I upgraded my dell n411z to one block 8gb memory ram, after this, the laptop doesn't boot. Also not enter to the bios. In a old post i read that the laptop has two memory slots, however, when i replaced the memory only see only one slot. Previusly i cheched the memory compatibility and it's acording to the specs. When i returned to the original memory it works. Why can't i upgrade the memory?
View 3 Replieshow to upgrade memory my notebook, because I have a notebook inspiron 1564 with 4Gb RAM and I'd change to 8Gb RAM. But searching int internet I' ve found only memories with frenquency 1333Mhz and the memories in the my notebook are 533MHz.
Is there any problem and is it possible upgrade memory ispiron 1564 4Gb to 8Gb?
Is it possible for me to upgrade my memory capacity?
View 10 Replies View Relatedi have a dell n 411z laptop it's not charring after 43% .i Change the battery & adapter .but i'm havering the same problem .......
View 1 Replies View RelatedI have upgraded to the latest bios and my fan still seems to run all the time.
View 4 Replies View RelatedAny more. Status shows that battery is still charging. What's the resolution for this issue?
Screen shots are given below;
I have a N411Z and the fan has started running all the time, what gives?
View 7 Replies View RelatedI have the same problem. I have an Inspiron 14z (N411z)
My battery light is flashing orange and the battery icon says that my charger is plugged in but not charging. So when I unplug my laptop it automatically dies. It's been like this for about a week and I've tried everything I found online including
Battery Health says 'System cannot communicate with battery'
Battery Status says ' Battery Charging disabled'
I tried to flash the BIOS by downloading the latest version, however it gives me an error message saying battery needs to be atleast 10% to flash BIOS. Or, it says 'Service already exists'
I bought the laptop in 2011 December, but didn't start using it until October 2012. The laptop is relatively new in terms of usage.
I installed a new hard drive on my Niece's laptop Inspiron 14Z (N441Z) and did a clean install of Win 7 Home Premium. I installed the Chipset drivers first and then started on the list displayed in the support area for this machine. After completing all of the drivers install, my device manager looked like this:
The Unknown Device shows an ID USBUnknown. This machine has 1-USB2 and 2-USB3 ports. If I run the Dell Diagnostics it shows that I have 1-1.1 USB ports, and 2-USB2 ports. The 1.1 port appears to works since it will recognize flash drives etc. This is also true of the of USB2 ports. The other USB2 does not recognize anything except my Samsung Galaxy 4 phone. But when it is unplugged I get a balloon on the task bar that says a USB device is not recognized. This will also occur when I first boot up the machine. It is like the machine is not recognizing the USB ports If I run any of the hardware troubleshooters that Microsoft has it tells me that a driver is missing but when it tries and install, it reports that it fails. I have undated my bios, all drivers, I have uninstalled drivers and then rebooted with no luck.
My laptop is dell Inspiron N411Z, am having a problem :
MY WEBCAM IS NOT WORKING,SHOWN AS"NO SUPPORTED WEBCAM CONNECTED",
IN DEVICE MANAGER ,NO IMAGING DEVICE FOUND.
Last night my dog ran over the keyboard of my Dell Inspiron N411z . The screen now displays upside down. I can fix it manually by using the Fn key and the F1 key which brings up some screen options, but I'd like to permanently fix this. Oddly enough my dog did this to my other laptop a few years back. I'm not sure what he's running across to do this.
How to fix this so the screen isn't upside down every time I start the computer?
I have Dell inspiron N411Z (2009). the webcam stoped to work after skype upgrade. I found out that windows doesn't recognize the webcam. I install the driver Creative live! 2009 or 2011. But it's useless.
View 2 Replies View RelatedI am trying to download drivers for a Dell Inspiron 14Z -N411Z to a USB drive through another laptop, because the hard drive on that Dell completely gave up. There is no installation software disc as it was on another partition on that same hard drive.
When I attempt to install the drives required to the USB drive on my Toshiba, it first wants to install the dsd.exe file before I can download the drivers. After I downloaded that dsd.exe file, I don't seem to find a way to install the required drivers as well. the DellSystemDetect.exe file wants to do that for me, but it is not on the correct laptop.
What do I need to do, to get those drivers downloaded on the USB, so I can complete the installation. I already installed the Windows 7 Home Premium (x64) on the Dell laptop.
I just purchased a used Elitebook 8540w with i7 quad core and four memory slots (I love it!). It is running 64 bit Windows 7 Professional It came with one 4gb memory module and I purchased an additional 4gb module to bring total RAM to 8gb.
I have the HP document that shows for two 4gb memory modules, one should be in memory slot 1 and the other in memory slot 3 for correct functioning of dual channel memory. All set right?
Not quite. In the Elitebook 8540w, the primary memory slots under the keyboard are clearly labeled "1" and "2" However, the expansion memory slots on the underside of the chassis are also clearly labeled "1" and "2" Opps! There is no "3" and there is no "4" In which of the unfilled three slots do I install the second 4gb module for correct functioning of dual channel memory?
I have a N411z with a Conexant audio card. I have upgraded to 8.54.45.0, A04. Can I get this card to recognize a audio in source via a USB port?
View 1 Replies View RelatedI got my hard drive replaced yeterday but now I have no internet connection, it is a dell inspiron n411z. I have the drivers and utilities cd and have tried installing all of the drivers on it, some have checkmarks and some dont so i am confused. What do I do if i installed them in the wrong order? My internet is still not working and there is a yellow box with an exclamation point by the following items: ethernet controller, network controller, pci simple communications controller, sm bus controller, universal serial bus controller, and unknown device. I had this problem last time the hard drive was replaced and somehow fixed it using this CD but I cant remember how.
View 2 Replies View RelatedI have a 2.5 year old E1705 notebook. I'm going to upgrade to W7 soon and in the process I thought I'd upgrade my memory from 2GB to 4GB.
