my NC8000 will not start. When I push the power button the laptop turns on. The fans spins but nothing comes on the screen and then it shuts off. This lasts for about 10-15 seconds. I can try to start again but it happens over and over. Is there anyway I can repair this. I have noticed it is a common failure but don't know why.
View 4 RepliesI'm having problems with my hp DV 9500 laptop. It started 2 days ago, on start up my screen is completely red then the windows logo appears with black splayed around the outside edge. When i'm surfing the net some pages are appearing with red patches but apart from this my laptop is working fine. I uninstalled the drivers for the graphics card and re-installed this made no difference. I hooked up an external monitor and that works perfectly,
View 4 Replies View RelatedI've seen lots of posts about laptops that won't start but none with the exact same problem as me. When I press the power button it lights up and it sounds like it's going to turn on but nothing happens. There's nothing on the screen. It sounds like it used to if you closed the lid while it was on.
View 8 Replies View RelatedI'm having this extremely annoying problem with my HP Pavilion dv6-model1334us. Everytime I try to start up my laptop it always shows the menu screen saying Launch Start Up Repair or Start Windows Normally. I've tried to do a system restore multiple times, but the screen just stops on a blue screen. No it isn't the Blue Screen of Death, but it does attempt to start but fails and stands on the screen until it automatically or manually shuts down.
View 7 Replies View RelatedMy Inspiron 5421 won't start. I can hear the drive start and after a few seconds I get a 4-beep code (RAM read/write failure). The warranty expired about 6 months ago.
View 3 Replies View RelatedLooking for a Boot Disk or Start up disk for an Aspire 4720Z or a place to download one. She has been doing finals etc for the past week without it at college.
View 5 Replies View RelatedMy Dell Studio 1555 won't start anymore. When I want to turn it on, I get a beeping signal (2 beeps) and nothing happens. I tried all possible troubleshooting tips from the dell website (disconnecting all power and hold power button, reconnect to power, checked battery with the button on the battery, all fine, can't get into bios because computer doesn't start at all) but nothing works. Recently I also checked if the motherboard is connected properly and there is no issue either.
I also purchased a new dell adapter because my old one was a little bit damaged. The adapter is like the old one, and it's originally dell and the correct one for the studio 1555 so it can't be the adapter. Laptop also doesn't start when the battery is not in and it's only connected to the power.
my 2 brothers were playing warcraft 3 together one on the desktop the other on the laptop. after playing a long game they shut it down for the night. the next day my brother went to start up the laptop and nothing happened. for some reason it simply will not start up. the battery is not dead and he has tried starting it while plugged in.
View 10 Replies View RelatedMy C762NR takes for ever to start up. It's driving me crazy! I only use it for internet and docs here and there. Any way to get it to boot up quicker?
View 10 Replies View RelatedMy brother has got an HP Pavillion dv9000 laptop. When he tries to start the laptop he gets a blue screen with the error message contained in the attached file. When I try restarting and pressing F8 to enter Safe Mode it just continues to this screen.
It started happening after HP requested that he download some new software to his machine. He did so and this problem started. It was a popup on the screen which asked him to install new software.
I am trying to troubleshoot it for him.
I have a Compaq presario V5000 series with windows xp about 4 years old. It has been running fine on wireless for years until a few days ago. I was getting a code 10 but now it doesnt even appear in the device manager anymore. Also, I still get resource conflict screen at startup. If I hit F1 everything starts up as normally but no broadccom!
Heres what I did so far.
Destructive recovery
reinstalled windows
installed updated drivers for broadcom and bios.
defraged
changed wireless card
I understand you can run off the adapter, But with the battery installed , i cannnot. If i plug adapter in like Iam charging it (not turning power on ) the light in front lights up just briefly then nothing. I also can't power laptop on. If i run the adapter with no battery in laptop everything works fine. What causes that? Just a bad battery? motherboard is new and so is the cord.
View 4 Replies View RelatedEvery time when i start my laptop HP Pavilion DV5-1050er i get an error "Application MFC STServices stopped working and was closed"
View 7 Replies View Relatedon my dv7-1270us I have noise coming from dvd drive at start.it is normal ?
because on my other 1175nr dvd drive is quiet at start
So I bought a sealed box 8530w off eBay. Now I know from previous HP business models that the warranty start date on the online lookup tool starts from the day the laptop was manufactured. This hasn't ever been an issue in the past, since I got previous laptops second hand anyway.
