My laptop froze and I was unable to do anything so I forced shutdown on it, I rebooted it and I noticed I was on the boot screen for a long period of time (about 10 min).
I ran the System Quick test in the UEFI BIOS and everything passed except
"Hard Drive Short DST Check: FAILED".
FAILURE ID: 6CQ8HW-6K1788-MFPX0K-60QG03
PRODUCT ID: C2N47UA#ABA
I have an Acer 8930G, it's knocking on some years (approx 7ish) and this is the first problem I have had with it. When i turn it on, the normal Acer screen shows up and then where it would normally load to windows it just blacks out. There is still power as the all the lights are still working and there is a white-ish light which looks inside the base of the screen. I have looked around on the web and have tried the flashlight on the screen and also removing battery / power cable and holding down the power button for a minute and rebuilding and trying again, but to no avail. I am able to get onto the BIOS screen, and it did look like the boot device in position 1 was the BD drive, I moved this back to the hard drive but still the same....
View 9 Replies View RelatedI have a Dell Latitude E6500 that I have been using for quite a long time. Recently it started acting up, and now it won't start up past the Dell logo. It simply goes to a black screen with a flashing dash. I've restarted it a few times, tried pushing F8, and gone into F12. I tried the Diagnostics through F12, but it takes an extremely long time and has never finished so far. I tried it again this morning, and periodically throughout the test a message like this has shown up:
Error Code 0123. Msg: Error Code 2000-0123 Msg: Memory - integrity test failed. The given error code and message can be used by Dell Technical Support to diagnose problem. Do you want to continue testing?
Yes or No or Retry
I'm not sure what exactly this means, but it keeps popping up. I would like to get through to start up my computer all the way, but that doesn't seem to be an option. Is there anyway for me to wipe it without F8? My cd slot won't open, and I don't have disks anyways. Is it possible to fix it via USB drives? Or F12?
My Inspiron E1505 will not complete it's boot. It comes up with this error:
PBR 1...done
[XLDR] ATA error
F11 shows no recovery, diagnostic test shows no error. Tried F12, checked F2. I am not that tech savvy but can get around to any instructions giving to rectify my issue. I don't have a boot disk, never can with the laptop.
I'm not able to get past the initial logo screen. It just hangs, pressing the blue thinkvantage button does nothing. F12 likewise. Not able to get any sort of boot menu. Bootable CD in drive lights flash, no boot.
Have tried:
Reseating hard drive
Reseating Dimms, swapping and plugging in one at a time
Removed battery and held power switch down to discharge
This is a type 2714-CTO R500 ....
HP Pavilion dv7 with windows 7 home premium I just got it from my uncle who hasn't use it for long time. Long enough where He forgot his login password and there is no guest just his one account. So my problem an what I'm trying to figure out is if it's possible how could I get to the control panel or is there anyway I can create myself an account.
View 1 Replies View RelatedInspiron 15R SE 7520..When I attempt to start my laptop it goes to the Dell logo screen and will not boot Windows 8. I've had the computer less than a month and if I have to restore the system completely it will not cause much of a problem.
View 16 Replies View RelatedSystem is asking for password which is not known. how do I recover. Tried to download recovery file to usb from HP Website but can't get it to load from USB when turning on computer.
View 6 Replies View RelatedWhen changing the advance boot options in msconfig, I think I have found a bug. with the option of maximum memory selected, after the restart the computer will only read 3GB (when it should be 4GB). Also when going back in the advance menu of the boot tab, the maximum memory value is 0. (I also have no GUI boot selected, if that changes anything)
View 5 Replies View RelatedI recently bought a HP Pavilion computer (HP Pavilion 10: 10-e010nr). This was my first experience with Windows 9.1, but everything seemed to be going OK. Then, yesterday when I had to enter my password again, the computer began running very slowly and then seemed to lock-up; it wouldn't do anything. I held the "on button" until the computer shut down and then restarted it. When it restarted, it didn't get past the initial screen that shows "HP" within a blue circle and the small circle of small, white dots shows that it's working but nothing ever happens. I tried this numerous times, but the same thing happens.
