My puter got messed up and I booted my delta OC'd card into Shitsta for 2 hours. and then decided to go back to XP.
my card died.
I still have a fx2500m but am lookin @ a fx3500.
Is the fx3500m HDCP compliant like the GTX?
I am going to get the Sony Vaio FW series with blu-ray.
I have a 2003 Sony RPTV, model kp-46wt510, with DVI port. Obviously this TV is too old to be HDCP compliant.
HOWEVER, I am not planning on using the TV as an extended display, just cloning the laptop main display onto the Tv screen like I already do with my desktop with DVI video card. I want to do this same setup with the laptop but the question is- will I be able to play my blu-ray DVD's or will I get the copyright protection screen?
I have a HDMI to DVI cable, and I am going to use the headphone jack for sound (mini-jack to RCA black/red)
I know that Apple did not include any HDCP support in their notebooks. As I understand it though, HDCP is an actual piece of hardware on the graphics card. I'm guessing Apple uses the same graphic cards as everyone else, but their drivers simply don't support HDCP.
Now that Nvidia has released drivers, I'm wondering, is it possible to update a Macbook Pro's drivers with Nvidia drivers and enable hdcp?
I don't know if anyone here has noticed, but there have been a crapload of FX3500s going for around $150 recently. There are still a few up for auction. You just need to look under "fx3500" when you search. Sure, they are used, but they are stated to be in working condition.
I was going to get one myself, but it would be an incremental upgrade from my 2500, and I didn't think the hassle of buying one and installing it would be worth rolling the dice for a slightly higher OC. Plus, the guy has good feedback, but nobody had given feedback for these particular cards last time I checked. This is important because the guy can't seem to get his part numbers right. From the information I have, the CG129 and YF209 (both of which are given in the description) are the FX2500 and 7900 GS, respectively. I would want to be sure I was actually getting a 3500.
I have Dell inspiron N4050, I was attempting to install a fresh copy of Windows 7 Ultimate and after installation, it restarted I get an error blue screen that reads: A problem has been detected and windows has been shut down to prevent damage to your computer. If this is the first time you've seen this stop error screen, restart your computer. If this screen appears again, follow these steps: The BIOS in this system is not fully ACPI compliant. Please contact your system vendor for an updated BIOS.
Technical information:
*** STOP: 0x000000A5 (0x0000001D,0x00000000,0x00000000)
I have just installed a fx2500 in my M90 and was wondering if I flash it with the Fx3500 bios would it become a fx3500? It seems from the specs that the only difference is the core/memory speed.
View 12 Replies View RelatedI can't get ati tool to run in vista64, so would really help me if i knew where the realistic ceiling lies
View 15 Replies View RelatedI just bought an Acer computer, and am to the point where I am about to return it for a MAC because I cant turn off the tap to click feature. I have tried going through the control panel and messing with the mouse settings. I have tried to install the elantech driver as well as the synaptics driver. I can't get the drivers to actually work. I have contacted Microsoft and they are basically like "we don't know so go ask Acer."
View 2 Replies View RelatedI've been trying to find these cards for a while.. I've been searching for "dell FX3500", "FX3500", "FX3500M", same for the others, etc.
I can't find these cards for my 9400.. There's a lot of 7900Gs, but that's the card I already have!
Are there specific codes for those parts? I know the 7900GS is DG008, but I don't know of any for the cards I want.
Even with Crysis winning the latest "Hog of the Year" award, it does have a decent GPU benchmark tool.
Please post any benches you've accomplished using the Crysis GPU Benchmark. I will post additional FX2500 OC numbers as time permits.
I also have a FX3500 inbound, so I'll update my post with that data as well once installed.
FX2500 [169.04 NBF MobileForce Drivers, All Medium Settings, No AA]
1024x768, Stock Clocks (500/600)
Min/Avg/Max
17.86/31.79/46.45
1024x768, OC 550/650
18.14/33.71/50.28
1440x900, Stock Clocks
11.51/21.41/31.68
1440x900, 550/650
12.55/23.46/34.22
1920x1200, Stock Clocks
8.48/14.37/20.93
1920x1200, 550/650
7.91/15.27/22.14
I'm on Windows 7 64 bit and the Microsoft ACPI-Compliant Control Method Battery device is causing my Aspire E5-551 to freeze. If I enable the device and I try to run my laptop on battery it freezes, but when it's disabled I can run on battery perfectly fine.
