I'm looking for a good deal on a Intel 2 Duo T9400 cpu and I found a Penryn Engineering Sample Q4HQ (No Sensor) which I can get real cheap then there's the Retail version which is not so cheap. Is there any real importance getting the Engineering Sample Q4HQ over the Retail Version.
View 5 Replies
I purchased an FX 1600M to replace my fried 7900GS. BIOS didn't recognize it. At the beginning of the boot screen I realized that the card was "engineering sample" and I couldn't install nvidia drivers by double clicking on the setup file because no compatible card recognized. I only could install them from the device manager by updating drivers and pointing out the extracted drivers folder. I use A09 BIOS and Windows XP.
Everest and gpuz say that the card is Quadro fx1600. On every speed setup ati tool showed artifacts, even with downclock!
However the card managed both 3dmark 05 and 06. Actually with good marks.
The card had 2 heatpipes but since my case needed modification I decided to change heatpipes with my old GF7900 gs. With 1 heatpipe I installed it in my Dell E1705. Can it be a heat problem that atitool showed artifacts? I also use i8kfan to check heat run and while gaming temperature went up to 84 degrees. Idle temperature was 60 degrees (corrected with gpuz). I will modify my case soon and install it with 2 heatpipes again.
Does anybody know about "engineering sample" gpu's?
Intro
Acer Aspire Revo (R3600) - Pre-Retail Sample
The Acer Aspire Revo or R3600 is one of the first media centered nettops that utilizes the Nvidia ION platorm. The Ion platform consists of an Intel Atom Processor which is in this case an N230, and the Nvidia GeForce 9400 GPU. The nettop is to the desktop, as the netbook is to the notebook. The R3600 is basically a stripped down desktop , but still with plenty of functionality as well as usability.
The specs of the R3600 are similar to many netbooks out there. The CPU tasks are performed by the basic Intel N230 Atom @ 1.6Ghz, 533Mhz (133Mhz Quad pumped) FSB with 512Kb of L2 cache. The R3600 also features 2GB of DDR 667 memory and a 160GB 2.5inch 5400RPM SATA hard disk drive. Many of the current netbooks out there have similar specs and general use of the R3600 feels about the same, although sometimes can appear sluggish due to the installation of Vista Home Premium SP1. The N230 does manage to handle multithreading due to hyper threading which has been enabled in the bios.
The GPU of the Revo is the elusive Nvidia ION based on the Geforce 9400 architecture. The ION does not feature any memory, so it shares system memory. In the case of the Revo, it has 2GB of total memory with 256MB allocated to video. This leaves only 1.75GB for system use. The full specs of the Nvidia ION can be found in the chart below.
One odd thing about the Revo is it appears to be only using one memory channel while the ION chip set supports dual channel. while supporting up to 4GB of DDR2, the memory channel is limited to 64bit mode which does reduce overall memory bandwidth. One good thing is at least the Hard disk drive is in a native SATA mode (AHCI) which will help performance somewhat.....................
I am not unhappy with Vista.
View 3 Replies View Relatedif anyone has ever put any effort into removing all the crapware from the repair DVD's, to attempt to make their own fresh start?
I have started investigating the DVD's, but it would be quicker if someone had already attempted this and has information.
I have a problem with my HP dv6 1299ea laptop. I bought in in August, and was very satisfied with my purchase until lately, when it has been overheating. I have noticed that the fan is running almost non-stop for a while now, but didn't care too much, since I have been playing games and so on. But recently the fan is now running non-stop even when it's idle, or I just browse.
Today I installed speedfan, and it shows core temperature on idle of around 70 degrees C. Sometimes it even goes above 80, and that is without any games or complicated applications running - just browsing. In Medieval II Total war it stays above 80 constantly. Now, when I'm writting it shows between 65-70 degrees C. I see that speedfan does not support my motherboard, since it only shows core, no GPU, HDD, and nothing about the fan speed. Is there any other software that might help me identify and solve the problem?
I know AMDs tend to overheat, compared to Intels, but this just seems too much. I did some research, and saw that it is a known problem for HPs. I ordered a laptop cooler (Titan TTC-G4TZ), but will get it in about a week.
Just got off the phone with a tech guy at DELL XPS, I was asking about the upgrade path, and the 8800M cards, and timescales for release.
The guy says they have an engineering problem at the moment, and are "Unable to make the cards function correctly with the CPU" (for what reason I didnt ask) He did mention "proportional speeds" - so im assuming he means something about bus speeds but im not sure..and that "They have no immediate plans to release this card in this laptop".