But this one is already nearly 6 months into its 3 year warranty. I guess it has been sitting around sealed in its box for a while.
So...
1. Is there any way I can get HP to update the warranty start date? (I'm getting an invoice from the seller as we speak)
2. Assuming I can, will that new warranty start date be reflected in the online lookup?
3. Will the new warranty start date be transferable if I sell the laptop, or will it only apply to me, with my name on the invoice?
My dv9843cl will not start, refusing to even go into BIOS, even though the screen turns on. This is suspiciously similar to what happened to my last laptop, and I suspect that a faulty graphics chip is at fault. I was playing Team Fortress 2 shortly before it crashed, and it was performing poorly, and occasionally making random colored boxes or random interference appear on the screen.
Unlike my last laptop, however, I'm not sure if there was a recall for the graphics chip, and since I bought the laptop in 2008 from Costco without anything other than the standard warranty, I'm probably not eligible for free repairs, right? -_-
I have had a HP dv5z w/ windows Vista Home Premium - 64 bit for two days now.
1) I have a wired USB mouse that I use since the touchpad is terrible. But everytime, I plug in this supposedley plug and play mouse, there is a message that says device driver is being installed and it takes a few moments before the mouse can be recognized. Is this normal?
2) Also, the day i got my laptop, i had to download Windows updates (the automated message on the control panel said so!) and installed them. I am not sure if its related but since then i have re started my laptop 2-3 times and there is a file check process that happens as a part of the start up and then just before the welcome screen comes, i get a message
Step 1 of 3 - Configuring Updates - Do not shut down your computer.
How long is this going to happen and is this normal?
will not boot up, just says "operating system not found".
went into setup, selected CD drive first, inserted winME Cd rebooted, but still get same error.
i've had this DV6000t (or dv6500) for quite some time. I believe i've had it since 2007, but really started using it a lot from 2009, running almost 24/7.
Here's the situation: I was playing a bit of Starcraft 2, and decided it would be fun to drop a dozen Terrain Ghost Nukes in an area. For those familiar with the game, you may notice a lot of lag when you do that. I didn't know it would lag like that until my computer abruptly shut off on me. Now nothing lights up except for the AC jack. I checked the vents, HDD, RAM, and other spots that may have heated up a lot, but nothing was really running hot. I'm familiar with how hot my laptop can be; the laptop was just 'warm' right after shutdown.
My guess is that I either:
-Overheated the laptop, which is what anyone would probably expect since HP Pavilions are well known for this, or...
-I may have had a power surge while I was playing.
So, I investigated my opening up my laptop to see if there were any physical damages.
It's hard to see with the blurry picture, but I actually think the chips didn't burn out. But i'm no expert with fried chips......
I have problem with dv9700t and bios F.59A. After upgrade bios from F.58 to F.59A and reboot, notebook won't start - there is only beep: first beep is long and other two are short. For me this sound show that is problem with graphic card. But from years notebook work fine and i don't use it to play games (only for office work).
So what can i do to run again my notebook?
How can I recover from a failed bios update? Is there a way to return the computer to the previous bios configuration?
View 3 Replies View RelatedProblem: black screen 3 beep at startup
Yesterday, I finished my work and hibernated my computer. When I came back, I could not turn on the computer. It goes automatically to a black screen and after 15 seconds I hear beeping noises. It's one long beep followed by 2 quickly beeps. Rebooting just repeats this process.
I went to the HP troubleshooting page and found this from my symptoms
[url]
It tells me that 3 beeps mean module problems. So i ended up testing both my memory sticks in a different laptop and they were fine. And I tested both individual pavilion memory slots, and still got the same 3 beep black screen on both. iif i was to have no memory sticks in, i still get a black screen but a different set of beeping noises, not sure if a laptop can run without memory sticks, but i figured i check)
Has anyone had a similar beeping noise black screen problem at startup?
I recently caught a virus after accidentally typing faceboo k. cm instead of faceboo k. com in IE but Avast was able to take care of it. However, after restarting my HP laptop, I was unable to go into windows and it says there's a problem with startup or winload(I forgot). I used the repair startup 5 times, but to no avail. (I'm not sure if the virus is the cause of my problem).
So, I decided to use the Vista recovery DVDs and reformatted the C drive. I put the CD and HP automatically reformatted the windows partition of my drive. After it's done, the laptop was restarted and a dialog box that says "Software is being installed" appeared and there was a progress bar. But, it restarted again before the progress bar has a chance to complete. And after the laptop is restarted, the system says "BootMGR" is missing please restart using ctr alt del. After I restarted it again, a dialog box saying the recovery has failed appear. I tried this twice and failed both. The details of the error say something about QFE is missing or something.