Now I don't mind having it disabled since it fixes the problem but when I disable it then I have no way of telling how much is left of my battery.
This is a brand new laptop, a little over a month old so I haven't done any damage to it. I sent it in to get fixed but when I received it back from the Acer repair center all they did was re-install windows which did actually fix the problem for about a week but the problem came back.
looking to push my overclock past 700mhz now since my gpu is going to be getting a custom fan and copper heatsink. Whilst experimenting I found that past 700 the temperature no longer matters, the voltage simply isn't high enough. But I don't know of any software way to change this...
Anyway I can get it above the 1.32V for the gpu? looking at maybe 1.38-1.4.
Besides that if temperature even became an issue I'd experiment with liquid nitrogen, which being a chem student I can get pretty easily . It's a lot of fun to play with.
what is the stock gpu/memory clock on the geforce go 7950 gtx for the 1710?
View 13 Replies View RelatedI am getting ready to pull the trigger on a 1710 within the next week or so. Yeah, I know the 1730 is coming out but I really can't wait much longer and besides, the 1730 is by far one of the biggest and ugliest models I have seen Dell come out with. Sorry for that little rant but anyway, back to the main question:
There is a $350 price difference between the 7900 GS and the 7950. I have searched the forums and found a couple of relavant threads but I wanted some people who own both of these models to readdress this issue and let me know if you like the model you have or do you wish you would have gone with a different GPU.
I have done a fairly big search on these forums, and everything seems to be pretty vague as to what drivers to use on a Geforce Go 7950GTX with windows vista.
Does anybody have a direct link to the best drivers available?
can some 1 tell me wts the temperature for the M1710 with 512 MB 7950 GTX please ,,cause i just upgrade to it and i dont now whts gonna be and please tell me which program (am using 2 programs I8KfanGUI and NVTemplogger)
View 10 Replies View Relatedi'd like to know what kind of temps to expect from a normally working card.
What are your temps on idle (normal room temp 20c-30c)
and what are the max temp it reaches when say we run the ati tool graphical view. (Just for reference - when idle, ATI Tool reports 65c on my card, and after running the 3d view of ati tool the card will reach 104c).
I'd like everyone who has that info to post it here and i'll do the math and calculate the avarage working temp of that card.
Since different monitoring progs report different tempratures please state which program is reporting the temps.
I know this as been covered a millions times but I can't seem to find a straight answer. But I am trying to figure out my actual temps on my overclocked 7950 at 650/800
Using I8kfangui my temps are 59 to 82c with out any temp offset
Atitool temps are Identical 59 to 82c
Nvidia Mview is the same 59 to 82c
Now I though there was an 8 degree of set for I8kfangui, but its running the same temps as everything else is this my actual temps or there still an 8 degrees offset making my temps higher?
I'm just about to pull my dead 7950 GTX and send it off for repair ... they say they found the problem with this card failing and have a unique fix so we'll see. They are on Ebay if intersted.
Anyhow, I would like to replace all the thermal pads with a good thermal compound ... I was looking at IC7 synthetic diamond.
I am more than capable just never done this with my XPS M1710 so I need a guide. Question is, can all of the thermal pads be removed and replaced with IC7 or is the 1/32" gap between the memory and heatsink too much? I have read that you can fill this gap with pure copper shims but haven't found any details.
I have Inspiron 9400 with 7900Gs card. I have 9 cell battery. I have ordered 7950GTX, 4GB of DDR2 and also 130W power pack. Is there anything I need to install and use this card? I had a look thru the forum but I couldnt find any information how to instal this paticular card and what sor of BIOS will I need for the card and the laptop.
View 11 Replies View RelatedI have xps m1710 with 512mb 7950 gtx,2 gb ram,2.33 core due
I have some strange picture coming in my lcd some times,so can u tell me if my video card on the way to die,
also it happend a few times with Ghost recon advanced warfigter 2 during the game but if I press Alt+Esc to go to the windows thats strange picture dissapers and then I can go back to the game,its allways happen with the game but only 1 time with my windows,I reinstalled my windows and changed the driver version and still happining
My XPS M1710 started to show vertical green lines during boot up, then would go to a black screen. So I restarted in safe mode,
then disabled the video card.
It starts & runs fine now, no green lines, just reduced video performance, obviously.
This shows there is a problem with the video card. What is the best option now? New, used, or do they fix these?
