I just ordered an XPS "Geniuine Keyboard" m1710, and it came and it isn't silver whats up with that?
My buds m1710 is silver. mine is gey.
did they change the part #?
what is the part # for the silver one?
and where could I get one .
Well the black keyboard that comes on the 9400/E1705 is a tad bit too loud for my taste. I was thinking of swapping it out for the M1710 keyboard, if its any quieter. At least mine here on the 9400 you can hear a mile away if you're typing away, and the "Enter" key is especially noisy.
View 12 Replies View Relatedafter few seconds of heavy CPU usage on my x230 termal sensors show temperature slightly above 100 degrees celsius. I think it's way to high and probably should call the service to replace the fan, clean the heatsink etc, but wanted to make sure.For comparison, my previous machine (x201) did not ever go above 85 degrees during similar tasks.
View 3 Replies View RelatedI just recently purchased this ultrabook and I have noticed that the sleep and shutdown functions are not operating as expected. Restart works just fine.
Description of Problem: When attempting to put computer to sleep, the screen goes black, but the system remains on (lights on keyboard on, fan still running). I am unable to recover from this state unless I do a hard power off (holding down power button) or wait 5 minutes, at which point the computer simply shuts off. This sort of... defeats the purpose of "sleep." Haha.Same thing occurs when I shutdown the notebook - screen goes blank, lights and fan stay on, and unless I power off by force, laptop stays in vegetative state for five minutes and then shuts down on its own.In both cases, I am unable to recover from the black screen. No response from the computer, regardless of key combo (Ctrl + Alt + Delete, etc.)
Steps Taken to Attempt Solving: The laptop came with BIOS version Insyde F.09, so I updated the BIOS version to F.13. Didn't fix the problemI went into the BIOS and reset everything to the default settings. Still hasn't solved the problem.I found another thread which the user had the exact same problem as me, but on a different model notebook. I tried using their solution to roll back the BIOS. However, it still didn't fix the problem. [URL] .....
I have an M1710 (3.5 years old), and have recently installed Windows 7.
System stats:
2GB RAM
XPS 512MB NVIDIA GeForce Go 7900 GTX
XPS M1710 Duo Processor T2600 (2.16 GHz, 2 MB L2 cache, 667 MHz FSB)
However, since yesterday, when I press the power on button I just get a strange grey screen. I can't get past this. I left it overnight and in the morning I get the same thing. It is a mainly grey/white screen and if I leave it some more bits of grey appear on it in a strange way. I'm not really sure what to do. I've never openened my laptop up to remove dust but have blown through the fans a few times so I imagine that it is very dusty inside.
I bought an XPS13 i7, installed the BIOS (that went fine) and then installed the drivers. After installing the "WiFi Display" driver, the computer will not restart. Here is what happens:
I select the restart option
it shuts down
it powers up (the Dell logo appears)
it then goes to a grey screen.
After approximately 10 seconds (or after I press enter) a progress bar appears at the bottom of the screen with the words "F12 Options." The progress bar is persistently at 99% or thereabouts the computer is completely frozen and nothing happens
If I then press the power button, it powers off. When I press the power button again, it starts perfectly normally.
The main concern for me is that this is the second XPS13 from Dell in 1 week!!! The first one had an almost identical problems after the driver installs but it couldn't even be powered back into Windows. No matter what you tried, it simply went to the screen with the progress bar and froze.
Looking on Dell outlet and noticed that color scheme. I was wondering how it looks since I was planning on a Jet Black, but the Graphite Grey sounds nice too
View 9 Replies View RelatedMy Dell Inspiron 3520 screen goes grey with horizontal lines during use. It reminds me of an old TV except the lines do not scroll. It started after I upgraded from 8 to 8.1.
View 18 Replies View RelatedMy laptop is not booting and the screen is two tones of grey when I try to boot.
I was working on it and left it alone for an hour and when I came back the screen was grey and have not since been able to get it to shut down or start up.
Is there a guide available anywhere showing how I am supposed to renew the thermal paste on these laptops (I have 1645 in particular). I heard it can have a great deal of effect on temperatures.
View 10 Replies View Relatedi just recived my tube of artic Solver 5 and i need some help on how to properly apply it.
how to i get to those parts, ie. what screws do i need to remove.
