I've had my eye on the Sony Vaio VPCZ11 however, I would like to add an external hard drive for data storage, is the USB port the only way of hooking up an external hard drive? How come a high end notebook like this doesn't have a eSATA port?
View 10 RepliesHere's my story and, let's say, my analysis:
I bought a generic 2 HD sata2 RAID1 enclosure based on the chipset Silicon Image SteelVine 5744. It can be used in USB or eSATA2. This embedded chipset (named SiL5744) is known (understand "claimed") to auto-handle Sata I/II and host sata2 controllers that not support the port multiplier feature. The HD are two Samsung F1 1To. There's no jumper to rollback to SATA 1.5Go on them, you can only do it by flashing the HD's bios, however we don't need to do it as I wrote just before, the SiL5744 supports SATA 3Go natively.
The enclosure works pretty well with USB, but *not* in eSATA : the E6500 freezes/hangs just after the POST step (a potential driver issue with the installed vista 64bits is not the reason then). As soon has I disconnect the eSATA cable, the system recovers and continues as normal.
What I've tried/done so far :
Both E6500's BIOS SATA mode AHCI and IRRT mode were tested,
Intel Matrix driver and software was updated to the latest 8.7.0.1007 version (AHCI and IRRT),
The SiL5744 chip was upgraded to its latest firmware as well (in case of...)
In order to verify the esata cable, the HDs and the enclosure itself, I succeed to :
- Use the enclosure's RAID1 feature when using the USB connection, I could partition,format, and read/write on the logical volume
- directly connect *one* HD (Samsung F1 1To) to the E6500's esata port -(I have a sata2esata cable), Vista installed it and I was able to use it as normal, even the hotswap feature seemed to work fine (I unkindly removed it). I could so test both HD individually this way... On the enclosure hardware side, everything looks fine then.
An IMPORTANT thing : The E6500's ICH8/9-M sata host controller seems to support the Port Multiplier feature *ONLY* on sata port 0 -as a bubble message from the Intel Matrix soft sometimes shows up-, but this is exactly where the internal HD is plugged on the motherboard I found nowhere you can change the internal sata port ID (switch,bios,ect...). I think this is the key of the problem that seems to be a dumb port conflict, because the esata port is in fact the port sata 4 (the DVDRW drive is sata 1, dock's esata is 5 for instance). If somebody knows how to swap the sata port ID, I think I won't be toasted !
One more time I am doing the same changing as I did to my previous Vaio Z and TT,
but this time I am having some problem which I don’t understand…………
I have placed some photo in order to see what I am doing,
In the att.
photos you can see the device manager and what happening using the full WWAN European drivers package ,Vaio Smart Network,One Click Internet and the Qualcomm Gobi2000 driver,
It show always the “Qualcomm Gobi 2000 HS-USB Mobile Broadband Device 9225” with yellow warning
I recently bought an FW490J and wanted to add eSATA capability to it. I ended up buying an AKE BC338 because it was the only one that didn't have anything sticking out of the slot itself. However, I can't seem to get this card to be detected by windows.
Actually, i got it to detect once and only once, and after that there was nothing. Has anyone gotten expresscard eSATA working under windows 7? What am I doing wrong? I know this card works because I tried it on another laptop, also with Windows 7(detected and drivers installed).
In particular pay attention to the port on the bottom. This is an "eSATA" port, correct? Now for the crazy question of mine: Is this eSATA port compatible with a male usb connector? I'm pretty sure it isn't, but would like to confirm before I try and destroy something
View 10 Replies View RelatedDell Support said this feature is not supported by them however its there feature (What) anyways can some one tell me that has it working on a XPS 1640 how it is set in the BIOS and what else I need to try to get it to work.....
View 10 Replies View RelatedI pugged a drive into mine for the first time last night (after I figured out that you have to plug in both the eSata and the USB cable for power.)
View 7 Replies View RelatedI have recieved an external hard drive in the post today along with a cable to connect.
I connected the cable, turned hard drive on and nothing is happening. The hard drive connects via usb fine but that will be much slower to backup 500GB worth of data. Does anyone know if I need to do anything special to get it to work with esata or should it work straight away?
Not sure if the cable is esata 1 or 2 but it should work with either shouldnt it?
Acer 6930G's USB/eSATA Port.
Is this port actually able to be used as a USB without any problems(such as for a USB mouse)? Now for the stupid part of the question, once its used for a USB device will I have any trouble using it for an eSATA device later on? Basically wanted to make sure using it as one doesn't lock it into being one specific type of port permanently.
Has anyone successfully used the esata port on their 1557.
I have an esata/usb backup external drive and can not get the esata port to work.
USB 2.0 is slow for a back up drive and moving data.
My Studio 17 has a dedicated eSata port which moves data at 3.0GB/sec. Now I would like an SSD drive, with an eSata enclosure. So I can rapidly hookup, back up and go.
Any ideas of what I need or how to go about this.?
DV 2400 owner here with P/N: GD712AV.
It comes with nVidia 7200 Go video card. Theoritically, nVidia video card could come with HDMI, but not always the case. So..how do I know if mine has one? I am actually looking for eSata port since I want to purchase an external HD for backup purpose.
I used to use my eSATA port every day with a few different devices. I started to have an overheating problem, so Dell replaced the motherboard and graphics card yesterday.
Of course, that means I lost all my BIOS settings. I'm pretty sure I have them back to where they should be (RAID mode on the SATA controller, eSATA port enabled), yet the eSATA port doesn't see a damned thing connected to it.
