Dell :: E6500 Running Slow When Warm
Feb 21, 2009
I'm having an issue where my E6500 w. NVS and P9600 CPU runs slow when it gets warm.
In a 30degC ambient room I only have to work the machine for a few minutes before the CPU slows down. I get an event log like -
Quote:
Log Name: System
Source: Microsoft-Windows-Kernel-Processor-Power
Date: 21/02/2009 4:43:38 PM
Event ID: 7
Task Category: (7)
Level: Warning
Keywords:
User: SYSTEM
Computer: PICOLTP04.picodon.local
Description:
The speed of processor 0 is being limited by system firmware. The processor has been in this reduced performance state for 71 seconds since the last report.
After that the CPU is locked to 31% speed. If the load on the CPU continues it will get even slower.
You can also see this in Performance Monitor on Vista, or Resource Monitor on Windows 7, as below-
Temps in the system arent (IMO) getting too high, either-
Same thing in Vista SP1 x64 and Windows 7 Beta x64. Running the latest firmware (A11). On Vista I've tried running with and without all the Dell garbage and get the same result.
View 9 Replies
ADVERTISEMENT
Jul 5, 2009
I just received my 8510P, it's built very well, looks and runs great.
But the heat of the palmrest and touchpad area is a bit bothersome.
The temps look fine, but who am I to believe the screen, or my hands?
I could not imagine resting this on my lap, the heat at the bottom is quite hot.
I'm just wondering if anyone has experienced similar heat from this laptop.
Perhaps there is a fan issue I need to take care of...
View 10 Replies
View Related
Nov 28, 2014
The grill on the left side of my Latitude E6400 gets extremely warm--especially when video is playing. The bottom side of the case, on the left side, gets very warm, as well. I've been able to confirm that the fan behind the grill on the bottom side *does* run periodically; however, the grill and underside remain very warm.
How warm? Right now, after playing a video for about 15 minutes, SpeedFan reports the following temperatures: GPU (162F), HD0 (109F), Temp1 (145F), Core 0 (140F), Core 1 (142F). All of the items except HD0 have a flame icon--indicating an abnormally-high temperature. Worse, I've seen the temperatures considerably higher than the above.
I've had this laptop for about five years. The latest BIOS and drivers are installed. It's working OK, otherwise. This problem started, suddenly, perhaps a year ago.
View 4 Replies
View Related
Nov 23, 2008
The E6500 I'm using has the P9500 (2.53 ghz, 6mb cache), Nvidia 160M, 2gb RAM, and 80gb 7200RPM HD. When I try to play a 1080P trailer from Apple's site, the thing doesn't seem like it can handle it. It's not smooth at all. I let it DL all the way too, so it's not a buffering issue or anything.
I was planning to use this on a 1920x1200 display, but if it can't even play the 1080p trailer properly...
View 10 Replies
View Related
Mar 21, 2010
Today, after I started up my 9300, I noticed that things were running very slow, and my CPU temp was low, too. I8kfan is showing the processor running at exactly 800Mhz. It's a 780, 2.26 Ghz processor
View 8 Replies
View Related
Apr 17, 2009
I've taken apart from 1730 and made sure there was no dust and its quite clean, its sitting up at the back so air is flowing through under it but when playing games all on low settings (playing demigod)
it still slows down when a lot is happening on screen, and the laptop gets extremely hot - even some parts are too hot to touch.
View 4 Replies
View Related
Apr 6, 2009
I myself have an old celeron powered inspiron 1300, 2 gig ram-upgraded myself and an old onboard Intel 900 series gfx, yada, running windows xp...
it runs on the web very quickly- but its on its last legs, powers on and off, screen flutters, it overheats ,etc .....
View 6 Replies
View Related
Jun 6, 2009
I've been trying to get Vista Ultimate to run on my laptop for a while now, and every time I install using a clean installation, it runs painfully slow. If i have more than one window open its not even worth using. So I always run back to XP and I'll be honest in saying that I'm quite bored with it.
how to make it run better with Aero?
