself set to "Stamina" but neither mode even brings up the little green light beside it. It is completely unresponsive.
I tried to copy data from one hard drive to another, and a little notice came up saying I would be better using a high speed port. I was cleaning out my closet yesterday, and noticed on my FZ box it says it comes with 3 high speed ports, but only two show in device manager, which are the two on the right side, as the drive I was transferring from was plugged into the one on the left.
View 8 Replies View RelatedI have a VAIO VGN-SZ55GN but I found out that I can't switch between speed/stamina mode.
I had had the intel graphic driver installed automatically after I'd installed a new OS onto the laptop but I can't get the nVidia driver to work.
I tried shutting down the laptop, moved the switch to speed and turned on the laptop again but I still can't get the laptop started up w/ nVidia graphic card.
Have a Vaio Z112 with the Nvidia 330M. I know this gpu should slow down to ~150mhz when only running 2D apps. Looking at nvidia system tools and nvidia precision tool mine always seems to run at the full 475mhz regardless of what I'm using.
Anyone else experience this? Did Sony write out the slow speeds in their drivers due to the assumption we would switch to intel graphics when needed?
In nvidia system tools there is an area that shows 2d/3d clock speed. normally you would expect to see ~150/475 there...I only see 475. Basically it looks like there is no 2d-only clock speed.