I have problem with dv9700t and bios F.59A. After upgrade bios from F.58 to F.59A and reboot, notebook won't start - there is only beep: first beep is long and other two are short. For me this sound show that is problem with graphic card. But from years notebook work fine and i don't use it to play games (only for office work).
So what can i do to run again my notebook?
How can I recover from a failed bios update? Is there a way to return the computer to the previous bios configuration?
View 3 Replies View RelatedI've had a HP Envy 15 touchsmart laptop (Windows 8 originally, windows 8.1 now) for about 2 months now and haven't had any problems, till a few hours ago i attempted to update the bios of my laptop using the hp support assistant. After the restart, the pc would no longer start up and took me to a blue screen with the error message SYSTEM_THREAD_EXCEPTION_NOT_HANDLED. Everything I have done so far short of a refresh or reset has not worked and if i could I would like to avoid both as I do not have the bandwith to go download windows 8.1 again.
View 3 Replies View RelatedI've recently gotten my whole system board replaced by HP repair because my 8600m gs failed after 1 year of use. Is there any way I could underclock my GPU? The idle temps seem pretty high (50c!). Are there any other ways to cool it down or to make the life the GPU longer? Are the replacment GPU's also faulty?
View 3 Replies View RelatedThis machine was not dropped or damaged in any manner to cause this. Last couple of weeks when I open the LCD lid past 90 degrees upright, the LCD screen letters of words turn fuzzy and page colors change.
For example, if I push gently back on the LCD lid of my right now as I type here on this forum page, the white background of this web page turns 2 shades of pink with what looks like large square-like pink pixels. When I let up on the pressure, and the screen returns forward to 85 degress upright, the LCD screen colors of this web page go back to normal -- white is white and the image is sharp.
It is the entire page -- no pressure spots or issue limited to around the edges, its the whole screen that is affected.
LCD going bad or something else? This is definitely related to the angle of the lid and the issue is both position and pressure sensitive.
My dv9843cl will not start, refusing to even go into BIOS, even though the screen turns on. This is suspiciously similar to what happened to my last laptop, and I suspect that a faulty graphics chip is at fault. I was playing Team Fortress 2 shortly before it crashed, and it was performing poorly, and occasionally making random colored boxes or random interference appear on the screen.
Unlike my last laptop, however, I'm not sure if there was a recall for the graphics chip, and since I bought the laptop in 2008 from Costco without anything other than the standard warranty, I'm probably not eligible for free repairs, right? -_-
Does anyone try to update his BIOS to F.2D version?
Is it safe to update from windows since it is winflash?
Any one BIOS update known to be better than the rest?
I am reading a good deal on the boards, and people like F.16, but I don't know which would work best in my situation. My main issue is being able to see the 3.12 GB of RAM after I put 2 2GB sticks in.
I have XP MCE , T7200 which came with the DV6000T bought in Jan 07.
I just want it to run cooler and faster, so far it has been a workhorse.
Which would be the best choice? [url]
HP has posted a BIOS update on their website for the DV6-2190US laptop. The update is listed as F.1AA and claims to "improve system fan behavior". This laptop has a quad core I7, 720 QM clarksfield processor so anything to better control heat would be good to consider. I am usually never hesitiant to update a BIOS, even on the numerous laptops I have owned, but....I have noticed HP had some of their BIOS updates bricking their laptop lately.
Has anyone flashed their DV6-2190 with this update yet?
Hp update popped up on my DV5t-1000 and asked me if I want to update the bios version. I downloaded it, but while the installation an error occurred and it dumped all the memory to the hard drive. After a restart, it does not even show the hp logo only a black screen. All the led lights are on not blinking.
View 10 Replies View RelatedI thought it was a good idea to update my BIOS from F0.A to F17.
I am now stuck with the fan constant running and I have checked some other threads and found that you can switch this off in the BIOS.
I have checked and it is already switched off!
I tried to restore to go back to the old BIOS but it seems I am f****d. Not possible.
Are there tricks to go back to the original firmware.
Are there third party software that can stop the fan turning all the time.