Dell replaced my motherboard and heatsink for a second time due to heat issues. In the last couple of days, I've noticed it's climbed yet again.
I'm now going to try Artic Silver 5 to see if that'll be up to the job, in a last ditch before I have to get Dell out here again (I'm not impressed with this at all).....................................
i got a dell XPS M1710 Its been overheating lately (gpu kissing 90) and shutting down i blew out the air vents and got tons of dust out but its still running hot. I figure its got a lot of dust up on the heat sinks and the like. That seems to be the main problem i noticed cruising the threads here. Its under warranty still so i called dell to come out and dust it, ect. They said they'd do that and replace the fans/heatsink, ect. I guess that's fine, but when i asked if they use AS5, or if they would if i provided them with some, the guy said they dont because it can cause shorts in laptops or something ... is this true?
I asked what they use and he said thermal pads and some kinda paste combo.. thermal pads generally suck, if theyre replacing all this wouldn't AS5 be the best bet? or can it really cause problems. If its being taken apart and switched up id really prefer the guy slapping some AS5 on there even if i gotta buy it.
someone else sugested offering to use AS Ceramique since that should be non conductive, but ive never used that before. My main concern is that if theyre taking it all apart i dont want pads and their junk back on there, because i always thought pads suck.
can the silver really cause a short?
Also i was thinking that maybe i dont want them replacing the fans. Im pretty sure they use refurbished junk with the parts, wouldn't it be better to leave the old fans that worked fine in there, instead of risking some broken piece of junk being slapped in?
i called them over a week ago before going on vacation and they said i couldn't set up an apointment more than a week out so i had to wait till i got back. I just got home today and am waiting for some sugestions before i call them and set this up
I've noticed that it's not that easy to get access to the CPU and GPU in the M6400, on the M4400 it's much easier, anybody has done it before ?
View 5 Replies View RelatedXps m1530 with windows vista . When I could boot the laptop after a while it then shut off. I did run diagnostics, all passed. I run virus scan - all ok. i updated all drivers and now can not get pass the black screen.
View 1 Replies View Relatedi did some tests before and after applying artic silver to both my cpu and my gpu, here are the results:
Stock cooling temps :
GPU max: 81C
CPU0 max: 75C
CPU1 max: 76C
( the photo was actually incorrect, as i found it was from when i was testing overclocking setups )
then i opened up my lappy and applied some AS5:
CIMG0676.JPG
CIMG0677.JPG
CIMG0679.JPG
and finally my temps are with the new AS5:
temps artic cooling.jpg
( wut? them CPUs are the only ones feelin it :P )
now the air that goes out of the vent is really hot, this did not happen with the stock dell cooling paste.
i just applied it, so should take 200 hours to take full effect
*Update*
After about 190 or 200 hours of use, my temps are really the same... i dont know if it could be winter, because in winter my house gets a bit warmer.. i will, however, try to get to the same room temperatures i had back then and do the stress test
*Update (again )*
After removing and re-applying the AS5, i found out what i was doing wrong:
1- i did not put enough AS5, it needed a bit more for the heat assembly to have perfect contact
2- i did not put enough pressure on the GPUs screws because i was afraid of breaking it
After doing this i find that on the first stress test i get 3 or 4 C lower temps ( from 82 to 79 C ) il do some more stress tests and update the temps.
i have a dell xps 1530, with geforce 8600 gt, i would like to know, if i apply the arctic silver 5, can i reduce some degres? or is it the same?
why dell notebooks has a poor coolling system, when i had the hp pavilion dv6645us i never had problem with temperature and noises
The silver trim that runs around the border of the case is starting to wear away and pit around where my palms rest. Is this something covered by warranty? And if not is it reasonably affordable / simple to fix?
The main reason I wanted this computer was for it's looks, so the fact that it's already starting to form visual defects is really, really annoying.
For those who replaced stock paste with AS5, without making any other alterations how significant was your temperature decline (average CPU and GPU decline).
View 10 Replies View Relatedwoot! think i'm gonna get one. too bad the coupons didn't last this long
View 10 Replies View RelatedMy laptop Acer 5920G doesnt start up anymore. It happend when one day the screen froze and then when i restarted it , it just came up with a grey screen .
