I am going to do a clean install on my system using Vista 64bit.
I saw the reformat and bloatware removal forum and wanted to know to I need to install the AHCI driver during install and if so where can I find it for my system,
I read somewhere that I do not need to install the driver as the Vista install cd that came with my system has the driver on it .....
I'm gonna clean install Win 7 on my notebook, can someone point me in the direction of an ahci driver,
as I assume I'll need it on installation like when I clean installed Vista?
I want to install mediadirect on my xps 1530. I want to follow this Dell Vista Laptop Reformat and Bloatware Removal Guide
But I have a question before beginning.
This paragraph : AHCI Concerns: On new Dell systems, they are set up to run in AHCI mode which will give you a 15% system performance boost. In many instances, the AHCI driver MUST be installed during the initial installation process for the installation to work.
Those not installing it are finding that their system may BSOD or hang during the installation and saying "Completing Installation Process". One must find the driver specific to their system either on the drivers disk that came with their laptop or at www.Dell.com in the drivers section.
Download and expand it to a USB drive or disk; the USB is preferred but it is important that you expand it on the media you just saved it to. Once done, put it aside for now .....
I reformatted my inspiron 1520 but didnt load ahci drivers (vista didn't find them). When I try and enable ahci in the bios, i get a bsod when vista is booting. How do I get ahci enabled?
View 10 Replies View Relateddo i need to slipstream the driver into my DVD when burning the windows 7 image onto my DVD?
if i need to, how can i do that??
I am using ATA mode with XP. Lately I switched to ACHI in bios and do a clean installation.
During setup I press F6 to install ICH8M driver. The driver is loaded sucessfully from a floppy disk.
Later when the windows installer prompt whether to Install Windows, Repair or F3 to quit; I select install windows and it prompts unable to detect hdd.
I recently undertook a clean install of Vista (SP1) onto my XPS M1530. After the installation was complete,
I manually installed the Intel Matrix Storage Device drivers (AHCI).
When I view the IDE ATA/ATAPI controllers list in Vista's Device Manager I see the following:
- ATA Channel 0
- Intel(R) 82801HEM/HBM SATA AHCI Controller
- Intel(R) ICH8M Ultra ATA Storage Controllers - 2850
does anyone know how to enable the AHCI feature on that notebook? Ther ist no possibility to change it in the bios.
View 6 Replies View RelatedThis is my 3rd attempt trying to reformat.
With the AHCI driver.
When i reached that part to install the driver, i clicked on that "drivers", connected my USB and added the AHCI driver.
I am looking into installing Vista Ultimate x64 and was wondering if there is anyone here that has upgraded to vista 64 bit and what they did as far as drivers go. Mainly I am just trying to get all of the drivers ill need found before doing anything.
View 9 Replies View RelatedI've tried using the ones from the Dell web site but I cannot get them to work, just incase i'm being a dill can someone link me to the correct AHCI drivers please?
View 4 Replies View RelatedI am about to install Windows 7 thanks to my school's MSDNAA program and plan to use the 64-bit version (replacing Vista/32-bit). I remember from the bloatware removal thread where it is highly recommended to install the AHCI driver before installing the OS since there is a performance boost.
Should I continue to use the AHCI driver before installing Windows 7? On Dell's site, they only list vista versions, so I don't know if it is needed or if it even works with 7.
If I should keep using it, should I use the 32-bit or 64-bit driver on Dell's site? I know it sounds obvious that I would want the 64-bit driver if I am upgrading to a 64-bit OS, but I have heard people say many 64-bit drivers are not as reliable as 32-bit, so I am wondering if it matters which one I use
So just for fun I switched my drive operation mode from AHCI to IDE and installed Windows XPSP3 32bit.
I went around collecting drivers until all my devices were recognized, and then slipstreamed the drivers along with the newest Intel Matrix driver(extracted from the installer) onto a custom install DVD using nLite.
Shut down, set drive mode to AHCI, booted from CD, and then BAM! BSOD halfway through install initiation
I am following the bloatware removal guide and once I get to the part in the setup where I have to point it to the Intel Matrix file I put on a CD,
it eliminates all but one file that it says is compatible with my system, but then that file will not work to install
So I am trying to find the AHCI driver for my m1530 but I dont see it under drivers for my service tag, does this mean I dont need it? In my BIOS I have that as an option though!
