I was trying to play a video and the computer froze. I waited several minutes and nothing responded. I finally had to hold the power button to shut it down. Now it will not go to the bios screen and the screen shows a bit of brightening but does not go anywhere.
I've googled for a solution and there are several pieces of possible solutions I have found but as is too often the case, there were no follow up answers to make the posts helpful or, the answers came tantalizingly close like the following for a similar problem with an acer aspire 5315:
"1. first download the attached zip file and unzip it.
2. burn the extracted disc image to disc using nero.
3. place the newly burned cd into your laptop cd drive tray
4. remove the battery and power cord.
5. press and hold FN and ESC keep pressed and insert power cord and then press the power on button
6. your notebook should power up but without any display.
7. you should see the cd/dvd drive activity light blinking as it reads from the recovery disc.
8. if all is well your laptop should power itself down after about 2 minutes
9. once it has powered down remove the power cord and wait about five minutes.
10. finally insert your battery and power cord and power up your laptop in the normal way............
My Windows 8 install got corrupted and will not boot. So I just want to get the laptop to boot onto the recovery DVD or any DVD so I can rebuild it.
No matter how hard I press F2 nothing happens and I keep getting "No Bootable Device, Hit any key." This just takes me into an empty boot menu! I have tried with what I know to be bootable CD/DVD in the internal and have used external DVD drives.
I just want to get into the setup to boot onto the DVD drive.
I have a 9300 that developed the single-pixel wide vertical line about a week ago. Dell has agreed to replace it but will only do so if I send the entire computer, minus the HDD and battery, to the depot.
The problem is that I installed a 7800GTX using the hacked XPS2 BIOS. The rep specifically stated that the depot checks the entire system "for issues". The hacked BIOS and officially unsupported video card would be very easy excuses for Dell to refuse to replace the panel, even though I did the swap 3 years ago and the system has been fine up until last week.
i turned my new travelmate 8471 into a brick by flashing it with the wrong bios (shame on me ) - now i am looking for a way to bring it to life again - any suggestions? Its really bad that it happened 3 days after i got it and i have no idea because these models are quite new to the market - acer support also didnt give feedback yet -
I flashed the BIOS using the windows software beyond my better judgement and the install crashed. I waited 30 minutes and the system never started to flash again. I have tried a few ideas to get the BIOS to restore. I tried the FN-ESC method and the usb-Floppy tries to install the system but i am still not able to get the OLD BIOS restore.
I have the BIOS backed up on the systems hard drive but I am gonna have to remove the drive and get the backup BIOS and try to install it on the recovery disc. What are some ways to restore the BIOS the system is also out of warrenty and I payed acer support to tell me that are not able to help me.
My Windows 8 install got corrupted and will not boot. So I just want to get the laptop to boot onto the recovery DVD or any DVD so I can rebuild it.
No matter how hard I press F2 nothing happens and I keep getting "No Bootable Device, Hit any key." This just takes me into an empty boot menu! I have tried with what I know to be bootable CD/DVD in the internal and have used external DVD drives.
I just want to get into the setup to boot onto the DVD drive. How difficult can that be!
this is my first post so a quick hi to all of you and thankyou for many solutions in the past which have spanned from this forum.
Well i have had to bite the bullet and register so i can ask you guys for help...the story goes...
Ok i receive a laptop Dell Inspiron 9300 from a friend who has dropped it (well he says the kid knocked it off the couch and then to add insult to injury he followed it over and landed on it) well needless to say i diagnosed that the motherboard had failed as i ran the system from a barbones state to rule out any hardware failures. So i ordered a replacement board from the big old bad Ebay guy that hangs around the internet...So i rebuild the laptop plug it all in and turn it on.. so far so good i see the Dell logo and select to enter the bios to which i see "entering setup"... now instead of going into the setup i receive only this... "The ac power adapter cannot be determined. The system can only boot with a 130w power adapter or greater" .....
I have an ACER Aspire 5520, (model ICW50) with AMD Turion TK55. I tried to upgrade it with the BIOS available under the model's specified page in ACER site, version 1.33 (IC50133.WPH).
Unfortunately I was naive enough to try flash32.exe, which is the windows base version of the flashing program; now I have a dead BIOS. Windows froze completely, I had to unplug and disconnect battery to have it down, and it never came up.
