HP/Compaq :: DV9000 Dv6000 Motherboard Replacement
Sep 10, 2009
My friend has a dv9000 laptop, and gpu on motherboard is dead, so he has to replace whole motherboard. I was looking through ebay and i found one silly thing, i can see that some motherboards are used for DV6000 series and also for dv9000. For instance 441534-001 motherboard can be replaced and used on bought laptops. So my question is are all motherboards replacable or just few of them as one mentioned above? We were thinking of buying one with intel cpu, cause now he has AMD.
View 4 Replies
ADVERTISEMENT
Jan 23, 2009
I bought a dv9000 about two years ago and recently the motherboard died. Since I'm not exactly rich at the moment I haven't bought a new laptop, but instead my father gave me his dv6286 because choose to upgrade.
But the geforce 7200 in the dv6268 isn’t any good for gaming, so I though if it was possible to take my geforce 7600 from the dv9000 and put it in the dv6286.
View 4 Replies
View Related
Jun 18, 2009
HP has identified a hardware issue with certain HP Pavilion dv2000/dv6000/dv9000 and Compaq Presario V3000/V6000 series notebook Read more at their site[url]
I had put the link in another thread; But i didnt include the series numbers of those affected.I ran the #'s in this sites search engine and came up nill .So now its "out there",.
View 15 Replies
View Related
Oct 24, 2009
my dv6000 has a common problem, it just wont turn on anymore, it's starts up and shuts down with in 5 seconds and repeats until i turn it off - i'm gonna either strip it for parts or sell it as seen for spares/repair.
Two questions if you'll indulge me - is this the motherboard that's gone? Most pages online suggest this and getting a new motherboard is expensive and likely to go again i think. Secondly do you guys know where the bext place for new to try and sell it for spares is and what could i possibly expect from it with a bad mb?
View 10 Replies
View Related
Oct 10, 2009
regarding purchasing a new motherboard for my HP DV6189eu laptop. The original one went dead with no screen and no bips at boot...
I know from some research that is common of that model of gpu (7200go) to die like that. So I am heading towards buying a motherboard with a different graphic chip, like a Intel one.
The original motherboard is spare number 443774-001. My main question is if I have to be careful in buying a new motherboard or just a new one for the same DV6000 series model with AMD socket is enough?
View 10 Replies
View Related
Oct 10, 2009
I know that the dv6000 is one of the worst laptops but I still tried to repair it and got a new motherboard.
Initial problem: fried motherboard.
Got a refurb one off ebay now my issues is as following:
Press the on power button, fan spins for 2 seconds and computer remains on with no boot posting. Hard drive light is OFF and I can't hear the harddrive but I don't think it is the hd because I should still be able to access the bios and monitor should still light on. screen doesn't display anything. cd drive works and when I put a cd such as a windows disc you will hear it work for a couple minutes.
I tried everything from resetting the power cycle, removed the memory, harddrive, connected an external monitor, changed the little battery inside the motherboard. all power cables and ribbons are connected. keyboard won't respond though (fn light wont light on and ctrl alt delete produces nothing) ! I hate HP. after opening the computer I realzied what a piece of junk.
View 3 Replies
View Related
Sep 9, 2009
to start off I updated my vid drivers to the most recent nvidia driver and it has been downhill from that point! When i boot up it shows bars on the screen and will not load windows so i shutdown and load using safe mode which starts right up but still has red artifacts on the screen, i then uninstall the nvidia driver and reboot windows now it loads up properly still has the red artifacts though. So now it is using a standard vga driver then i install a different nvidia driver and get the same problems
I fear i may need a new mboard, would i be able to fit a better mboard/gpu in this chassis if it turns out my gpu is dead? think this may fall under a recall or something?
View 10 Replies
View Related
Mar 3, 2009
Where can I purchase replacement parts for the dv5t motherboard without spending an arm or a leg. I spilled coffee on the and now it's pretty much toast. It won't even start up.
