Acer Aspire 5755 :: Unable To Boot To Windows 7
Nov 13, 2014
I have an ACER ASPIRE 5755 laptop with 4GB RAM and 500 GB Disk. Now the issue I am facing is, it doesn't boot up. It just sits at a screen for sometime and then even if we reboot it goes to the same screen which is much prior to loading Windows and I believe just after the POST. I checked in the BIOS that hard-drive was not getting detected. I unplugged replugged ..took it out, put it back in but nothing worked. Than I removed that hard-drive and replaced it with a working hard-drive of my fren's & eventually it booted up fine. Hence this isolates to be an issue with the hard drive. Now my question is that, "is there any upper limit on the size of the hard-drive (as the inboxed one was 500GB)". I am planning to take 1TB hard drive. So will that work In addition to this, is there any link provided by Acer which I can browse and check what all Hard-drives are supported / compatible / recommended by Acer. I have been a big fan of Acer Laptops from a long time and would not want to buy a new laptop just because of this simple hard drive issue.
View 1 Replies
ADVERTISEMENT
Jan 12, 2015
I have an aspire 5755-6699 that has been giving me problems. It keeps freezing up and going into windows recovery at startup. Windows recovery stopped at checking and fixing disc errors. So I bought a new hard drive and put it in and tried to restore it with the recovery disks. Everything went fine until the very end with the language disc. The top bar went to 100% complete and the bottom bar stopped at 99% and just stayed there. I tried to restart the computer but it says there is no valid disk drive. Tried running e recovery again and the same thing happened. What should I do?
View 9 Replies
View Related
Jan 27, 2014
I have a Western Digital 1TB USB 3.0 external drive. I am connecting it to the correct (blue) USB 3.0 port on my Acer Aspire 5755-6647 laptop which runs Windows 7 x64.
Upon connection, I get the "This device can perform faster: This USB Mass Storage Device can transfer information faster if you connect it to a Super-Speed USB 3.0 port" message. When copying files off the drive, I get about 32 MB/s, which corresponds to USB 2.0 speeds.
I have tried disabling USB power management in the USB 3.0 Host Controller Utility. I have tried uninstalling the device and reinstalling it. The cable I am using came with the drive and is a USB 3.0 cable. I have the newest Renesas USB 3.0 driver installed (2.0.34.0). I have also tried using an older Renesas driver. My BIOS is up to date (P5WE0121).
The first time I connected this drive to my laptop, it was on a USB 2.0 port (I had for some reason misremembered which side of the laptop had the 3.0 port and didn't check for blue). As I said, though, I've uninstalled the device completely. I suspect that Windows may be "remembering" the device and installing it with the 2.0 driver.
View 9 Replies
View Related
Mar 23, 2009
i just bought an acer aspire 5102wlmi without a HD for a friend. so i went and bought a HD and proceeded to install windows XP home service pack 2.
the problem is it constantly stays in a loop, i load and boot from the disc, it copies all the files, reboots, loads the files, says starting windows, and then just starts all over by going back to the setup screen. i've formatted the drive and made multiple attempts. had anyone else had this problem? if so what is the solution?
View 7 Replies
View Related
Nov 14, 2014
I have been unable to find the controls of the Webcam. Is the software already installed or do I have to download it? If so, what do I download and where do I find it?
View 1 Replies
View Related
Jan 27, 2015
On my new Aspire Switch 10 SW5-012 with Windows 8.1 I am unable to change the size of the onscreen keyboard. Microsoft cannot answer and refers to Acer support. Is there a solution to that?
View 5 Replies
View Related
Dec 15, 2013
my girlfriend bought herself an HP 255 G1 notebook which came a week ago. She ordered the version with Ubuntu pre-installed on it (not Windows 8). However, the pre-installed Ubuntu had a lot of flaws - the internet connection keeps disconnecting randomly, many updates cannot be installed, random errors keep occurring, sometimes the interface becomes unresponsive etc. Long story short; my girlfriend asked me to put Windows 7 on the notebook, as I am using Linux and have my old Win7 key unused.
So I prepared a Windows 7 USB stick, tried it out on my own notebook (works fine) and then tried it out on the HP 255 G1. The first couple times the USB stick wasn't recognized by the notebook. After fiddling around a bit, I have managed to get it recognized, but every time it is, the screen goes black and starts flickering.