Then I did a lot of research and I found and browsed hundreds of pages about Crisis Recovery Mode (CRM). From all I read there are some misconceptions I want to get past:
1 - Deal with different CRM versions, which get accessed by Fn+B, or Winkey+B; on my case I have found that CRM gets accessed with Fn+Esc. I know it, because instead of powering up and then dying in 3 or 4 seconds on an eternal loop, when I press and hold Fn+Esc and then I connect the power adapter (with battery disconnected), I get a quick orange flash under the power button. So, when I press the power button the computer keeps running, fan is running, and it is checking HD and CD-ROM drives.
2 - There is a lot of myth about the way one has to press and hold Fn+Esc. You just have to press it before you connect the power cable. As long as you get the quick orange flash under the power button, you know the PC is in CRM. I have done all the fancy combinations of holding those keys down, but it all ends up in the same. By the way, even if you connect the battery, instead of the power adapter, once you are holding Fn+Esc it gives the same result: orange flash, you are in CRM. Of course you do not want to flash it using the battery, that's why the emphasis on connecting the power adaptor instead.
3 - Most of the info I found about this matter then turns to building the Crisis Recovery Disk (a floppy) or a CR pendrive. It does not solve my problem because when in CRM, the computer completely ignores the USB ports, the 4 of them, I tried one by one, be it with 2 different kinds of USB floppy drives, or pendrives duly formatted in FAT. There is no blinking of light on either. There is no attempt at all to access any of the USB ports......................
Few days ago I tried to update the bios and something went wrong. Now my Timeline 5810T is piece of hi-tech scrap.
I tried many ways to recover bios with Fn+Esc tricks using CD and usb flash with sort of different filenames (BIOS.WPH, jm31x64.fd, ICL50HW.fd, ...), but i'm not happy yet.
It seems, that the old finesses doesn't work with x810 Timeline series with Insyde bios inside. After many hours with uncle Google, it seems that nobody on the planet know the right way.
reset BIOS admin password on my HP Pavilion tx2500 - I didn't use it for more than one year so the password is obviously forgotten. After 3 invalid attempts it displays "System disable Key: 72015992".
The uefi bios recovery does not work on my computer nether has the .exe files that are bios... I would like to try flashing the BIOS but don't know where to go...
One morning, laptop powers-on (Blue led on power button and on front bezel), no display, fans spin up and down, CD drive makes the usual seek sound. Attached external screen from my desktop, no display either, no POST!!. Removed HD, RAM, NIC, no change. No beeping what so ever, really looks like the notorious Acer BSOD i've read about. What I need is the EXACT name I should rename the BIOS file (JE70D118.ROM) to be able to use the Phoenix BIOS recovery function (FN+ESC+PWR) with the BIOS file on a USB key or SD card. Seems to be a national secret or something... Acer does not seem to have this documented anywhere.... including the actual BIOS recovery procedure....
I changed my HP to boot with legacy CSM, but I couldn't boot from the Windows 7 boot disc. The laptop was shipped with Windows 8 configured for UEFI boot before my change. The screen after boot is blank and now I can't even get to the bios menu.
I have tried a Windows 8 USB recovery drive, but the computer doesn't seem to try to boot from flash, even with the hard drive disconnected and the CD tray open.
I watched a video of a man disassembling an HP Pavilion completely down to the base plate, but I did not see a back-up or RTC battery anywhere in the computer. If I could find the bios back-up battery for removal or reset the bios somehow with the hardware, i would do that. I waited for 4 hours without the main battery attached without any change. At this point I don't know if this model Pavilion even has backup battery. How to reset the bios to default UEFI setting without a bios menu? Note that pushing F2/F8/F9/F10/F11 and a whole bunch of other keys does not bring up the bios menu at boot time (like it did when it was in UEFI mode).
My next steps are to use the HP Recovery Media application on a 2nd computer to create 6 Window 8 DVDs and see if these will boot from the CD. If that doesn't work, I'll contact HP support and see if they can send me a custom recovery disc.
It seems strange to me that I can't even get to a bios menu in legacy mode. Is this normal? I suspect that my configuration change corrupted something and no booting will work any more. If booting from disc doesn't work, I think I'm stuck with trying to drain whatever back-up power source keeps the bios in-state, however long that is.
My 9300 just stopped working and the power supply blinks when plugged in to the laptop but is constant when not connected to the laptop. I'm thinking it's not the power supply because of this.
I have trier removing the battery, holding in the power for 30 seconds, powering up with the battery out etc. I'm don't think it is the battery either
I have also searched the forum but can't find anything that is similar. I did see a page on the net that said it may be a short on the motherboard but it was talking about dells.
It is sitting beside my bed and last night every 10 seconds it made 4 light clicking sounds that lasted in total about 1 second.
