My Inspiron E1505 will not complete it's boot. It comes up with this error:
PBR 1...done
[XLDR] ATA error
F11 shows no recovery, diagnostic test shows no error. Tried F12, checked F2. I am not that tech savvy but can get around to any instructions giving to rectify my issue. I don't have a boot disk, never can with the laptop.
Inspiron 15R SE 7520..When I attempt to start my laptop it goes to the Dell logo screen and will not boot Windows 8. I've had the computer less than a month and if I have to restore the system completely it will not cause much of a problem.
View 16 Replies View RelatedMy laptop froze and I was unable to do anything so I forced shutdown on it, I rebooted it and I noticed I was on the boot screen for a long period of time (about 10 min).
I ran the System Quick test in the UEFI BIOS and everything passed except
"Hard Drive Short DST Check: FAILED".
FAILURE ID: 6CQ8HW-6K1788-MFPX0K-60QG03
PRODUCT ID: C2N47UA#ABA
I have an Acer 8930G, it's knocking on some years (approx 7ish) and this is the first problem I have had with it. When i turn it on, the normal Acer screen shows up and then where it would normally load to windows it just blacks out. There is still power as the all the lights are still working and there is a white-ish light which looks inside the base of the screen. I have looked around on the web and have tried the flashlight on the screen and also removing battery / power cable and holding down the power button for a minute and rebuilding and trying again, but to no avail. I am able to get onto the BIOS screen, and it did look like the boot device in position 1 was the BD drive, I moved this back to the hard drive but still the same....
View 9 Replies View RelatedI'm not able to get past the initial logo screen. It just hangs, pressing the blue thinkvantage button does nothing. F12 likewise. Not able to get any sort of boot menu. Bootable CD in drive lights flash, no boot.
Have tried:
Reseating hard drive
Reseating Dimms, swapping and plugging in one at a time
Removed battery and held power switch down to discharge
This is a type 2714-CTO R500 ....
My HP TouchSmart tm2 with the product number of VL618AV won't turn on past the logo screen. I really don't understand why this is happening because it is just over a year old. I have Windows 7 and there are no error messages on the computer.
View 5 Replies View RelatedSystem is asking for password which is not known. how do I recover. Tried to download recovery file to usb from HP Website but can't get it to load from USB when turning on computer.
View 6 Replies View RelatedI have a Dell Inspiron 1545. So, a few months ago, I got mad at my laptop and slammed the screen down. I think it was taking its sweet time shutting down or something. I can't remember. Anyway, the next time I tried to turn it on, it goes into Startup Repair, and then comes up with a screen of errors, namely "StartupRepairOffline", "Autofailover", "NoOSInstalled". I can go into advanced options and go into DOS command (it comes up to the X drive); I was able to successfully pull off stuff I wanted, but I'm thinking I damaged the hard drive. I've let this sit for awhile, using my daughters' laptop, but now I want mine back and want to repair it. What should I do first? Also, I don't think I have any startup disks or anything like that.
View 5 Replies View RelatedWhen I power up my laptop it won't go past the dell logo. I tried the removal of the battery test. I also tried running the diagnostics test and everything was good. There were no error messages. What can I try next?
View 7 Replies View RelatedMy laptop will not boot up, just get the 7 beeps and a black screen. I have done research on this issue and it seems to be an ongoing problem with this laptop. If this is the case, this should be taken care of by Dell.
View 4 Replies View RelatedDespite the ever-present warnings about ensuring one records passwords, I have recently changed my password and now cannot locate/remember the new one. The computer is an Inspiron 1440 running Windows Vista Home Premium. Is there any way I can reset the password?
View 1 Replies View RelatedI fitted a new LCD panel to an Inspiron 3520. Upon boot, it showed the Dell logo, then went all white and then displayed a grid made up of RGB pixels across the screen. I checked the panel was connected properly and the tried to reboot but now the screen doesn't power up at all. The laptop also now plays 4 beeps while trying to boot. I've tried connecting an external monitor, but it also does not display anything an plays the 4 beeps.
View 3 Replies View RelatedI have an HP Pavillion model 17-e019dx running Windows 8. Every time I turn it on, it stops at a blue screen that says
Recovery
Your PC needs to be repaired
A required device isn't connected or cannot be accessed
Error code 0xc000000f
When I press enter to "Try again" it come back with:
File:WindowsSystem32winload.efi above the error code listed above.