I have tried turning Legacy mode on and off but to no avail.
I have read that this might have something to do with "UEFI", although I am not sure what that is or whether it's really related to my problem.
The very first thing I need to know whether it is generally possible or not to install any kind of Windows on this notebook, because if it's not, I will have to hurry to return it quickly.
Here are the system specs of the notebook. I am using a FAT32 formatted USB stick with a 64-bit Version of Windows 7 on it.
View 9 Replies
View Related
Sep 30, 2014
I have an acer laptop e1-571 with windows 8. the mb failed ordered a new one installed it. on boot now i get no bootable device. The bios shows the hard drive and its the first in the boot order. If i hit f12 after powering on to access boot options the 3rd choice is efi device windows boot manager. If i select that it boots normally and runs fine. is their a way to boot the machine without having to hit f12 every time and selecting efi device to boot to windows? i tried updating the bios as well.
View 2 Replies
View Related
Apr 1, 2014
I burned two ISO files(Memtest86+ & latest DBAN 2.2.8 CD bootable ISO software ) onto two different blank CD-Rs on two different ocassions by using the in-built Windows burner in my system, also used Cyberlink ISO file burner/Mount as Virtual drive.
Tried booting from CD by following Step 1 to 4 given in this MS link . After that clicked Select a USB Device, then boot from Internal DVD/CD Drive, then OK. It took some time to process & after that I got this screen:
When I entered BIOS Setup clicking F10 and there on Boot Device options, I got this screen:
I'm not able to understand why I can't boot from any CD.
View 9 Replies
View Related
May 14, 2014
I have an ENVY 17 (3277nr) with windows 8.1 in it but I'm unable to update it since several months ago so I decided to reinstall the OS so I went to the windows site that lets you download an ISO image of windows 8.1 to burn it into a disc (right now I dont have a 4gb usb at hand but is also possible).
I already burned the disc by right clicking the ISO and selecting 'burn disc image' and changed the boot options but every time I turn on my computer all I see is a single underscore and then the regular windows 8 boot screen.
I already visited wbesites in this regard and I've read things like the windows 8 UEFI thing (not on my laptop since I've upgraded from w7) and the security settings on the BIOS but none of them seem to fix the problem.
Additional details:
Oddly, when trying to open the burned dvd it only says 4.37gb out of 4.37gb, do you think my dvd drive might be damaged?
View 3 Replies
View Related
Aug 13, 2014
HP 1000-1327TU Notebook running on windows 8 (64 bit) chinees. actually my brother purchased the HP 1000 laptop in china and gifted me , it is running in chiniess language operating system . iam unable to change the language to English so i decided to uninstall win 8 and install win 7 .but unfortunately it is not booting from cd , how to install win 7 in this laptop
View 3 Replies
View Related
Jan 31, 2013
I own an Inspiron N4010 14R dell laptop. When I restarted my laptop yesterday, i couldn't boot into windows and windows logo was rotating forever. So I thought OS was curropted and tried to reinstall OS. But it also didn't work. I couldn't able to install OS. But I could able to delete a partition and refresh it.
Then I ran a diagnosis on my computer and it showed an error code 2000-0146. (saying HDD needs to be replaced)
I called Dell support center and asked them about the issue. They said my hdd nedds to be replaced. So I bought a new 2.5" SATA seagate hard drive and installed it in the system.
But even after that, the same problem exists. But this time Diagnostic doesn't show any error. My warranty period is void.
View 1 Replies
View Related
Mar 7, 2014
Dell XPS 12 Laptop.
Symptoms: Unable to load windows 8, unable to load windows repair, Unable to load windows 8 installer DVD, unable to boot into Linux, Unable to load Linux live CDs or USB sticks, unable to even use an MSdos boot USB.
Problem just appeared one day, one month out of my 1 year warranty so I began troubleshooting myself. After replacing the SSD, Motherboard, and unplugging every single cable, even disassembling the display and disconnecting the Windows button, Webcam, and touchscreen cables. Still I Could not get any OS to boot. On a whim I powered on the laptop them promptly disconnected the daughter board and sure enough my OS booted right away. Upon further inspection I learned that the Auto-rotate or rotate lock button had become stuck/damaged due to a fall or hard bump. I ripped off the button and ordered a new daughter board online and all is well now.