My Laptop's Specs Are
Brand: Acer Extensa 4220
CPU: Intel Celeron CPU 560 - 2.13GHz
RAM: 1GB DDR2
Graphics: Moblie Intel GMA X3100
View 8 Replies
View Related
Feb 20, 2010
I have Windows XP installed through boot camp, and it seems the hard drive is acting very very slow. Or basically XP in general. Installations are taking a very long time. It literally took 4 hours to install Modern Warfare 2. In case anyone is wondering I have the 2008 iMac 2.4 Ghz, 1 GB RAM, 7200rpm HD. Also in device manager, under SM bus controller there is a yellow question mark, could that be part of the problem?
View 10 Replies
View Related
Feb 1, 2015
I recently received a brand new Aspire V5-123-3496 as a gift however after a week of use it still runs very slow. Although I primarily use the internet, I have google chrome, it is also general processes that take long. For example, to open the start menu, then to choose a program then for the program to open can take several minutes.
View 3 Replies
View Related
Mar 9, 2013
So i bought a Dell Inspiron n5050 5 months ago . The first day i got it i went to play games with my friends and stayed at least 10 hours playing.
The next day it went slower , in fact in minecraft the first day it was running on 120fps and on the next day about 70 - 60.
also , the laptop kept on getting blue screens and black screens and sometimes didnt turn on.
I still play games like League of Legends and Minecraft with friends and now the fps suddenly dropped . in minecraft 70 - 60 to 20 - 30 and in league of legends constant lag when someone uses a skill / attacks.
Whenever i go to sleep i just close my laptop , i dont shut it down and also i run at least 6 hours a day. Ive also heard that it might be the cooling fan that has dust in it, however im not sure. I want it to run smooth again . Ive reseted to factory setting twice and its still running slow.
View 6 Replies
View Related
Nov 2, 2008
I'm guessing I did this to myself somehow but I can't figure out how to fix it. It originally came with Visa but I downgraded to XP and had been using it without problems for awhile. It started getting a little slow so I recently installed (and soon after uninstalled) a bunch of optimizing / driver updating programs. After playing around with those, my laptop is running super slow... I can't watch videos, the buffer causes it to just show the image while the audio plays... After running Dr. Hardware it looks like my CPU is only running at 800mhz which is a lot slower than it used to.
View 10 Replies
View Related
Mar 2, 2010
i just disassembled my dv5t to fix an issue i was having with the screen. the screen seems to work fine now however it is running ungodly slow.
in order to get to my screen cables i had to take out the Following:
-hard drive
-WLAN module
-Switch cover & keyboard
-the display bezel
i'm not exactly sure what might be causing this because it was working just fine (except for my screen issue) before the disassembly
also it seems to run a little bit better in safe mode but its still slow
after playing with it for a while its main problem is booting and programs are crashing. it takes about 10 minutes to fully boot and then it runs at a normal speed however programs keep crashing like crazy.
View 10 Replies
View Related
May 8, 2009
Recently my games and videos are running real slow on XP.
Especially noticeable while sounds are going, for example on youtube, sounds like its on slow motion.
View 5 Replies
View Related
Oct 8, 2014
My PC model # is G42-490TU , Product # LR783PA#ACJ , Processor - Intel Core (TM)i3 CPU M370 ,
RAM : 2.00 GB (1.86 GB usable) , System Type : 32-bit Operating System .
My PC has been running very slow lately . It hangs , freezes , pages become unresponsive and hence, it takes lot of time to type . I have to use it daily for work so, I want to resolve this asap.
Would like to increase its speed to be able to work smoothly on it daily. Would like PC to run fast. How to increase its RAM ? Does it cost to increase the RAM ?
Also , reading some prev posts I downloaded this link - [URL] ..... to determine the chipset info and following is the result I received . Pls let me know if increasing the RAM to 4GB will resolve my system concerns making it run fast and does not lead to any hangs / freezes etc .
How to go about increasing the RAM ?
View 2 Replies
View Related
Apr 25, 2014
My X1 Carbon started running super slow since last week. The disk C: shows I still have 49.2 GB free space to use. So I think the problem does not relate to the space size. I am wondering if there is any way to clear something in my computer and make it run as fast as before.