I have tried the Recovery and after MUCH time waiting, it still comes back to the above mentioned screen. I have also run all the diagnostics that are available on the laptop and everything come back normal. I don't have the original discs or documentation as I "received this laptop as a "gift/curse" . It is, however, registered to me.
my inspiron E-1505 that I haven't used in a couple months won't boot. It has power and is charging the battery. The battery is okay. I get lights on the unit when I push start but nothing past that. If the cmos battery was dead would it start anyway? I took the HD out and put it back in. I get nothing on the screen and no sounds at all. The led's on the MB all flash during start.
View 2 Replies View RelatedI had to uninstall the current driver. After this it auto installed the old ati driver.
I uninstalled this one as well leaving me with the bare bones driver that comes with windows. After installing the modded driver again and restarting it began to work again................................................
I've had my trusty Dell Inspiron 6400 since 2006 and it's still going strong, but over the last couple of months
I've noticed that the screen doesn't appear to be as bright as it used to be. It's as if the brightness isn't set to full, but when you try to increase it you discover it is at full brightness.
Can LCD screens become dimmer over time and would a replacement screen fix this?
I own a Dell Latitude E5510. I *love* this laptop.
However, today I started having a problem with it. The laptop turned off suddenly. When I went to turn it back on, it began to load as usual with the following things on the screen:
1. the circular logo in the center of the screen.
2. the "press f12 for boot menu" thing in the top right corner.
3. the blue loading bar beneath the circular logo in the center.
What happens is the blue bar fills up, but then the screen goes black. It doesn't just instantly go black though. It starts from the top of the screen and moves to the bottom. It does the same thing when I press f12 to get into the boot menu.
I have been working on computers for almost 20 years and this has me completely confused. My Aspire V3-571-6643 laptop was working fine until just recently. The system will power on and show the Acer screen and then immediately reboots. It will stay in this reboot loop until manually stopped.
I cleaned and reseated the RAM module and also tried it in both slots with no change. I was able to access BIOS and determined the drives and all settings are correct and even reset to factory defaults with no change. I then pulled the HDD to use in a docking station to determine if the drive was salvagable. Everything reads fine and passed both short and long tests via SeaTools. With the HDD installed the system won't try to boot to CD/USB but after removing it the system will boot to CD just fine. I then ran a full scan using Eurosoft Pc-Check and everything is fine. I reinstalled the HDD and immediately get the reboot loop again.
At this point the mainboard and HDD both test fine independently but will not work together. My only guess is that the mainboard is no longer supplying enough power for all of the components and crashing when the HDD tries to spin up on boot. That, or the SATA controller is malfunctioning and only working for the ODD.
I'm a PC repair technician and have been working on computers for almost 20 years and this has me completely confused. My Aspire V3-571-6643 laptop was working fine until just recently. The system will power on and show the Acer screen and then immediately reboots. It will stay in this reboot loop until manually stopped.
I cleaned and reseated the RAM module and also tried it in both slots with no change. I was able to access BIOS and determined the drives and all settings are correct and even reset to factory defaults with no change. I then pulled the HDD to use in a docking station to determine if the drive was salvagable. Everything reads fine and passed both short and long tests via SeaTools. With the HDD installed the system won't try to boot to CD/USB but after removing it the system will boot to CD just fine. I then ran a full scan using Eurosoft Pc-Check and everything is fine. I reinstalled the HDD and immediately get the reboot loop again.
At this point the mainboard and HDD both test fine independently but will not work together. My only guess is that the mainboard is no longer supplying enough power for all of the components and crashing when the HDD tries to spin up on boot. That, or the SATA controller is malfunctioning and only working for the ODD.
I have a new E1-572G laptop. Long story short, I installed Win 7 on it, and after that, Ubuntu 14.10. I had issues with bootloader, but after fiddling around with legacy/UEFI booting, secure boot, and things like that, I almost successfully configured the laptop. When I selected the ubuntu uefi bootmgr in the bios, in secure boot mode, I rebooted the laptop for what I thought the last time, but then it did not go past the Acer logo. Only combination that works is ctrl+alt+delete. If I remove the hdd, then the acer logo flashes for half a second, and a black screen appears, with a static console cursor at the left upper corner.
I searched a lot in the topic, wanted to reset the bios, but there is no jumper for this, nor can I remove the bios battery. I wanted to reflash the bios, but I could not find proper instructions on this.
I have a Studio 1558 laptop, about 3 years old and a couple of weeks ago it stopped working.