View 10 Replies
View Related
Feb 9, 2009
After some issues i had with my GPU, Dell agreed to replace both my Heatsink and Motherboard, and i wanted to ask those who have had replacements in the past; has anything changed since july 2008? (when i bought my m1530)
have they improved the heatsink, or even changed it? ( i got the aluminum one, crappy piece of engineering right there )
and im sure the GPU issues are still present, but do they run cooler now ?
im asking this because in July the "defective Nvidia GPUs" were still in the dark, and the news about them was a mere rumor...
View 10 Replies
View Related
Apr 22, 2010
I am getting my 1640's motherboard and lcd screen replaced tommorw (dell are taking laptop into the centre). I have the 512mb Ati card, I understand the new motherboard has a 1gb card.
What are the chances I will get the new motherboard and hence the new card? Or will they still have the old motherboard replacements?
View 5 Replies
View Related
May 26, 2010
My 6920G went down a few days ago, I sent it to local computer store to have it diagnosed. It turned out that they say it is a mobo issue and said that it would cost aroun 400 to get a new mobo + labour fee.
I don't have any warranty on theis laptop, and the 1 year warranty by the manufacturer has expired. I am just wondering if I can order the mobo fron Acer and maybe replace it on my own.... I don't know which would be better, to have the guys at the store do it for me or phone Acer....
View 10 Replies
View Related
Mar 10, 2010
After a completely useless representative walked me in circles, then called me back once we got disconnected and left a 3 second message full of background noise I decided to go ahead and try out another representative.
This one was more useful, I told him about how the computer was underclocking when I was playing games and was running hot in general, and he suggested that we replace the motherboard, heatsink, and fan assemblies.
I had read about a power adapter possible being the issue but that wasn't offered so hopefully this first major surgery allows me to play games again
View 5 Replies
View Related
Oct 31, 2009
I have a 1 year and 10 month old Acer Aspire 9300 laptop and the motherboard recently bit the dust. My retailer in Gananoque Ontario could not find a replacement. I called Acer which took forever to get to someplace where I could leave a message. I received no reply. After you've called once it's impossible to call again. I guess their answering machine recognizes my phone number and then asks questions that makes it impossible to get through. I sent a detailed explanation of my problem by email 3 times asking a few simple questions, the most important being 1) where can I send the laptop to be repaired? 2) do you sell replacement motherboards and if so how can I buy one? Am I asking too much or getting too technical for them? I've been trying for several weeks now to contact Acer to no avail. What kind of an idiot company is this? A techie put me onto a company called Grand Tech in Richmond Hill Ontario that can replace the motherboard on an exchange basis but the replacement will likely be a repaired one.
Someone told me that the problem I have with the motherboard is common and it is because the solder used at least when mine was made was of poor quality. I hope that problem has been resolved. I'm afraid a repaired replacement my have the same problem. Some people just say to trash it and get a new on which I did. I bought a Dell Inspiron 17 which is supposed to arrive on Nov 11. I would however like to repair the Acer if it can be done cheaply and use it to replace my 8 year old PC in the rec room.
View 10 Replies
View Related
Sep 24, 2009
Well, my Nvidia 8400 died for second time and I called Dell to replace it. After asking for a sustainable solution and to ensure me that I won't have the same issue once more, they said that they will install me a new motherboard revision which reduces the possibilities of having my GPU dead.
Thus, they replaced the motherboard. I didn't format my system but kept my Windows Vista Ultimate x64 installation.
After using the system for a couple of hours I realized that the system was under-performing. Then I checked with CPU z utility and found out that the CPU clock was stuck @1,6GHz (although my power scheme was high performance). My processor is the T7500. The system was overheated and the clock speed was reduced (I guess). The thing was that I could almost do nothing, not even surf on the internet. This makes my laptop unable to deal with applications that need lots of CPU power.
Does anybody else face the same problem? Is there something I could do to return to the old situation? Should I contact Dell and complain? It is a huge problem cause half of my applications cannot be used any more!! After a few minutes of use the laptop stops performing normally!
Could it be that if I format my HD and make a fresh install the problem will be resolved? (I repeat that I didn't format my system after the MB replacement).
View 10 Replies
View Related
Sep 24, 2008
So My M1330 was part of the defective batches of Nvidia Video card. A dell tech guy came and replace the motherboard and also a defective battery. I assume that the hard drive would work the same and I assumed I didn't need to format. My current hard drive was just taking forever to boot up, and was just so slow. I figure i needed to reformat.