View 2 Replies
View Related
Feb 1, 2013
I have first gen intel i3 processor with 4gb ram. I recently installed windows 8
Computer running very slow during data transfer and disk transfer goes to 100% and even the computer freezes for low disk.
transfer rates
View 3 Replies
View Related
Nov 15, 2007
Then it's time to go through and clean out your system! My M170 has been running warm just idleing. Start up a game and keboard feels like it's going to catch fire! Looking at Fangui, I was hitting 80C on the CPU side, and 110C on the GPU side while gaming.
Idle was sitting at 44C CPU, and 60C GPU. Not good! I'm honestly surprised that my system just didn't straight up melt through my desk! But, this is testament that the 7800GTX and a pin-modded 1.7>2.26 can take the heat.
I took the thermite paperweight with me to work today, tore it down completely, and was just bewildered by how much dust was trapped in the heatsink fins. The fans were coated with dust, but weren't too bad. And the grills on the case just needed a good wiping.
Looking from the outside, you just can't see the amount of dust those fins are able to trap in the case.
Also while it was torn down, I re-gooped the GPU/CPU's (cleaning off the previous AS5), and then put the system back together. I'll admit, I'm not using AS5 this time around.
Instead, I bought some off brand stuff from the local computer boutique. After reassembly, Fangui was showing temps of 32C CPU and 38C GPU. Much better! Played some Call of Duty 2 and Gears of War and the system didn't even break a sweat! After 15 minutes of gaming, my M170 was running a fairly cool 55C CPU and 78C GPU!
Now I can finish CoD 2 tonight (beat it before, just going through it again before I start CoD4), and play some more GoW without the system crashing!
CoD2 is running buttery smooth at 1920x1200, max settings, and GoW is sitting on 1280x720 w/ max settings...no slow down in the intense fire fights, and the game just looks remarkable.
View 15 Replies
View Related
Jun 24, 2009
i got my new hdx and i decided to buy a game for it as well. I popped in warhammer:dawn of war 2 and it played well on mostly ultra-high settings. however the machine gets HOT after playing for about and hour. i also experienced this while playing crysis. it could have something to do with my cpu running at 45w but idk. anyways so i continued to play a little more warhammer and then i started seeing artifacts on my screen. before i knew it my screen was unviewable as the artifacts took over. I thought i was buring up my gpu so i quickly logged out of the game. my screen was still artifact filled so i turned off the computer and rebooted. everything seems to be fine till this moment and i think im very lucky. now i have my hdx raised up on all 4 corners with small business cards and i have my fan blowing at the bottom of the laptop from the right side. (This fan is blowing the same direction that the laptop fan blows). i also put my battery in front the of the fan so that would kool as well. so i decided to give warhammer another shoot. i played it for 2.5 hrs straight and the computer remains cooler that i expected. the battery too is way cooler. i would say my cheap cooling system worked after all.
View 3 Replies
View Related
May 28, 2009
I have my macbook pro getting pretty hot without much usage.
Eg. I am on integrated graphics right now and my cpu usage is roughly 30 percent (inclusive of system and user) and nothing is very intensive. Just a couple of firefox tabs in a firefox process, colloquy and itunes. I have about a 70 degree CPU temp and a 57 degree GPU temp on the 9400M.
It gets worse when I go on discrete and do the same things. My CPU often hits 80-90 degrees with my GPU being right htere at about 70. I'm pretty sure i need to get this checked out, but does anyone else have the same issue as me?
View 10 Replies
View Related
Sep 5, 2009
Just bought a Sony Viao 448 J/B the palm rest gets very warm almost hot when running. This is my first Viao so I'm not familiar with the normal symptoms.
View 5 Replies
View Related
Jul 1, 2014
I have Compaq Presario CQ42-273TU NBPC. In my laptop , if i play video , it becomes very slow. After video becomes slow, everything else on the laptop becomes slow. recently i gave laptop for service also, then also i have issue with video.
View 8 Replies
View Related
Feb 2, 2013
I have an Inspiron 7010 which is 2 years old. In control panel devices it tells me to troubleshoot the laptop and cannot rectify problem with Broadcom virtual wireless adaptor. Secondly running the diagnostics say the Read test is not running. These are the only problems but are not affecting the efficiency of the PC. Should I ignore it?