View 4 Replies View RelatedI have a Dell laptop Inspiron 11 3000 2in1. I decided to swap my Dell Sata 54000 rpm HD to a SSD M500 240GB. I went in the BIOS and it does recognize the Fixed HDD - Crucial_CT240M500SSD1 240GB. I tried installing Windows 8.1 and it would not recognize the SSD HD. What I notice if I go in the BIOS and change SATA Operation to ATA it works fine. I would like to have it on AHCI because I guess that is the latest technology for reading a HD. Any reason why I can't install it with AHCI? It also did work fine before on AHCI with the factory HD that came with the laptop.
View 2 Replies View RelatedYesterday i got my new XPS 15 9530, that's where i ran into some problems.Laptop is unable to work under AHCI in any possible configuration.It ships with 32GB SSD + 1TB HDD, i unscrew and swapped the 1TB HDD with a new Samsung 850 Pro 512GB. I started installing windows while on Intel's SRT (raid), then i noticed it and after installation was over i changed to AHCI.
Then i had to re-install, i boot using windows disk (talking about 8.1 pro) and windows installer was slow during this period... then after i reached the drive listing, i couldn`t touch either drivers. I couldn`t create partition in the samsung pro, i was receiving the 0x80070057 and a couple errors more of the same type. I started playing around with the GPT & MBR formatting, used external computer to create partitions, layouts but nothing.Whenever AHCI is on, i can`t manage to work using the Samsung 850 Pro disk.
So now i`m using Intel's SRT (raid instead) while having a single disk (samsung 850 pro) where windows is installed, while not achieving full read/write speeds because of the samsung magician that has to work with AHCI, and the Intel Rapid Storage Technology (irst). The other drive (32GB SSD) is formatted for linux, i have to disable secure boot to boot into there but that's fine.How can i get AHCI to work? I tried so many ways but clearly nothing..
got a inspiron 1545 recently with a SATA 320 gb HDD / 4gb ram with Windows Vista Home Basic. Like most of us I hate Vista. So I created a partition & installed XP.
Used a program "EasyBCD" to setup dual boot. I get the dual boot screen at startup. But only XP boots. After a little probing, came to know that there are only 2 options in the BIOS for SATA operations. AHCI & ATA. If I select ATA I can boot only to XP. If I select AHCI then I can boot only into Vista. Searched around but the solutions were a bit over my head. Really appreciate if anybody could come up with something in lay mans terms.
I bought new Inspiron 11 3147 (2 in 1 model). When "SATA Operation" is set to AHCI laptop can't detect SSD (Intel 530) in Windows 8.1 setup.
When I change "SATA Operation" to ATA Windows 8.1 can detect SSD in setup without any problem.
I think this is BIOS error. There will be any update? I can't use my SSD now.
when I got my 9400/E1705 I was always sad for not having the AHCI option available in the BIOS.
This was asked for so many times:
- "Notebooks BIOS should support AHCI"
[url]
- "Enable AHCI in Dell Notebook BIOS"
[url]
- "Please give us BIOS support for SATA AHCI mode on Inspirons!"
Please give us BIOS support for SATA AHCI mode on Inspirons!
- "Give us real bios control"
[url]
- "Bios release"
[url]
In the Sony forum, they have found a way to activate these options even if they're not present in the BIOS:
How to Enable Intel VT and AHCI on a Napa/Santa Rosa platform Phoenix BIOS Vaio laptop
...
The only item you'll need is a bootable DOS media. Click one of these links for instruction for creating a bootable floppy disk (with USB floppy drive) or usb stick.USB flash1 or USB flash2 or CDR (add modified table file to image before writing).
Instructions:
1.Download symcmos and copy it to your bootable DOS media. This utility is used to modify your Phoenix BIOS settings. Also, download a DOS text editor and copy it to the media if you feel comfortable editing a file in DOS.
2.Go to the BIOS by pressing F2 during start-up, or when the VAIO logo appears, and reset the settings to factory default. Save and reboot.
3.Go back to the BIOS and enable the boot from external devices option. Save and reboot.
4.Press ESC when the VAIO logo appears to bring up the boot selection menu and select the bootable DOS media. At the prompt, type "symcmos -v2 -lDefault.txt", without quotes, and note that there's no space in between the flag and filename. This will create a literal symbol table from the NVRAM named Default.txt which contains all the current BIOS settings. Reboot by pressing Ctrl+Alt+Del. If that doesn't work, hold the power button until the notebook turns off.
5.Use the DOS text editor (or boot to another OS and use a text editor there) to edit the generated Default.txt file. Change the following lines and save the modified file to something else (e.g. modified.txt):
For Napa SZs - R0112N0
AHCI: (015C) [0000] ---> (015C) [0001]
VT-x: (0354) [0000] ---> (0354) [0001]...
I just got a studio 1737 and want to do a clean Vista 64 Home premium install.