I ran Dell's utility from their tech support page and it seems to be the case that the maximum my computer will support is 2GB! Is that possible?
In any case, I ran a diagnostic program (from Dell's utility) and it says my computer has two memory slots, and currently each slot on my computer has "Dual In-line Memory Module 1GB, 533, 128X64, 8K, 200", whatever that means.
I assume the 533 is memory speed (Hz) value. So according to Dell's utility, I am unable to increase the amount of RAM, but I could, for instance, "upgrade" to better chips (i.e., Dell sells DDR2 SDRAM Memory Speed: 800 MHz). Price would be $56.
I'm planing to upgrade Ram Memory of my DELL XPS 15z for running some virtual environments. My question it's about the max amount of memory that the laptop support and the compatible memory modules. In some forums I read about 16Gb, but Dell PcCheckup shows 8Gb as the max amount of memory.
View 6 Replies View Relatedcan i upgrade from 2GB to 3GB or necessarily i have to go to 4G?
tks, Douglas
I have a Dell Inspiron 9300, about 4 years old. I bought it with 1 gb RAM, and I'd like to extend the life of it by a few months, and make it a little faster.
This is the RAM that dell recommends for my laptop to upgrade:
http://accessories.us.dell.com/sna/P...x?sku=A0758238
Unfortunately, looking at my order when I first got the laptop, it says this .....
I have a Dell XPS M1210 notebook with 2x512MB DDR2 533MHz Memory. Now i wants to upgrade my memory but there is a lot of confusion in what module
i should buy.
After going through several sites i have came up with a few options and understanding them is so far above my knowledge.
There are 533MHz and 667MHz available ...
i do not know which one should i use .
There is also question of dual channel and shared channel ... where i am totally lost.
My hdd crapped out and I'm replacing it - I am toying with the idea of upping my memory as well. Current memory:
DUAL IN-LINE MEMORY MODULE, 256, 333, 32X64, 8K, 200
I am looking at one stick of:
Transcend 1GB 200-Pin DDR SO-DIMM DDR 266 (PC 2100) Notebook Memory Model TS128MSD64V6A - Retail
I mainly use office and surf the net.
PROCESSOR, 80535, 1.5G, 1M, PENTIUM M BANIAS, PLASTIC GRID ARRAY, INSPIRON
1) Given my usage and proc, is adding 1gb overkill?
2) Is there any advantage to getting 2 new sticks of 512, rather than one new stick of 1gb and 1 old stick of 128mb?
3) Is there any advantage to getting higher-speed ram (PC>2100)?
I own a XPS17 L702x 3D (4 memory slots) Installed memory 2x 2GB + 1x 4 GB = 8GB
I would like to upgrade the memory to 16 GB by adding one 8GB module.
Is this possible ? On the dell website I cannot find the XPS17 with the memory configurator.
I have a dell E6400 Latidue with 4 Gig of memory I would like to upgrade to 8 gig. I need for my building control software. Were can I find 8 gig .All I can find is the 4 gig memory updates which is what I already done...
View 3 Replies View RelatedIf the information below is true, then why does Dell offer 6&8 G memory upgrades in the configurations? (Main points highlighted in color)
Memory
Connectors two internallyaccessible
SO-DIMM
sockets
Capacities 512 MB, 1 GB, and
2 GB
Memory type 1066 MHz DDR3
SO-DIMM
Memory
configuration
possible
1 GB, 1.5 GB, 2 GB,
3 GB, and 4 GB
Just wondering, as I have been "window shopping" today. So far, it looks like Dell's upgrades are actually cheaper than DIY kits. I guess you could subtract whatever you could sell your stock memory for.
To anyone who has actually opened theirs: Does it really only have two slots? 3x2 Gb kits are around 100-150 USD, depending on where you look. Would be too convenient to have empty slots to stick extra 2 G modules into...
I keep running into a problem with windows not loading after installing new RAM. I am currently using the original 4GB (2 x 2GB) it came with and I am wanting to go with 8GB (2 x 4GB). I am using the recommended Crucial RAM and I have checked the BIOS which recognizes the new memory. The BIOS is up to date running A16 version. I have not been able to find any settings that would be inhibiting it from running. I have noticed that the currently installed RAM runs a 1067mhz even though it is rated at 1333mhz. As far as I can tell there is no memory remapping feature for the BIOS which does not make sense.
Here is a snap shot of what I have:
Operating System
System Model
Windows 7 Ultimate (x64) Service Pack 1 (build 7601)Install Language: English (United States)System Locale: English (United States)Installed: 9/29/2014 3:01:57 PMBoot Mode: BIOS (Secure Boot not supported)
[Code] .....
Anyone could tell me if this is feasible to be installed on the TZ.
> OSWIN32 >
http://www.fadfusion.com/selection.p...er=10122600671
I'm looking at purchasing an FW with only 2g of RAM and upgrading it myself cheaper than I can do buying it from Sony. The RAM from Sony is DDR2-800 PC2-6400. where to buy a couple 4g modules (2x4, 8g total)?
View 3 Replies View Relatedi currently have a TM 5720 with 2GB of ram. I was thinking of upgrading it to 3GB. I was wondering if you think it will make much of a difference and whether any of these would be suitable (already done a small bit of research)
i cant post any links but had seen a few on play.com
2gb pc 5300 200 pin
would it matter that there would be 2 different types of RAM in the laptop.
I found out from the release notes for BIOS 3.60 that one of the changes is to "update kernel code for 4GB memory support". Does it mean that if I update my BIOS from v 3.33(dated 9/1/07) to v 3.60 I will be able to increase my current maximum memory of 2GB to 4GB in Acer Aspire5610z.
View 5 Replies View Related