Every other piece of hardware is exactly the same as it was before. Any ideas as to what I might be missing?
I have an SXPS 1340 running Windows 7 Ultimate. I have tried to connect a Western Digital My Book Home external HD through the esata port but i can't get the computer to recognise it. Has anyone else successfully connected this model HD to the 1340 through esata? To those of you who have successfully connected a different external HD through the esata port what brand and model of external HD are you using?
View 10 Replies View RelatedI have a dell vostro 3350. On windows 7 the sd card and usb 2/esata port work as expected.
On windows 8 they dont. If i install the latest drivers, they work until i reboot the laptop after which they are back to not working.
Is this laptop just not Win8 compatible?
DDR3 PC3-8500 or DDR3 PC3-10600 modules? Two 4 GB modules or a matching pair 8 GB kit?
View 4 Replies View RelatedWhen I adjust the refresh rate on my Z to 60 Hz and restart it, it plunges back to 40.
View 5 Replies View RelatedMy adaptor for my battery of the VPCZ1 gets very hot. Also when I listen to it, it makes a watery sound.
View 8 Replies View RelatedI am planning to get 2x 23inch monitors 1920x1200. So now here is the situation. I want to connect both of these to my sony vaio z. I have found solutions such as the Matrox DualHead2Go box and what not.. But i was wondering if i can get the sony z docking station and use that for dual output. Unlike some other threads that i've read my situation would be to plug the hdmi on the laptop to monitor1 and the dvi from the docking station to monitor 2.
View 10 Replies View RelatedDoes anyone know what the speed is of the iLink port on the new Sony Vaio Z Series Core I7?
I'm trying to decide whether to get the Vaio Z with 3 usb ports or 2 usb ports and 1 iLink port. If the iLink port is a lot faster then the usb ports i'll probably get it with an ilink port. If it's a slow ilink port (400 mbps) then i'll probably get the laptop with 3 usb ports.
It would be nice if it comes with a fast ilink port (800mbps) so i can get a faster connection if i connect the laptop to an external hard drive.
I have bought a Condor 2 X eSata 34mm Express Cardbus Controller for use on my Sony Vaio SZ79N which is running the 32 bit version of Vista Professional.
When I try to install using the supplied installation CD , I get the error message “No JMicron JMB36X SCSI adapter found! Setup program will terminate.”
I have downloaded what seem to be the latest drivers form their web site but can't install from them either.
what I need to run, or what settings I need to add/change or whatever to get the eSata Expresscard up and running?
Trying to get rid of these questionably useful programs -- but I don't see entries for them in add/remove programs in the control panel (or for any of the other useless VAIO software packages that come on OEM machines sans "fresh start")
View 5 Replies View RelatedI have an SR-190 CTO which I've had since last September. Every time I take the laptop off the docking port, it is scorching hot. Has anyone else noticed this? And when I took the laptop off tonight, the battery was at < 10% even though it had been on the dock for a couple hours. I also cannot for the life of me remove the battery...I'm really hoping it's not melted to the laptop or something.
Has anyone else had related issues with the SR docking port? I'm still in the 1-year (though I also have an extended warranty), but this sort of problem really )@#%*s me off.
So ensuring i didnt get a defective device and while i'm still within my 14 day return period I was wondering if other people with the FW series (I have the 465J) version have a little give on the piece on the laptop where you plug it in to charge (top left of the laptop) and if you press it on the top part of it, it sorta pushes in a little bit. I also noticed its easily scratched as a I have a small scratch right where the the screen touches that part when closing the laptop (look at it from above as you slowly close your screen youll notice a little piece sticking out from the screen that can scratch the power input piece).
After rereading my own post I think people might confuse the power input to the power adapter, I'm referring to the place where you plugin your laptop located on the top left of the laptop near the hinge.
what COM port my serial port is on my XPS M1710. Is there a program that I can find all this out in Windows that I just never knew about?
View 12 Replies View RelatedThinking about getting one to go with my m4500 which is on order. Reviews seem ok though some complain it's bulky and other complained the release mechanism wasn't great. Worst was that someone said their comp wouldn't boot when docked.
Can anyone share experience and/or high res pics of what one looks like?
i have a sony VGN FZ440e lappy and just converted my vista to xp. i made everything work except for the parallel port and hdmi slot (doesnt seem to detect). i know that theres a problem with the hdmi audio output
View 5 Replies View RelatedMy HP Pavillion 15 sleekbook has a digital media port on the side that does not read my Sony 64mb memory stick, although it fits fine. After being put on hold for an inexcusible amount of time the tech, that I could hardly understand said it wouldn't work. Why not, and if not what will?
View 7 Replies View RelatedDoes anyone have a link to a website or PDF describing how to properly open and disassemble a VAIO VGN-SZ75GN?
I have a VAIO VGN-SZ75GN, bought about 8 months ago, and now I want to exchange the built-in hard-disc with a solid-state disc.
I need some guide with illustrations/pictures, how to reach the disc
I have just been given a VAIO PCG8A2M (GRX316MP) , i was told "it's broken but if you can fix it yo can have it" so having a quick look at it there's no sign of life on the display but the lights come on and i can here the HDD heads moving about.
Looking a little more i found that all the ram is missing , so now im not sure if its worth buying some ram to see if it works or not ? The lack of ram would prob explain the lack of display but i wonder if i should be getting POST beeps at least, which im not.
So my question is if a VAIO had no ram should (if all else was working) it be getting POST beeps ?