I was going to follow Les's guide in the main dell forum but it seems media direct 4.0 will not allow me to boot from the cd.
So I want to boot from Vista and reformat and install the OS.
i did a test in HDtune and i found something strange :
ide mode : burst speed - 120mb/s
cpu usage : 6,7 %
AHCI mode : burst speed - 68mb/s
cpu usage : 21% ( no mistake )
is this normal ? Hard disk is WD scorpio black 320gb
in HDtune i see that my hdd is set to ide - 100mb/s instead of sata
also when i connect a usb device ( after 3 connects especially) i get a BSOD and the error 0x0000008E .
I never got this error before and it all started 1 month ago, out of the blue.
I installed a Samsung 840EVO 500GB SSD in my Precision M4400 last weekend. I managed to get it working but it only works in ATA mode. All others modes I tried brought me to the windows splash screen quickly followed by a blue screen that flashed so quickly I couldn't read it before the system rebooted. If I let it reboot it continues to do the same thing over and over. As I understand it I would really benefit from the performance AHCI offers, particularly when running multiple programs at once.
How I might get my drive working in AHCI mode?
I am trying to enable AHCI on my HDX16t so that I can get the most out of my intel SSD X25-M.
I plan to do a default system restore by using the "Clean Vista install WITH NO ACTIVATION" thread with an original vista CD.
1) how to enable this?
2) Is it enabled by default?
3) And if so, how can I tell?
i have Pavilion DV5-1112ea with limited BIOS
i want to change my IDE SATA TO AHCI...
how i can do this ?
I upgraded my hard drive to a SSD and that is done. Laptop works fine. Installed the Samsung SSD software and it says I need to Enable AHCI to get the SSD running at full potential.
I searched the BIOS and do not see anyplace to change this. I then went to the Device Manager in Windows 8.1and I do not see any ATA/SATA controller. All I see is a RAID controller. RAID controller in a laptop?
How to enable the AHCI?
I just got my new 1720 Inspiron, and I had a problem when trying to create an image of the C and D drive using the Ultimate Boot CD (BART), it would never see my hard disk partitions. I changed the BIOS setting for the On Board Devices from AHCI (default) to ATA for SATA operation. I also had to change the Flash Cache Module to be disabled, it was enabled in the Factory Default. The result of these changes was good, I was able to see my C and D drive when booting from my Ultimate Boot CD. What these changes do? Should I leave my BIOS at the new setting, or will I lose performance from my hard disk?
View 5 Replies View RelatedI am trying to install a hybrid HDD with solid state and a mechanical back-up. The SSD portion works but I can't run the HDD utilities to turn on the mechanical drive portion. I need to turn off RAID and activate AHCI (Advanced Host Controller Interface) for HDD's in the Bios settings. It would also be nice to update my bios as the revisions come out. I need to override the Password...
View 1 Replies View RelatedSo I wanted to try out WinXP, to see the performance difference.
At first, the WinXP setup wasn't able to see the HDD. So I changed the SATA Controller Bios mode to IDE mode. (was AHCI for Vista).
I managed to install so have a dual booted system. However I can't use IDE mode for Vista. (must switch SATA bios each time).
Everything installed fine. Even got 3dMark06 increase of 150 points (not much lol). Oh and CrystalMark of 100K instead of 90K on Vista.
But I'd like to use AHCI mode for WinXP. Saw a link in a WinXP 5930g Guide, however that link was out of date.
The driver was called: "Intel(R) ICH9M M-E Family 4 Port SATA AHCI Controller - 2929 Driver".
I just got my new laptop
newegg.com/Product/Product.aspx?Item=N82E16834115487
and bought a few things when I got it First More Memory:
newegg.com/Product/Product.aspx?Item=N82E16820145598
And then a New WiFi Card for the "N" Capability:
google.com/products/catalog?q=Wireless+Mini-PCI+Card&btnG=Search+Products&hl=en&show=dd&cid=8092731164088150216&scoring=p&sa=N&start=25#ps-sellers
And a New Hard Drive for the Windows XP x64 Install
newegg.com/Product/Product.aspx?Item=N82E16822136278
But my Real issue is the AHCI Drivers for XP x64. I am trying to slipstream the AHCI Drivers into my x64 disk using nLite and I amhaving a Hard time finding the Drivers.
I found these:
downloadcenter.intel.com/Detail_Desc.aspx?agr=Y&ProductID=1809&DwnldID=14794&strOSs=109&OSFullName=Windows*%20XP%20Professional%20x64%20Edition&lang=eng
but they are .exe and I have no way to load them.....................