He might well be feeding me rubbish just to try and get a sale, but does anyone have any contacts at Dell that can confirm or even deny this is true?
I was hoping that they would come out with the new card in the unit before or around xmas - seems (if this is anything close to the truth) that this is unlikely from what he said...
question: Mac or PC?
The only catch is this: in the fall, I'll be entering college as a mechanical engineering freshman, which basically screams "PC, PC!" However, now, with the advent of Bootcamp, Mac has become a plausible option for me.
I've really been looking at the Dell XPS M1330 and the 2.26GHz 13" MacBook Pro. My max budget is $1200, but, if I did my basic math right, I can get both of these around $800-900, which will make my parents happy.
I'm a big fan of OS X. I dig the simplistic and intuitive feel. I also enjoy the rigidity of the new-ish aluminum enclosures, especially when compared to the laptop I'm using now. However, I am familiar with XP after having used it for most of my computing experiences since junior high and onwards. 7 also looks like a very promising operating system.
I hear that Windows on a Mac machine runs pretty smoothly. However, the glitches I've read about do worry me: missing/lacking mouse drivers and lack of power management (also related to overheating ). VMWare and Parallels are also viable options, but I feel like it'd make more sense for me to run engineering applications natively on Windows.....
For example, if one re-installs the OS from the Dell provided DVD and then restarts one's computer, would one see the Dell's OEM black logon screen or the "hummingbird" logon screen of Microsoft Retail version?
View 8 Replies View Relatedi am having a problem installing windows xp english version on my compaq presario b1011 which is default in german . when i try to install a english version of xp it hangs in xp logo itself . when i try to install a xp english version i am getting this error
"windows xp professional setup
setup was unable to verify c:
your computer may not have enough memory to examine the drives (or) your windows xp CD may contain some corrupt files to continue press enter" this is the error message when i continue to install it installs and after installation it hangs with xp logo . if i try to install with xp german it installs smoothly without error
I don't have a Sony Style store near me (closest one is over 6 hours away). Is the AW sold in any other retail stores?
View 5 Replies View RelatedI am in the process of performing a much needed system recovery of my Acer Apsire 7720. Ideally I would like a fresh install of Vista Ultimate without all of the unneeded software added during the recovery process.
I purchased a retail copy of Vista Ultimate a year ago for my desktop but am wondering if I can perform a clean install of Vista retail on my laptop but using the OEM serial number on the bottom of the Aspire unit and successfullly activate without issues.
I installed retail Windows 7 Ultimate 32-bit on Studio 1537 (the one in the signature) So far whatever I have tested, except the touch buttons, everything works.
I wonder if anyone knows how to get those touch buttons working.
This is a laptop without Recovery Discs, where the original drive partitions were erased and reformatted as 1 big partition. During Vista installation, it always reboots just as Vista is on the verge of "Completing Installation". So near and yet so far. The BIOS shows the hard drive as an IDE drive - even though this is clearly a SATA drive. Is this a driver problem? Do I need to load SATA drivers before having Vista go through the installation?
View 4 Replies View RelatedWhich version HDMI does studio 1555 have ? I dont know why computer manufacturers hide that information, cant they say HDMI 1.3 or HDMI 1.2 instead of just saying HDMI .. i am sure USB is not confusing since most USB are 2.0 now.
View 4 Replies View RelatedWell it's been about a year since vista came out, and I'm just getting bored with XP and have been tossing around the idea about getting an OEM version of vista. Does anyone with vista running on their machine have any feedback or impressions of the OS at this point as drivers have started to reach a more mature level? I don't know if it's just cuz i got some cash to burn or if my urge for a new OS is getting to me.
View 15 Replies View RelatedI just bought a T7500 processor to upgrade my Aspire 5315. I understand that a bios upgrade should be performed before replacing the cpu. I read about some problems with bios version 1.34 and some went back to 1.33 and there is a new bios 1.43 now.
View 7 Replies View RelatedI picked up an old 256mb 500mhz G3 iBook on ebay. It currently has 10.2.7 on it, should I leave it the way it is, or go to 10.3 or 10.4?
View 3 Replies View RelatedI got the XPS M1530, 2.4 GHz, 4 GB RAM, 64 bit Vista & Blu-ray writeable. Also got Office, but the version is 2007.
Is that the latest available? Seems odd to buy a new high end computer & get old software.
Also, they have the hard drive partitioned into C: & D: The D: drive is called RECOVERY & uses ~8GB. I couldn't find where this is described anywhere. Sounds important.