Now when i press the power button , the fans starts up and everything and the screen just comes grey sometimes with stripes on it . There is no actual sound eg. vista sound or anything but theres is sound coming from the fans. Once in a while it does boot up and 2 mins later the screen just completely freezes and then when restarted the grey screen thing just happens again.
I was wondering if there are people in the UK who have bought their Dell notebooks either from dell.com and posted to the UK OR delivered to US Address and then brought to the UK
View 4 Replies View RelatedI have three processor questions regarding the M1330:
1. Is it possible to upgrade from the Intel T5250 to the T8100?
2. Are Dell processors a proprietary size or shape?
3. Can I artic silver the processor to make it run cooler?
So my wife just got a brand new macbook about a week ago, but accidentally dropped it about a foot or two this morning. The "case" which we got from macmall did practically nothing, and I think one corner of the macbook took the brunt of it.
Now, the macbook won't get past the grey startup screen. I'll see the mac symbol, and then a "no entry" (circle with a diagonal line through it) sign, and then the system will just hang.
I've used the Mac OS X install dvd to use Disk Utility to try to repair the hard drive, but Disk Utility didn't find any problems. Everything was green and good to go.
I'm running the Hardware Test now, but I was wondering if anyone here would have any ideas about what to do next, or what is causing this problem?
Update 1: The hardware test said everything was fine, too.
Update 2: It can boot in safe mode! Everything looks good from the safe boot, I've got access to all the files and everything..........................
What this icon does and how to disable it ?
View 3 Replies View RelatedNew Dell M4400 user (and new to the forums!)
After giving up with the 1280 resolution on the 13" sony I had for about 2 years, I bought a M4400 2nd hand from a reputable chain of stores in the UK.
It was actually as good as new - all the plastics coverings were still present and untouched both under the laptop and on the palm rest etc. Box was present with all the books/cds sealed
They get a decent supply of Dell and other brands in from resellers/suppliers etc and having worked there in the past, I have no issues with it BUT...
The service tag does NOT validate on the Dell support site. If I type it in another country, it knows that it does not belong to that country.
When I do type it in, it basically says AMERICAS and nothing else.
No warranty information is found, when I hit contact, it basically throws back an error to say the tag was not found.
Have i got anything to worry about?
On another note, while the laptop IS brand new, there are no stickers under the laptop - is this normal on a M4400? The Vista licence sticker is present but under the battery
If It was peeled off, you would know even if it was a slight bit of residue and given that the plastic laminate is still stuck on properly without any signs of it being removed...I am 99.9% sure it never had any stickers on it.
Other than that, I love the laptop - gets a bit warm in the front but it's great otherwise!
T9600, 4GBram, 250GB drive, 15.4 UXGA dual cathode screen@ 1900 resolution etc etc etc
ya so specs are:
x9000
vista ultimate 32 bit
2x 200gb 7200 drives in raid 0
slied 8800gtxs
blu ray reader/dvd burner
psyx card
sound blaster audigy software
4gigs of 667 ram in dual channel mode.
intel wirless
smoke grey
wuxga screen
3 year complete care return to depot warrenty
total 4331. CAD.
EDA nov 13th :C
I'm probably going to re order once I get through all the bs I have been going through with Dell (read here: The continued adventures about a boy and his laptop... .
View 4 Replies View RelatedI just ordered my M6400. the beast will arrive next week. here's the spec :
CPU : QX9300 (2.53ghz Quad Core).
RAM: 4GB (2 Dimms , I may add 2 more soon).
Video : Quadro FX 3700M 1GB Discrete.
Screen : 17 inch UltraSharp WUXGA (1920x1200) LCD Display
HD: 320GB 7200rpm
Integrated 2.0 MP webcam with dual digital array microphone
I've heard many horror stories about the girth of the power brick. is there a smaller/lighter power brick I can get
I bought a 7900 for my dell e1705. When i installed it, there was no screen, but the monitor turned on. I pu tthe 7800 back in and it worked. I dont know what I did wrong, please tell me asap.
Bios are fully updated, A09 (i believe)