When I press the power button (both on battery and on mains supply) the power button lights up white and stays white and my backlit keyboard lights up. I can hear the fan whirring but thats all that happens. It will stay like this for ever until I press the power button and it then shuts down instantly. There is no BIOS screen and I get no POST beeps.
I've tried plugging it into my TV as an alternative monitor but there's still nothing. I've checked the hard drive and swapped it for a new one but it still makes no difference. I've checked the memory and that's fine. If i try to boot up with the memory removed I do get two beeps.
HP Pavilion dv7 with windows 7 home premium I just got it from my uncle who hasn't use it for long time. Long enough where He forgot his login password and there is no guest just his one account. So my problem an what I'm trying to figure out is if it's possible how could I get to the control panel or is there anyway I can create myself an account.
View 1 Replies View RelatedThe laptop wouldn't boot. I took the keyboard out to see if I could swab-dry any water, but couldn't really find any in there.
I lightly sprayed around with compressed air and left the laptop open with the keyboard out to try and let it dry out for a few hours, but no dice...still wouldn't boot.
I thought maybe via cell phone logic, it might work again after 24 hours or so. It's been almost three days now and it still won't boot, so I'm pretty sure I fried something. Here's the error code it's giving me .....
When I boot my laptop the screen stays blank. You here the start up but screen still black as if not started. The blue symbol on F4 key lights up a 9 in a lock!! How I can get the screen to work?
View 16 Replies View RelatedHave had my Inspiron N5010 for 2 years and I now have the following error codes after running the diagnostic utility:
Error 0123 (2000-0123)Memory Integrity test failedError 0142 (2000-0142)Hard drive 0 : Status 79
I assume a new disk will be required.
My Dell Inspiron 1764 laptop will not boot up after using windows 7 installation disc in repair mode, as it has to restart several times during set up, it would not restart after first phase of operation. It never got to finish operation. Now it is just coming up with a black screen saying,Windows boot manager Windows failed to start. A recent hardware or software change it might be the cause. To fix the problem:
1. insert windows installation disc and restart computer (which it will not let me do)
2. choose your language settings and then click next
3. click repair your computer
if you do not have this disc, contact your system administrator or computer manufacturer for assistance
file: BootBcd
status: 0x000000f
info: an error occurred while attempting to read the boot configuration data
After start up even pressing F8 before logo disappears numerous times it will not let me into that menu, so I cant access start up in safe mode or last known good configuration. No matter what I do it will not go past the above message on screen. I do have 1 year left on my warranty..Even pressing power button for 30 seconds with power disconnected, or pressing F8 button several times on start up doesn't go into menu at all....
So my wife just got a brand new macbook about a week ago, but accidentally dropped it about a foot or two this morning. The "case" which we got from macmall did practically nothing, and I think one corner of the macbook took the brunt of it.
Now, the macbook won't get past the grey startup screen. I'll see the mac symbol, and then a "no entry" (circle with a diagonal line through it) sign, and then the system will just hang.
I've used the Mac OS X install dvd to use Disk Utility to try to repair the hard drive, but Disk Utility didn't find any problems. Everything was green and good to go.
I'm running the Hardware Test now, but I was wondering if anyone here would have any ideas about what to do next, or what is causing this problem?
Update 1: The hardware test said everything was fine, too.
Update 2: It can boot in safe mode! Everything looks good from the safe boot, I've got access to all the files and everything..........................
can't get my laptop to boot up/start. No sounds. No beeps. No nothing. Power cord indicates it is working fine. Battery should be charged since I rarely operate it under the battery. Has been running fine, no problems, I paused a movie and since then it is completely dark and not operating. Really disappointing since it is my main computer that I use every day.
View 3 Replies View RelatedI have a 14z that I purchased last August with Windows 7. It freezes at the DELL logo, and I cannot even do a F2 or F12 to try and get to any of the advanced menus.
View 5 Replies View RelatedDell Inspiron 17R laptop, close to 2 years old.
For a couple of months, the laptop refuses to boot when turning it on. Screens stays completely black, never reaches the Dell-logo. The power-LED burns normally, CPU lights up for a few seconds, then dies out. I hear the fans starting and I think the hard disk starts as well.
The speakers start making an intermittent beeping sound, short beep every +- 3 seconds.
At this point, I have to interrupt the proces, and restart. Occasionally, the computer does start normally (around 10-30 times trying). In the beginning, this took only a few times trying, but it's getting worse.
When the computer comes back from sleep, it doesn't have any problems, only when it's (re)started, or coming from hibernation (deep sleep).