View 4 Replies
View Related
Sep 24, 2009
I installed Windows 7 Home Premium 64-bit on my Acer Aspire AS1410. Maybe it's normal, but the hard drive LED is solid on for about 30 seconds before it boots into Windows 7 during the floating windows screen. Is this normal?
View 10 Replies
View Related
Oct 29, 2014
I just buy an Acer Aspire V3-371, then I delete all partitions in HDD and install MS Windows and driver for this notebook. Everything are OK until I ugrade BIOS form v1.05 to v1.08. Now, it cannot boot to MS Windows and shows me "No Bootable Device".
I try to reinstall MS Windows, but I see a notice "Windows can't be installed on this drive" with details "Windows cannot be installed to this disk. The selected disk has an MBR partition table. On EFI systems, Windows can only be installed to GPT disks".
View 5 Replies
View Related
Jan 5, 2015
ASPIRE 5251-1513 with 2 - 1GB memory sticks in it. The problem is after updating with microsoft updates and changing the useable memory setting to 0 Windows 7 will not start up.. so I tried to restore from earlier restore points. Windows 7 home premium still won't start up. I tried using the windows automatic repair, it fails after a few minutes. I tried resetting the BIOS to system defaults. Windows still won't start up.... says windows start up, but after a minute a black screen flashes and laptop shuts off. I don't have any recovery disks.
View 4 Replies
View Related
Nov 6, 2014
I have a Lenovo Y410P that will not boot. The BIOS only sees to PXE boot. It does not attempt to boot from the Windows 8 installation disc, or from the hard drive that I reinstalled Windows on myself. I can boot to both of these on other computers, so I know they are not the problem. I'm thinking it's BIOS or motherboard related, but I'm not sure where to go from here.
View 2 Replies
View Related
Nov 21, 2014
So I bought Acer E5-527G-77BU. I installed windows 8.1 Pro with no problem. But I really don't like this windows and I want to install Windows 7. But when I plug in DVD or flash drive with windows, I don't get the boot option for it (in the f12 boot menu). If I put in the Win 8.1 DVD everything is fine. I can chose it from the menu.
View 3 Replies
View Related
Oct 13, 2014
Acer E5-471..... When I attempt to start my laptop it goes to the Acer logo screen and will not boot Windows 8. Only black screen and mouse pointer appear. How can i fix it?
View 3 Replies
View Related
Oct 31, 2014
When I strart my laptop it will show the Acer screen with the F2 F12 options then goes black with cursor in upper left corner and when windows should load it goes back to acer screen and will keep doing this till I smack it on the side then it will load windows and run normally. I created a disk image, bought a ner hard drive, loaded my image onto the new hard drive and it worked fine for a couple hours of starting and shutting down. Then it started doing it again ...
View 2 Replies
View Related
Nov 20, 2014
My Acer Aspire L5100 , now can not start windows.
Blue screen , boot manager status Oxc000000f
needed unit is not available.
I do not have the win disc, what to do now?
View 3 Replies
View Related
Oct 31, 2014
When I strart my laptop it will show the Acer screen with the F2 F12 options then goes black with cursor in upper left corner and when windows should load it goes back to acer screen and will keep doing this till I smack it on the side then it will load windows and run normally. I created a disk image, bought a ner hard drive, loaded my image onto the new hard drive and it worked fine for a couple hours of starting and shutting down.
View 2 Replies
View Related
Jan 31, 2015
Tried to do a restore to factory image... Got error code 0x241... Computer is hung up at Windows Boot Manager, going around in circles... Can't accomplish tasks on windows boot manager and can't get out of window...
Acer Aspire One
Windows 7 OS
Have recovery data on a flash drive
View 2 Replies
View Related
Feb 19, 2015
My daughter's Acer is 2.5 years old and it's running Windows 7. She recently rebooted it last week for a Windows Update and since then it starts up but hangs, with the hard drive light blinking slowly. I ran it in Safe Mode and it gets through CLASSPNP.SYS then hangs. According to articles this is usually a hardware problem. The only option I have with this OS is to bring up the Command Prompt. I've tried System File Checker - no go. System Repair comes back with unknown error and what looks like a bad Driver.