View 6 Replies View RelatedI have an HP Pavillion model 17-e019dx running Windows 8. Every time I turn it on, it stops at a blue screen that says
Recovery
Your PC needs to be repaired
A required device isn't connected or cannot be accessed
Error code 0xc000000f
When I press enter to "Try again" it come back with:
File:WindowsSystem32winload.efi above the error code listed above.
I have tried the Recovery and after MUCH time waiting, it still comes back to the above mentioned screen. I have also run all the diagnostics that are available on the laptop and everything come back normal. I don't have the original discs or documentation as I "received this laptop as a "gift/curse" . It is, however, registered to me.
System specs:
Lenovo T430U
Intel i5-3427U
8GB PC3-12800 DDR3-1600MHz SoDIMM Memory
HDD 500G 7200rpm Toshiba
mSATA 24GB Samsung Cache
Win 8 Pro, upgraded to 8.1
I rarely use this machine but a couple of months ago I went to boot it up and found that I was not able to get past the Windows splash screen. Sometimes I don't even get the Windows splash screen, I just get a black screen. Rarely I get a Windows screen saying that it is diagnosing a system problem or something to that effect and I can even get to where it will allow me to do some Windows diagnostics but nothing ever comes of it and the process is extremely slow.
I called Lenovo, but of course my machine is out of waranty so the tech just gave me a few pointers and said I could send it in to the depo but the potential repair cost could range up to about 75% of what I paid for the machine in the first place. Anyways, after having me try a few things in the BIOS he suggested that it was likely the hard drive. I mistakenly thought from the time that I bought this machine that the OS was installed on the 24 GB SSD so I ordered a new SSD and swapped it in. This made no difference at all as I have now learned that the mSATA SSD drive is merely for cache to speed up booting.
I am afraid that this means the main HDD is at fault, and quite frankly, if I replace it I am going to do a fresh install of Windows 7. But I do have pictures and docs that I would like to salvage if possible.
I have been working on computers for almost 20 years and this has me completely confused. My Aspire V3-571-6643 laptop was working fine until just recently. The system will power on and show the Acer screen and then immediately reboots. It will stay in this reboot loop until manually stopped.
I cleaned and reseated the RAM module and also tried it in both slots with no change. I was able to access BIOS and determined the drives and all settings are correct and even reset to factory defaults with no change. I then pulled the HDD to use in a docking station to determine if the drive was salvagable. Everything reads fine and passed both short and long tests via SeaTools. With the HDD installed the system won't try to boot to CD/USB but after removing it the system will boot to CD just fine. I then ran a full scan using Eurosoft Pc-Check and everything is fine. I reinstalled the HDD and immediately get the reboot loop again.
At this point the mainboard and HDD both test fine independently but will not work together. My only guess is that the mainboard is no longer supplying enough power for all of the components and crashing when the HDD tries to spin up on boot. That, or the SATA controller is malfunctioning and only working for the ODD.
I'm a PC repair technician and have been working on computers for almost 20 years and this has me completely confused. My Aspire V3-571-6643 laptop was working fine until just recently. The system will power on and show the Acer screen and then immediately reboots. It will stay in this reboot loop until manually stopped.
I cleaned and reseated the RAM module and also tried it in both slots with no change. I was able to access BIOS and determined the drives and all settings are correct and even reset to factory defaults with no change. I then pulled the HDD to use in a docking station to determine if the drive was salvagable. Everything reads fine and passed both short and long tests via SeaTools. With the HDD installed the system won't try to boot to CD/USB but after removing it the system will boot to CD just fine. I then ran a full scan using Eurosoft Pc-Check and everything is fine. I reinstalled the HDD and immediately get the reboot loop again.
At this point the mainboard and HDD both test fine independently but will not work together. My only guess is that the mainboard is no longer supplying enough power for all of the components and crashing when the HDD tries to spin up on boot. That, or the SATA controller is malfunctioning and only working for the ODD.