This what I installed to my HPDV4T 1020us
[url]
My computer shutoff and when I turned it back on, the screen stays black.
I was updating my Bios as described on Hp website and now it seem's that my dragon is dead.
Laptop is powered on but nothoing happening at all. Is there any Bios recovery soft or bios recovery mode to try ?
I have a HP Pavilion dv4t-1000 CTO Entertainment Notebook PC and after updating my bios from F.22 to F.24 the computer wont boot into Vista. It was completed successfully using the winflash, but the computer restarted it just stays at a black screen, and wont go any further. (I hope bios is not corrupted.)
The computer is on but its not booting the operating system.
Is there any way I can revert to the old bios?
Also is there any key combination that can get it to load BIOS from a USB flash drive?
My troubles are as follows:
I started working on a presario v6130us laptop with a blue screen. The owner thought it was due to a virus when she opened a email. I went and wiped the HD and reinstalled windows XP pro. Had the darn thing working nicely.
Then I thought he computer was running a lil slow, so I decide to update the bios. From (I believe) v.07 to ver.29 from the hp website. At the restart, it never restarted, so I restarted it by pressing power button. Went into the same ol blue screen loop. The stop message is 0x0000007b. I looked that variable up on the microsoft webpage. It says it is a Win 2000 unmountable boot device. Prior to this message it was Stop 0x000000ED.
Does anyone know how to roll the bios back, or what could be causing this problem? I have done a quick HD test. so far it has passed and is now doing the "executing" test @ 20% complete. B4 the bios update, the test would say FAIL 1- 07.
Bios password not working- system disabled code 70724054
View 3 Replies View Relatedi have a compaq presario CQ42 . today i has disassembling my laptop and applying thermal paste on cpu and gpu . so , the problem is when i play games about 5min or 10min my laptop suddenly go on sleep and shutdown itself then i try to restart it and after that i get this message"The system bios has detected your notebook PC was placed in hibernation to avoid overheating .The system is now operating normally and your data should remain intact. Overheating may occur if the cooling vents are blocked or the operating temperature exceed the specification. The notebook PC should return to normal operation once the situation is resolved.
View 9 Replies View RelatedI've got ap HP Pavilion dv6 - 3000so. When I try to start it. There comes a blue warning and it sayes: Enter Administrator Password or Power on Password! I try different passwords form the machine, but the new tekst is Invalid Password! After 3 wrong passwords a new tekst comes up: System Disabled and Key: 50118153!
What can i do to start my computer?
My 8510W won't start. It starts over and over and I cannot start it in Safe Mode.
I think my harddrive is dead. Am I right?
It is a 500Gb WD Scorpio Blue. Can I replace it with a 1TB disk?
I just get to a screen showing the HP logo...the computer tries to self diagnose but never gets anywhere. Just stays locked. I've had this computer for almost a year with zero issue. Suddenly this.
View 7 Replies View RelatedAfter putting the power on, nothing happen. It gives some kind of blue background. But it's not the critical error blue screen. It's some kind of windows-bitmap.
Using Esc and F2 I could do a System Test. The Short DST (don't know what that means...) says: FAILED.....
It gives details on the FAILURE ID : 64SP28-5HB7AC-XD003F-60VF03.... What should I do next?
The notebook is a HP, model DV6-3160SD, Running W7 on it. Don't know the bit-version (and can not check it).....
My HP notebook G7 was doing windows update on monday night it was on all night but in the morning when i checked it had an all blue screen that says HP and a circle that indicates it is loading but nothing else. it stayed like that all tuesday i am guessing it froze. i have tried restarting the computer with the power button but i get the same screen again. i have take out the battery also and the same thing happened.
View 1 Replies View RelatedToday, somebody (without my permission) updated my laptop from windows 8.0 to 8.1. Later I found out that this person didn't make the, according to the HP supportpage, necessary preparations. HP warns that my laptop now can get problems, like a blank screen, loss of internet connectivity and disabled hardwaredevices. I bought my laptop about 1 year ago. It's a HP Pavilion 15 Notebook PC 64-bit.