I was able to build a new partition (100+GB) and do a clean install of Windows 7 x64 Ultimate w/ SP1. This went through fine, though I would have to load the Acer drivers for the network card, etc. to finalize it. The point here is that this shows that the hard drive isn't the issue.
My fear is that Windows installed either some sort of driver or other update that has now caused the current OS on her laptop to be unusable. I went to do a System Restore and the only restore point it had was the Critical Update that she rebooted to on 2/13. Trying to roll back to that Restore Point didn't work.
View 5 Replies
View Related
Jan 14, 2015
I have an acer M3 581T which I bought about a year ago. Now, windows crashed and said there was a file missing. I am no longer able to boot up the system, I've tried the erecovery (alt f10) but it just proceeds and says it's not able to boot. I have no recovery cd/usb at hand. It is of my understanding that this ultrabook has two harddrives. One SSD on which the operating system is installed and one HDD with the other files on.What do I do to make it work again? I do not care if all my files are lost.
View 9 Replies
View Related
Oct 11, 2014
I have a Acer E1 522-3657 computer, which my son set-up for me but did not make the recovery disc(s). The unit is just outside of the warranty period when the hard drive failed. The hard drive just makes a clicking noise and after the logo screen appears it goes to a blue screen with a box that has the following message with in, "Default Boot Device Missing or Boot Failed. Insert recovery Media and Hit any key.....Then Select 'Boot Manager' to choose a new Boot Device or to Boot Recovery Media.
I have installed a brand-new Western Digital 1T Sata3 harddrive to replace the Toshia 750 GB original Drive. After turning the computer on and at the logo screen I press and hold F2, this takes me to the InsydeH20 Setup Utility Screen. I see under the "Information" menu that the installed harddrive model and serial number appear. I see in the "Boot" menu, Boot Mode: "UEFI" and Secure Boot: "Enabled".
Under the "Exit" menu, Exit Saving Changes is highlighted. When I press F10 a "setup Configuration" box appears asking to save configuration changes and exit now? "Yes" is highlighted to which I hit Enter and are returned to the "Default Boot Device.......page. I then hit ecs twice and are at a black screen with the message No bootable device -- Please Restart system_appearing in the upper left corner of the screen. I then push and hold the power button until the computer shuts off.
I have ordered from acer the "Acer E-recovery Media Disc Set", which is specific to the SNID of my computer. I have not attempted to format the new hard drive in any way. I assume the E-recovery Media Disc Set will handle that operation due to the multiple partitions required.
In view of the above situation, do I need to set up the computer in any way before I start to utilize the E-recovery Media Disc set. I assume the Media will be on CD's. The computer was running Win 8.0 which was updated to Win 8.1 and was running very well, very stable.
View 5 Replies
View Related
Feb 6, 2015
Acer V5, spilled coffee on keyboard. no problem at first, then lockup, and on restart get the No Boot Device or Boot Failed. Am using my old laptop now. Can I get a download, save it to thumb drive, and use it to restart/reboot my Acer?
View 2 Replies
View Related
Nov 22, 2014
how can i open the cd drive on my acer aspire e15??? when i open the cd drive (D then says it came to a problem what must i do???
View 2 Replies
View Related
Sep 23, 2014
I had to buy the recovery disk for my Aspire V5, when I start I change the bios to UEFI with secure enabled, then I use the disk Recovery System, once that I´m in the Acer Console Management, and I Selected the restore full, a pop up came with the message "Please Change your bios to Legacy¨ so I click on the exit button, and I enter to the bios and select the legacy mode, then the acer console management starts and says that the systems recovery fails because this is only for UEFI mode. So I dont know what to do, I have another 4 disk for the recovery but none of this is a booteable disk. Also I tried with UEFI and boot secure disable and same result .
View 1 Replies
View Related
Dec 4, 2014
Since getting my new v13 notebook. Problems with unable to search for wireless router . Wifi icons not out at time. Have to restart few times to be able to have the search for wireless device. When able to connect, notebook will hang upon surfing net. Notebook always hang and have to press off button to restart.
View 3 Replies
View Related