FYI, the last time I used the Recovery cd I was brought to a blue screen (if I'm not wrong) where I can repartition, delete, or create partitions before formatting the drives. This time, I was unable to repartition or delete the drive, I was brought straight to reformating. And I was unable to use the Recovery Disk in the system; I pressed F11 and nothing happened.
I'm more of a desktop user but my husband gave me this laptop on January 2007. Since then, I think I only used it for less than 20 hours (we don't have a wireless)... when we got out of town.
The last time I used it, about a year ago, it turned off by itself. I tried to use it again when I got home but the screen is just blank whenever I turn it on. What could be the problem? I don't think it's a good idea to send it for repair to HP as the warranty expired already.
when I turn it on, all the blue lights turn on... but the screen won't therefore I can't use it. Ealier, I hooked up an external monitor but didn't work. Could it be an LCD problem?
The notebook doesn't have any scratch or whatsoever. It still looks like new, yet not working.
I have been sent 2 system recovery dvd's and one supplemental disc by hp. I put them into my drive and nothing happens. How do I start this procedure? I thought maybe all that I hav to do was wait until it started automatically (didn't happen) or click on the Boot option - nothing happens there either. I Have an HP Compaq Presario CQ60 Laptop with Windows 7 home premium. What to do? I am NOT a very sophisticated computer user. I need to do the recovery as I've had a total crash.
View 2 Replies View RelatedI was about to do a factory restore on my computer later in the day, but i was unlucky that the computer stopped working When i turn it on it continuously beeps and won`t turn on, i have picked the option to `start windows normally` and even the option that checks/diagnoses the files (to fix the problem not letting me startup) but when it says `loading files` it starts beeping again and the process stops..
I also read that it `could` be a problem with the RAM, but maybe that was for a different problem or so, but if it is a problem with the RAM, then how can i fix it?
Laptop: DV6563cl (Intel Core 2 Duo T7300, 3GB RAM, 500GB/7200, 15.4 inch, Win 7 RC 64bit, 128MB 8400m GS)
I recently bought a 500GB/7200 RPM hard drive to my laptop and I decided to install Windows RC 64 bit. Before doing the hard drive update, I had installed the 7 RC 32 bit since it came out.
Now, I can't recall when I had the 7 RC 32bit that the laptop's fan was running on full blast after sleep/stand-by. It is also loud when you start-up the computer from a restart or after a shut-down. The fan speeds down to a quiet speed/rpm after...I'd say 2-3 minutes.
I installed everything listed on HP's website for my laptop (drivers and such after installing 7 RC 64bit):
[url]
I noticed that the Nvidia driver on HP's website was not a recent one, so I hopped on Nvidia's website to get a newer driver instead (186.03 I believe).
I have my laptop set to Power saving's mode and I only bump it to Balanced when I'm doing something heavy (like iTunes encoding, etc).
I did check to see if maybe my anti-virus program that's installed (avast...AVG didn't install when I went to 64) was doing scans or such, but it isn't. Well, actually I take that back...does avast do a very slow/quiet scan in the background? I see the HDD status light blinks steady, but when I pause avast, there is not steady blinking.
i got a hp dv2000 and sometimes when i start it up and it gets to the user selection screen i cant find my cursor to select my user account. I keep moving my finger on the touch pad but cant find it. I have to hold the power button down it will shut off then i have to pull out the battery start it up and the cursor is now there this has happened like 5 times already what would cause this?
View 3 Replies View Relatedits a powerbook 64 and when ever i start the pc up i get this msg
panic (cpu 0 caller 0x002de020: unable to find driver for this platform: "powerbook 5,6".
latest stack back trace for copu 0:
back trace 0x00095564 0x00095a7c 0x00026838 0x002de020 x002bd360 0x002bd118 0x002bdb80 0x002be1ec 0x00a9654
proceeding back via exception chain:
proceeding back state (sv=0x0051fa00
pc+0x00000000; msr=0x0000d030; dar 0x00000000; dsisr=0x000000000; lr=0x00000000; r1=-x--------; xcp=0x00000000 (unknown).......
I can't get my M1530 to start. When I press the power button, I just see the blue LED's cycle. Nothing shows up on the screen, no BIOS or anything. I tried putting a vid to show it .....
View 3 Replies View Related