I used a new 320GB hard drive i was planning to replace the current drive with. Now that its fully formatted. It's still unbelievable slow. I though the speed step might not be working current but i used wcpuid to test the current speed and it was at full speed. Though the system doesn't seem hot at all. I just cant figure out why its so slow. bios is currently at A12 which is the lastest
View 10 Replies
View Related
Nov 25, 2009
I used to use my eSATA port every day with a few different devices. I started to have an overheating problem, so Dell replaced the motherboard and graphics card yesterday.
Of course, that means I lost all my BIOS settings. I'm pretty sure I have them back to where they should be (RAID mode on the SATA controller, eSATA port enabled), yet the eSATA port doesn't see a damned thing connected to it.
Every other piece of hardware is exactly the same as it was before. Any ideas as to what I might be missing?
View 6 Replies
View Related
Dec 1, 2012
I just replaced the motherboard in a Dell Inspiron 1440. The last step in the Dell Service Manual is to enter the correct Service Tag within BIOS. When I started it up and hit F2 and the section with the service tag could not be changed. Is there another way of changing the service tag to the correct one.
View 8 Replies
View Related
Oct 21, 2014
After replacing the fan, I have a power up issue with the laptop. Basically, the laptop will only power on with the power cable disconnected at the motherboard. It was by mistake that after the fan was replaced and everything was put back together, that I noticed that the battery was not charging.
Â
I then reopened the machine and reconnected the power cable to the motherboard and nothing - no power.
Â
When plugging in the power source with the battery in place, the LED adjacent to the power socket lights up WHITE then stays ORANGE and will not power up. No other lights, no fan noise, nothing.
Â
If I remove the battery, the LED adjacent to the power socket lights up WHITE and stays white however will not power up either. Same agin, no other LEDs, not fan noise, nothing.
Â
I have now opened the machine back up and disconnected the power from the motherboard. Put it all back together and the laptop powers up as normal with the battery and it works fine. (Well until the battery runs out anyway).
View 3 Replies
View Related
Mar 2, 2009
My friends HP just died today. It seems like the GF8400GS went busted. She's out of warranty so we need to find a solution. It seems like HP put their proprietary design GFX card inside their laptops.
View 10 Replies
View Related
Apr 14, 2010
Have a dv6000 with turion 64 X2 tl56 and 2 gigs ram. Running the latest F42 BIOS. Is this thing compatable with Win7 x64? It should be, anyone tried?
Lastly, is it confirmed that 2MB sodimms will NOT work on this thing? I'd like to upgrade, currently have 2x 1 GB sodimms, would like to try 2 GB sodimms if it would recognize them.
View 3 Replies
View Related
May 31, 2010
searching for the best spec'd DV9000 gpu, but my search results always just show up the overheating problem... does anyone know if there is a list around with all the different options of DV9000's? I currently have a 7600 go GPU, and I just bought a DV9000 mobo for $3 with a 7900 go GPU on it. As I can get them fairly cheap if I'm lucky, I want to find out what is the best GPU available on a DV9000 system board.
View 4 Replies
View Related
May 4, 2009
I had a friend bring me her HP DV6000 telling me it won't boot.
When the power switch is pressed, all the lights come on for about 4 seconds, then go off. The screen never initializes.
I have noticed that touching the pad near the on switch/speakers will have the same effect.
I popped the switch panel and it looks to be plugged in and all the wiring intact.
I borrowed a known good battery and charger and it makes no difference.
The existing battery and charger work fine in the other DV6000.
Is it possible I need a new switch or cable? or is the mainboard toast?
View 3 Replies
View Related
Sep 12, 2009
i was using my hp dv6000 laptop and tried to open a video file my system got rebooted instantly and after that I saw a crashed boot screen (HP logo was all distorted, vertical lines on that). Any way i went to the safe mode and uninstall the nvidia drivers, now its working fine with default windows vista home vga driver but the boot screen is still distorted. When i update the nvidia drivers the laptop refuses to go inside the windows.
Have to go to safe mode uninstall the driver and it starts working on default vga drivers.