View 1 Replies
View Related
Nov 18, 2009
I've been noticing that my computer's been running hot for some time now but am finally posting because I've been noticing that if the computer reaches a certain temp, it tends to throttle back which can be a bit annoying......................
View 10 Replies
View Related
Sep 8, 2009
Got a new E6500 last week, and I love it! I got the audio crackling to go away, though there are minor latency spikes every couple minutes,
that however don't affect the audio/video. The screen is wonderful, the keyboard, everything.
But one thing that bugs me is that when the fan starts going it will never stop. According to HWMonitor, my processor (P8800) can be at 29-30 deg C (right above ambient!) and the Nvidia card at 43 deg C and it won't stop! It's extremely annoying
View 6 Replies
View Related
Sep 29, 2008
I managed to buy a E6500 through a special promo at my university. Although I wanted an integrated graphic card (I'm not going to do *any* gaming so the nvidea cards are completely useless for me, right?), the promotion was limited to the nvidia 160.
Now what do I see upon receipt, they screwed up at dell: they delivered a notebook with the intel graphic card and no bluetooth. I've noticed them and they'll replace the notebook. Now I was thinking if I would be able to make a deal with Dell: send me the BT card that I'll install myself and some compensation for the missing graphic card (which I actually didn't want anyway).
Would I be able to pull off something like that, and what 'compensation' would you try to get (I already have max RAM, extra 6 cell battery, mouse, ...)
View 10 Replies
View Related
Jan 19, 2009
I'm planning on getting an E6500 with the 64GB SSD (performance option - I assume this is the Samsung SLC version).
It's my understanding that SSD's run a lot hotter ( since they are solid state chips) than a corresponding conventional HDD.
I would also think that they would consume less power than the conventional HDD, but what about the additional heat causing the fan to come on more often and/or at higher speeds? Would this negate the power savings?
Any comments would be appreciated. Also, FWIW I will be sticking with the Intel 4500MHD integrated graphics.
View 6 Replies
View Related
Oct 31, 2008
I recently purchased a Latitude E6500 with fingerprint reader. I was so impressed with the Studio15 that I had. Here is the problem the software with the E6500 doesn't let you login on websites or programs, like the Studio did.
When contacted Dell they stated that it will only work with Vista. My E6500
came preloaded with XP Pro. So I bit the bullet and downgraded to Vista.
Guess what still no use except to log into windows. Wave software SUCKS!
Does any one know of software that will work in XP with the Latitude?
Digitalpersona does not have a XP version yet. Yet on my Studio I converted to XP and it worked. Anyone have a link to the fingerprint software on the Studio?
View 10 Replies
View Related
Jan 4, 2009
I just play a few games here and there and I am seeing my system slow WAY down when even just doing light gaming. Is anyone else having these issues? I have the NVS 160 and the T9600 and even playing games like Command and Conquer Generals Zero hour which is a game that is several years old, I have to play it at 1024*768 with details turn down to min just to get the game not to spit and get jumpy. Its like it freezes every 2 seconds for a half sec or so..
I have speedfan monitoring temps for CPU and GPU and both are well within normal ranges, infact the fan is not even turning much past 4000 RPM and GPU getting no hotter then 64C at MAX..
Any ideas or experiences would be greatly appreciated. I just feel that the NVS 160 should be able to play a 3 year old game MUCH better then it is...
View 10 Replies
View Related
Apr 24, 2009
I have recenltly bought a e6500 everything was fine till I tried to install windows vista 32 bit again . The boardcom USH w/touch sensor was not installed in my former OS and I didn't have boardcom TMP neither .
But my fingerprint worked fine .
Then I reinstalled the windows and installed the latest drivers in order . I also updated the firmware but none of those helped me solve this problem .
When I try to enroll my finger print I get : "Device opened" and when I choose my thumb as an enrolling finger I get "an error occurred during enrollment please re-enroll"
Is there any thing that I can do ?
View 5 Replies
View Related