View 3 Replies View RelatedYesterday my brand-new VPCZ11X5E completed an automatic windows update, and shut down after completing the installation procedure. Since then windows will not start up properly: it stays in the start up phase (you know, with the windows 7 logo), before the log-on screen.
or should i just do a re-install (=losing some important documents).
I have upgraded my Win 7 operating system to Win 8.1. on my Dell Inspiron NS5050. All other components remain the same. The first deals with the USB Port. I insert a USB and it is not recognized. I open Device Manager and in Properties uninstall the the Driver and reboot. The USB now works correctly. Why does this keep happening? Tried to update Driver but comes back device is up to date. When USB fails I get message, "Windows has stopped this device because it has reported problems. (Code 43)".
Second Issue. Monitor won't start after any updates. After several times starting and restarting, I connected to an external monitor. External monitor starts and I can Log In. Computer functions normally with external monitor. Device Manager one time showed an error with the monitor. I deleted the driver and the original monitor worked correctly. Other times with a simple "Windows Defender" update monitor won't start. Using external monitor works every time. Additional monitor switching sometimes works other times not. Not sure what is wrong with the F1 key. Turns on and off monitor?
I have an Acer Liquid Z200. I've just made the latest update I was asked. Everything was OK but after the update, I had to restart the phone and then... it was stuck on the Acer logo. I tried resetting to factory default by pressing the power + volume keys, choosed "Recovery Mode", then "Wipe data/factory reset" then I rebooted the system but... it's still stuck on the Acer logo and I've tried many times and waited almost 30 minutes with this Acer logo screen... What can I do ?
View 2 Replies View RelatedI have an HP Pavilion DV6 Notebook PC. The other day, it crashed and gave a blue screen error. Since then, it wont start. Ive tried starting it normally and in safe mode, neither work. This is the information given in the blue screen.:
win32k.sys
PAGE_FAULT_IN_NONPAGED_AREA
Technical Information:
***STOP: 0x00000050 (0xFFFFF901C066263C, 0X0000000000000000, 0xFFFFF9600006CCA3, 0x0000000000000005)
*** win32k.sys - Address FFFFF9600006CCA3 base at FFFFF96000000000, Datestamp 53c5df64
When it first crashed, I was playing a game, then the screen got all pixelated, then the blue screen. The computer has had overheating problems because the fan doesn't work 100%. It would shut off often from overheating, but I cleaned the vents out thoroughly, and it hasn't overheated since then. Since the computer wont start, I cant get to the crash dump files.
System update Lenovo stopped working some days ago. Today I had my fingers crossed that maybe with the installation of currently latest version it will work (systemupdate506-11-04-2014.exe). When I have ran the installation it has warned me there are some previous versions and it will be installed, but installation didn't went thru. After manually removing System update service (sc delete SERVICENAME) and running the installation again, the installation wizard completed successfully...
But then when I run System update I receive an error "T440S - System update Cuuldn't start properly".
How to achieve that System update would work properly on T440s laptop. My operating system is 8.1 x64 enterprise.
Running Windows 8.1 for some time, but latest updates (8/13/14) cause the problem. Restore point and shutting down updates allows use, but it's a short term fix.Which update causes the paroblem?
View 7 Replies View RelatedI have a problem with my HP Pavilion 15 Notebook PC, model 15-e055st, which I purchased two months ago with Windows 8 pre-installed. I susequently upgraded the operating system to Windows 8.1 and all seemed to work OK. I then used the HP Support Assistant to do some important updates, which included the BIOS and other software. Following the HP update the computer would not Shut Down or Sleep, but Restart worked OK. When I attempt to Shut Down or Sleep, the screen goes black but the power light and the wifi light on the keyboard remain on and the fan is still operating. The machine will not recover from this situation without me first doing a hard reset by keeping the power button pressed for about five seconds.
I trıed restoring the software to the condition prior to the HP update but the problem still existed. Two days ago I refreshed the computer, which rolled the operating system back from Windows 8.1 to Windows 8.0 but the Shut Down/Sleep problem is still there.