Does anyone have any idea when or if Dell will be releasing the XPS laptop with the Centrino 2 chip or if they will be releasing a new XPS laptop design all together as the current design has been around for well over a year now?
After hunting around for a solid performing laptop for home and office work for a month or 2 now, I have decided that the Dell XPS is probably the best machine I have looked at. It sounds to be well built, perform great, and has a premium warranty to back it up.
The only negative things I have heard about it is the hard drive is loud and the slot loading drive is also loud, does anyone know if these issues have been resolved and updated in the last few months?
So I go to buy the laptop and realise they don’t have the new Centrino 2 chip! I assumed they would, however chip they only offer the Core Duo chip. I thought Dell was all about consumer customisation and they were able to get new technologies to the market faster because of their direct selling model? So why don’t they have the new Centrino 2 chips?
I want to buy the 15” XPS, but don’t think I can part with the best part of $2000 AUD without the machine having this latest chip. Even the new Sony’s now have the new Centrino 2 chip and they sell for around the same price for this XPS.
So my question is, does anyone have any idea when or if they will be releasing the XPS laptop with the Centrino 2 chip or if they will be releasing a new XPS laptop design all together as the current design has been around for well over a year now?
Does any one know the difference between Webcam Central 1_4 Ver 2 dated 09/21/2009 and Dell Webcam Central (Consumer) Ver 1.4 dated 11/20/2009.
I am offered both versions for download from my Dell Downloads page. Which version should I install after a clean install of Win 7 pro 64bit.
My friend just ordered a Z series, but it doesn't specifically say backlit keyboard. Is there ANY chance that the keyboard might lack back lighting?
View 4 Replies View RelatedI left my Z sitting too long not connected to power (in sleep mode) and the battery ran down. Now it will not boot up. It won't start off battery, off of power, off of power without battery -- it just blinks green, I can hear the DVD drive momentarily engage, there is a slight "beep" -- it tries this about three times before giving up and shutting down.
View 7 Replies View Relatedupload safari 4.0.3 cause i can't find it , i need 4.0.3 not the final 4.0.4 .
View 5 Replies View RelatedI guess this should be filed under Apple, since I'm using OS X. I keep getting pop under adverts with firefox, is there a way to prevent them in firefox?
View 8 Replies View RelatedThey don't seem to offer W7 with the i7 chipset, even on the business site. Â Wondering if I can just get the W8 version and downgrade it to W7.
View 1 Replies View Relatedi'm using 176.44 (driver date: 9/3/2008) from Dell.
anybody have good experience with NVDIA driver from laptopvideo2go or NVIDIA website?
I currently have a 1645 on order and assuming I ever get it, I want to run Linux as the primary OS.
I would like to run vmware workstation with windows as a client. The reason behind this is that I primarily use the computer for work and need linux, but I need windows for a few things.
I understand that these days Dell simply ships a re-install disk if that much. I need a full version of windows to setup vmware. Does anyone know if the dell key can be used with a full version disk to do an install .....
anyone with a new studio that has shipped with the windows 7 upgrade option do me a favor?
i would like to check the SLIC version on the current shipping models
Download and install RW-Everything Read & Write Utility. Run RW-Everything, then click on Access pull down menu, follow by ACPI Tables. In the opened ACPI Table window, click on SLIC tab
Ever since I setup a Mac for a friend of mine, I've been very interested in the Mac and Mac OS X. It's fairly easy to learn and runs very well. Of course, I've been dealing with Windows for over 15 years, dating back to Windows 3.1. I also work with Windows 99% of the time since I mainly work on PCs as a PC tech.
Of course, Windows will run on a Mac using Boot Camp, but it seems like there's a whole variety of glitches when running Windows on a Mac using Boot Camp. Thus, I come up with the following question: which version of Windows runs best under Boot Camp? XP? 32 or 64-bit Vista? 32 or 64-bit Windows 7 RC? Do I need to wait for Snow Leopard to come out with better Boot Camp drivers? Do I even need to wait for Windows 7 to come out?
I am seriously looking at getting a 13" MacBook Pro and will most likely run some version of Windows on it using Boot Camp. Also, depending on the version, what amount of RAM is needed? I know that if you have 4GB or more RAM, you might as well run 64-bit Windows 7. Other than that, I'll probably run mostly Mac OS X on the MacBook Pro, but having some version of Windows on the MacBook Pro running under BootCamp would come in handy. Not sure if I'll do Parallels or Fusion.