Not a bad notebook, with 4 gbs of memory. Fair warning to all owners. 4 gb's of memory is sweet only problem is that the newest bios version(1.20) will not support lil know boot into bio's. If you are planning to upgrade your memory make sure you have bios version 1.19 installed. Or your system will not boot. Not only does version 1.20 not support the 4 gb's , it also drops the max memory setting for your video to 128. ( versus 256 mb in ver 1.19). After installing yor memory make sure to d/l SP1 for vista. It may not use all the available memory but it will at least show 4 gb's in windows..
Today my speakers on my laptop started cracking so I plugged in the headphones to see if it made the same noises with them and it did so I figured it was just a driver problem.
I reinstalled the Realtek HD driver twice but I still have the same problem. The speakers worked fine this morning but after moving home from university this afternoon they've started cracking.
I have a 1 year and 10 month old Acer Aspire 9300 laptop and the motherboard recently bit the dust. My retailer in Gananoque Ontario could not find a replacement. I called Acer which took forever to get to someplace where I could leave a message. I received no reply. After you've called once it's impossible to call again. I guess their answering machine recognizes my phone number and then asks questions that makes it impossible to get through. I sent a detailed explanation of my problem by email 3 times asking a few simple questions, the most important being 1) where can I send the laptop to be repaired? 2) do you sell replacement motherboards and if so how can I buy one? Am I asking too much or getting too technical for them? I've been trying for several weeks now to contact Acer to no avail. What kind of an idiot company is this? A techie put me onto a company called Grand Tech in Richmond Hill Ontario that can replace the motherboard on an exchange basis but the replacement will likely be a repaired one.
Someone told me that the problem I have with the motherboard is common and it is because the solder used at least when mine was made was of poor quality. I hope that problem has been resolved. I'm afraid a repaired replacement my have the same problem. Some people just say to trash it and get a new on which I did. I bought a Dell Inspiron 17 which is supposed to arrive on Nov 11. I would however like to repair the Acer if it can be done cheaply and use it to replace my 8 year old PC in the rec room.
my acer aspire 9300 switched off on me tonight, the power button lights up and i can feel air from the side heat exhaust, but nothing eles,and the same thing happens just on battery without the power lead plugged in.
I have an Acer Aspire 7720G which has a Nvidia GeForce 9300M G 256MB graphics card.
Other specs - Core 2 Duo T5750 (2.0 Ghz), 3Gb Ram 667MHz
I've installed a clean version of Vista Ultimate but it doesn't recognise that there's a graphics card present. I've tried to instal the drivers from the Nvidia website but it aborts because it can't find the hardware.
I've also tried installing Vista SP1 but still no avail.
ive just finished setting up my new acer ES1-512, And was about to make my recovery media through the acer console in windows 8.1, and the program will not open ? i get to the part where it wants me to allow the program to make changes, but then nothing happens ? i have tried going to the file location its self to to start the program but this makes no difference, ive looked all over acers site to see if i can re-download the console but have found nothing?
I had to upgrade my BIOS to the latest one but I found out that I was viewing a different model. Now when I bootup my laptop, all I see is a black screen with a flashing white line.
How can I recover from this error? I've been trying out several "Crisis Recovery Methods" but they don't work. I've used all key combos for boot-block but only Winkey+B makes three beeps. Maybe I'm doing something wrong? I put the right BIOS.wph in there too. I also did a CMOS reset and nothing happened. I bought a $41.99 external usb floppy drive because of this!
I've been following the thread below, but so far have not found the key to recovering from a failed BIOS update on my dv6500t laptop:
CQ45- Insyde BIOS RECOVERY using a USB THUMBDRIVE
I can press Windows-B upon bootup and I hear a single beep followed by the USB floppy spinning up briefly. Note that if I turn on the computer without pressing those keys there is no activity or sound, so I think I'm on the right path towards a BIOS recovery.
The problem is (I believe), I don't know what filename the recovery process is looking for.
I've tried: BIOS.BIN, BIOS.ROM, BIOS.WPF Also: 30CC.WPH, 30CC.BIN, 30CC.ROM, as well as 30CCF58.WPH.
I've tried this process with a USB flash drive and an SD card, but only the USB floppy drive gives me the feedback that file activity is actually happening (this means that I don't have enough disk space to try 50 copies of the same file with different name combinations).
How to get into the Bios of a Pavillion G6 laptop that has got a password protecting it. After 3 attempts I get the system disabled, it gave me a code 71690505 ....