I have recently acquired an Acer 7220G notebook. Every morning when I switch it on it freezes on the acer splashscreen. I then reboot and it will always load up on the second go.
I have tried switching it off during the day and on again but is always ok. The problem only occurs when the power has been off for a number of hours. It is getting incredibly frustrating have to startup twice each morning.
Ive got a two year old latitude D630 that is shutting down right after the Dell splash screen. pressing down on the left side of the laptop while its booting up and that worked to the point where I got to the login screen, but after a few seconds, it just shut down again.
View 5 Replies View RelatedI have a new E1-572G laptop. Long story short, I installed Win 7 on it, and after that, Ubuntu 14.10. I had issues with bootloader, but after fiddling around with legacy/UEFI booting, secure boot, and things like that, I almost successfully configured the laptop. When I selected the ubuntu uefi bootmgr in the bios, in secure boot mode, I rebooted the laptop for what I thought the last time, but then it did not go past the Acer logo. Only combination that works is ctrl+alt+delete. If I remove the hdd, then the acer logo flashes for half a second, and a black screen appears, with a static console cursor at the left upper corner.
I searched a lot in the topic, wanted to reset the bios, but there is no jumper for this, nor can I remove the bios battery. I wanted to reflash the bios, but I could not find proper instructions on this.
I own a Dell Latitude E5510. I *love* this laptop.
However, today I started having a problem with it. The laptop turned off suddenly. When I went to turn it back on, it began to load as usual with the following things on the screen:
1. the circular logo in the center of the screen.
2. the "press f12 for boot menu" thing in the top right corner.
3. the blue loading bar beneath the circular logo in the center.
What happens is the blue bar fills up, but then the screen goes black. It doesn't just instantly go black though. It starts from the top of the screen and moves to the bottom. It does the same thing when I press f12 to get into the boot menu.
I bought a new X1 Carbon (20A7) a week ago and from time to time the laptop gets stuck on the ThinkPad splash screen when booting. I have to hold the power button to turn it off and then it boots fine. My brother has this problem with T540p, although this happens to him a LOT more often (also, if he waits patiently for 10-20 minutes, the system boots eventually, I havent tried that on my X1).
It doesn't matter if the AC is connected, whether there is something connected to USB ports, whether it was a restart or just normal boot, there is no pattern that I can see, this seems random. We tried updating the BIOS to the newest version, our USB ports are not bent or anything, the SSD with the OS is set as the first boot device. This still happens. I see there are more people with thinkpads who have the similar problem, but their solutions do not apply (if there were any).
Studio XPS 1647 laptop can't boot past POST and stuck at Dell splash screen with progress bar at ~80%. After holding down FN and pressing the power button, all three volume LEDS would flash twice, immediately followed by the volume UP and DOWN keys flashing, and then followed by just the Volume Down LED flashing.
Recently my Studio XPS 1647 has had overheat problems, and sometimes they would cause BSOD with broken screen images. The BSOD always came with bcode 116 error: this is apparently video card related. So last weekend I opened the case, removed the heat sink and the fan. The heat sink vent was completely blocked with a thick layer of dirt, so it's no wonder for overheating. I cleaned up the heatsink vent and the fan, cleaned up the top of CPU chip and the top of GPU chip, reapplied thermal paste and put everything back together. After that, the machine couldn't pass the Dell splash screen on boot. I've already checked the discussions here and followed suggestions on holding down the power button to remove static, reseating the memory card etc., but they are of no use.
Finally I followed the instructions on starting up ePSA. I've tried it repeatedly, and every time the boot always stuck at the Dell splash screen with the progress bar at about 80% with or without applying ePSA. The SPA screen never came up if I held down FN+Power button. The difference between a generic boot and a PSA boot is that if I held down FN+Power button, all three volume LEDS would flash twice, immediately followed by the volume UP and DOWN keys flashing, and then followed by just the Volume Down LED flashing.