I'm swapping out my 7900 GTX for a new 7950 GTX. Do I need to download anything specila to overclock it? Or will the stock Dell or G-Force drivers allow me to do so through the Nvidia control panel?
View 14 Replies View Relatedgaphics card has bitten the dust.
M1710 not overclocked
was working fine at the office, when i get it home on de hybernating the screen scrambled progresivly getting worse.
On restart there is a matrix style back ground behind the dell start up logo?
isnt this VGA generated? or does graphics card handle things from power on?
If i allow to boot normally it blue screens and says its graphics driver
I have not inslalled new drivers
it will boot in safe mode but there is still pink dotts behind all images, again isnt safe mode boot in safe mode with graphics from mother board in VGA
have disembled and resembled laptop and made sure graphics card is seated properly has made no diffrence
I'm currently jumping for joy right now. I FINALLY found a fix for those of us with an XPS M1710 and a 7950.
I was getting BSODs on drivers, nvlddmkm crashes in Vista, LCD Flickering in XP and whatnot.
I traced the problem to the way Memory controlling is handled in BIOS A07. If I would take out 1GB of DDR2, I would have no issues. Put back in the other GB and the issues would resume.
After downgrading to A06 I haven't had a SINGLE crash in Vista
For those of you that want to try A06 , I uploaded it to my site for you
XPS M1710 BIOS - A06
My nVidia Geforce Go 7950 GTX burned out about a month ago and I have been running it in VGA mode here in Dushanbe, Tajikistan.
Because I knew that Dell did not have support in this country I didn't contact support until last Friday, April 10, 2009. I had bought a full 4 year warranty when I bought the machine and the warranty expires in Sept 2011.
Dell agreed to replace the GPU under warranty, but said that they could only ship it to somewhere in the States, so I had them ship it to my office in Washington, D.C. and the package is now on its way to Dushanbe by DHL. I'll go inside and change the GPU myself, which, though, I'm not very handy with tools, I think I can do. I have the service manual and have reviewed the procedures and many of the very helpful posts on this site.
My question is that Dell Support is sending both the GPU and a new motherboard in case I need the latter. How do I know whether I need the latter, and should I just replace the motherboard even though the existing one seems to be running fine?
Dell shipped the parts to me on Sunday April 12 and they were received in my office in Washington on April 14. The invoice listed the total price for the GPU and motherboard at $1171.24, which apparently must be paid if I don't send the defective parts to them within 10 days.
Because I'm in Tajikistan Dell Support got a waiver of the 10 day deadline for return. I might just hang on to everything until I'm back in the States in October 2009.
Looking for original M1710 - Geforce Go 7950 GTX Bios. I want to re-flash my video bios back to the original. Is the bios on the JLMOD.ISO CD? If so can someone tell me whats the file name?
View 12 Replies View RelatedI haven't put in my 7950 gtx yet because when I threw the one in that I had here it was DOA so I had to send back to the seller to replace, so the new one should be here in a week. Anyways here is the deal . .
Everyone is claiming since the 7900 GSX pulls such great scores in 3dmark05 (simular to the 7950) it is about the same. Here is the difference. When yall run 3dmark it defaults to a low resolution test. So here is an example. Im pulling low 9k with my 7900 GSX at default resolution. So I got a full version serial number for 3dmark05 and switched the resolution to 1440x900 and ran the tests with that. This should really show the memory difference and power of the better card.
The 7900GSX pulled 4262 at that resolution.
From what im finding online the 7950GTX at 1440x900 resolution pulls around 6700 at that resolution . If you have a 7950GTX test it out and post that instead.
Im sure at 1920x1200 resolution the differences would become even more apparant. So there is the final answer.
High resolution gaming (native resolution on our lappys) will show a big difference.
I have a 1710 thats a couple weeks old and I have a problem. As of right whenever I install drivers other than the dell drivers for my 7950GTX and am running on battery the screen breaks up into a bunch of vertical tears. So far I have used both the Laptop Video 2 Go drivers with the tweaked INF and Geforce Tony's recommended drivers and as soon as I unplug the power I get this problem. But like I said, if I uninstall those drivers and load the current drivers from Dell.com everything works great.
View 15 Replies View RelatedIs it normal that dell.ca would have fewer choices of screens than dell.com? I'm looking at the studio 15, and dell.com lists Hi Resolution/Bright,
glossy widescreen 15.4 WLED display (1440x900) as a choice, which is what I want, but dell.ca doesn't. When I view the system specs though, that choice is listed as on option.