View 10 Replies
View Related
Nov 12, 2009
A friend of my g/f gave me her computer to fix. She said she took it to Best Buy and they said her HD is messed up. Now, if I order a new drive and the restore disks from HP, will that fix this issue? She is not worred about losing any data. Is my thinking correct? Install new HD, put in restore disks, start it up and follow the directions.
View 9 Replies
View Related
Sep 10, 2009
I bought an HP Pavilion dv6000 with a problem on the screen, I have less than half the screen at the bottom with a dark line where sometimes changes color or simply it removes and looks normal I have no problem with the rest of screen,
View 4 Replies
View Related
Jan 28, 2009
Device Manager doesn't recognize my CD rom. Sometimes it's there, but mostly it is not. When I insert a disk it starts and then stops and doesn't read.
View 4 Replies
View Related
Jun 23, 2009
hp pavilion dv600. when u press the power button it will sometimes restart three times before displaying the hp start up logo and sometime it starts fine it does the same thing even if the hdd is out or cd drive is out or if the battery is out or if the RAM is out?
View 10 Replies
View Related
Sep 14, 2009
i just took apart my laptop yesterday to change my cpu on it. i was running T7500 and changed it to T8300 and man.... that T8300 is so cool. with AS5 my idle temps are down to 25-27*C thats a HUGE jump from my old T7500 which was a mini baking oven.
but anyways.... it took me 3 hours to take everything apart watching videos videos on hp.com but onc ei took it apart, i looked at the HSF and man its one of the weakest hsf i've seen. the only part thats copper is just a tiny square base thats on top of cpu. everything else is crap. and there were some pads on the end of the hsf to i guess cool the little things on the side. (forgot what they were called) i wanted to apply the AS5 to all the places that the pads were touching, but that part of the HFS was not copper. i'm not sure what it was.
i'm sure everyone that ever replaced cpu on the DV9000 had taken the whole laptop apart... have you guys ever thought about replacing the HSF with an aftermarket HSF thats better than the stock? i tried searching and found none that were any better than the stock. none of them are all copper.
and i did not want to put AS5 on the other things that has that white/beige pad on, since the bottom of the HSF looked weak and i did not want to fry the chips/what ever the pads were supposed to cool... can you guys help me find a better HSF for the laptop? or that stock crappy hsf is the best/only thing for me?
View 10 Replies
View Related
May 21, 2010
I have installed Intel X-25M SSD with Windows 7 Ultimate in my old dv9000 (CD, 1 Gb RAM), and it is quite a disaster. The laptop is getting hot, installing programs (Portal from Steam) results in 90 C on the processor and a shutdown...
I use RM CPU Clock to lower CPU multiplier from 13x to 6x (it works on my HDD and Windows XP, I don't have issues), but on SSD it won't help much.
Browsing: 70 C
Installing software: up to 90 C and sometimes a shutdown...
Playing games: up to 80 C
View 10 Replies
View Related
Jan 3, 2010
It all started when my dv9000 stopped detecting the DVDRW drive, i tried the same optical drive on a friend's laptop and it worked perfectly. I decided to go for an external DVD drive. After a while it stopped booting from the secondary hard drive (primary hard drive had crashed, so i installed vista on the secondary one). It detects the HDD, but it does not boot from it, the HDD is not even listed in the boot media list when you press f9 button at poweron. So i decided it was time to upgrade the bios, i entered my product number at the hp website, it gave a dv9627 as my model, in the bios its listed as a dv9500, so i downloaded the bios update for dv9500, boot from bootable USB Drive and did the upgrade. From then on my laptop never came on again. I found out about the crisis recovery tool, got a usb floppy drive, created the recovery disk, removed the battery held down the win + b first, plugged in power, powered on, left it for around 15mins, nothing happened, tried fn+b still nothing. The laptop screen just flickers once when i press the power button, power led on, hdd led comes on and then goes off, media button led are all on, other than that no sign of life, but the processor gets alittle hot so i suspect its still functioning. I really need help, i believe the bios can be recovered without sending the laptop to hp. I'm a student running on a really tight budget.
View 10 Replies
View Related