I've read from a few discussions talking about all three volume LEDS flashing would be a motherboard problem. But in my case it's three LEDs flashing twice, followed by volume UP and DOWN keys flashing once, and then followed by just the Volume Down LED flashing continuously. What this PSA blinking code means?
Got windows 7 on my g555, with truecrypt on the drive, if it matters. Last night, closed down the cover of my laptop before i fell asleep, like always, today it doesn't respond at all when I opened it back up. Forced it to shut down, and haven't seen anything but a black screen since.
The power light comes on, the fan comes on, and that's about it. Can't get to the bios, can't do ANYTHING. Tried unplugging it for a while, pressing power 10 times, holding power down for a minute, ran the battery entirely dry THEN discharged the caps, ...I've read many solutions where its the built up static charge that's the problem, but not here. I've tried all versions of the solution I could find, all very similar, but none worked. I took out my RAM and put it back in, and same for the hard drive. No dice.
The only lights I get at all are the power light, and the battery charging light next to it. Can't get the CAPS LOCK, num lock, any of that to do anything. Cannot boot by CD/DVD as I cannot change the bios, and can't get any response from any keys or key combos that I can think of (including the one-touch restore).
when I try to install the Windows 8 copy I got with my Lenovo S440 in a virtual box environment
the installation procedure hangs on the windows splash screen. I never saw a Windows 8 installation
procedure before, so I booted my laptop from the installation media to check if it is corrupted.
This works fine. A loading dot circle is displayed under the logo after a few seconds and than after quiet
a while the lenovo wizard is shown... so it has to be an issue with the virtual box.
I attached a screenshot to show you where it hangs.
So my wife just got a brand new macbook about a week ago, but accidentally dropped it about a foot or two this morning. The "case" which we got from macmall did practically nothing, and I think one corner of the macbook took the brunt of it.
Now, the macbook won't get past the grey startup screen. I'll see the mac symbol, and then a "no entry" (circle with a diagonal line through it) sign, and then the system will just hang.
I've used the Mac OS X install dvd to use Disk Utility to try to repair the hard drive, but Disk Utility didn't find any problems. Everything was green and good to go.
I'm running the Hardware Test now, but I was wondering if anyone here would have any ideas about what to do next, or what is causing this problem?
Update 1: The hardware test said everything was fine, too.
Update 2: It can boot in safe mode! Everything looks good from the safe boot, I've got access to all the files and everything..........................
When I power up my laptop it won't go past the dell logo. I tried the removal of the battery test. I also tried running the diagnostics test and everything was good. There were no error messages. What can I try next?
View 7 Replies View Relatedhp pavilion g6 1d63nr-ram; hard drive; fan ; power light have all be checked good after trooubling with information that was provided.
I have a recall plug LS 15-(need Rreplacement) could this be the problem?
Is their damage to the motherboad ?
My HP TouchSmart tm2 with the product number of VL618AV won't turn on past the logo screen. I really don't understand why this is happening because it is just over a year old. I have Windows 7 and there are no error messages on the computer.
View 5 Replies View RelatedDespite the ever-present warnings about ensuring one records passwords, I have recently changed my password and now cannot locate/remember the new one. The computer is an Inspiron 1440 running Windows Vista Home Premium. Is there any way I can reset the password?
View 1 Replies View Relatedi have a 1.5 year old HP PAVILION dv2500.
A couple days ago I tried turning the laptop on, and it just went to an all black screen.
I could not click/type anything (nothing worked), and I couldnt open the CD drive.
After a few minutes, the laptop shut down by itself.
My HP Pavillion Notebook 17-e110dx has stopped working for no discernible reason. When I turn it on it says F1 system information and automatically goes to the F1 screen where it displays the sys info. It says press ESC to exit but that does nothing. In fact, no keys do anything. I tried to get to other screens when booting but it won't let me do anything. The laptop is only a few months old and I still have the basic 1-year warranty. Who should I contact to have HP repair it?
View 1 Replies View RelatedHow do I access the Advance setting in BIOS on Acer aspire 5332 ?I can access bios via the f2 button on startup but there is no advance tab being displayed.
View 1 Replies View Related